Argos Samuel Shorty Bunk Bed Bedienungsanleitung

Samuel Shorty Bunk Bed

Assembly Instructions - Please keep for future reference

Important - Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline:

Argos = 0345 640 0800

Issue 2- 20/06/14

Dimensions

Width - 181cm

Depth - 82cm

Height - 160cm

IMPORTANT NOTE:

The top surface of the mattress

should not come above this line.

IMPORTANT NOTE:

Do not fully tighten

all bolts until all parts

of the bed are

assembled.

162/4131

188/9299

170/8253

• Check you have all the

components and tools listed on

the following pages.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before

starting.

• During assembly do not stand

or put weight on the product, this

could cause damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor.

• Parts of the assembly will be

easier with 2 people.

• To reduce the

likelihood of

damaging your

product please

ensure that your

power drill is set on a low torque

setting.

• Unit weight: 32.5kgs.

Note: if required the next

page can be cut out and used

as reference throughout the

assembly. Keep this page with

these instructions for future

reference.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

Care and maintenance

Handy Hints

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• Assemble all parts and bolts

loosely during assembly, only

once the product is complete

should you fully tighten the

bolts.

• Regularly check and ensure

that all bolts and fittings are

tightend properly.

Warnings

• READ CAREFULLY - RETAIN

FOR FUTURE REFERENCE

• Regularly check and ensure

that all bolts and fittings are

tightened properly.

• Always use the ladder for

entering and leaving the upper

bunk.

• The recommended mattress

size is L1750 x W750 mm.

• Ensure thickness of mattress

does not exceed 175 mm.

• Refrain from using the bunk

bed if any structural part is

broken or missing.

• Please prohibit more that one

person on the upper bunk.

• Please advise your children to

only enter and leave the upper

bunk by using the ladder.

• Please prohibit children from

jumping on the upper and lower

beds.

• WARNING: Children can

become trapped between the

bed and the wall. To avoid risk

of serious injury the distance

between the top safety barrier

and the wall shall not exceed

75mm or shall be more than

230mm.

• WARNING: Do not allow

children under 6 years of age to

use the upper bunk due to risk

of injury and falls.

• STRANGULATION HAZARD -

Never attach or hang items such

as ropes, strings, cords,

harnesses and belts to any part

of the bunk bed.

• THIS BED COMPLIES WITH

EN747-1:2012 / EN747-2:2012

Manufacturer: BL Packaging Co.

Ltd.

Components - Parts

Please check you have all the parts listed below

If you have damaged or missing components, call the

Customer Helpline: Argos = 0345 640 0800

Lower side rail x 2

(75 x 18.5 x 3cm)

3Lower rail x 2

(173 x 7 x 2.5cm)

Upper front safety rail

(173 x 41.5 x 2.5cm)

5Upper back safety rail

(173 x 41.5 x 2.5cm)

Slat x 48

(77.5 x 2.5 x 3cm)

7Ladder

(93.5 x 34.5 x 3cm)

End post x 4

(Ø4.5 x 160cm)

1Upper side safety rail x 2

(73.5 x 35.5 x 3.5cm)

Ruler - Use this ruler to help correctly identify the screws

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170

105

Friendly Tips

• Do not fully tighten all bolts until all parts of

the bed are assembled.

• Assemble lower rails to headboard &

footboard (end panels) first, followed by the

upper safety rails.

• One person must hold on the rails while

another person is assembling it and fitting

bolts to end posts.

• When assembling slats, make sure it is

aligned to the holes on the upper and lower

rails before pushing it firmly down.

• After all the parts are positioned, you can

fully tighten all bolts.

Tools required

Crosshead screwdriver

Components - Fittings

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings

may be supplied than are required.

M6 x 65mm Bolt x 15

A B C

D E F

G H I

Allen key x 2

M6 x 40mm Bolt & Nut x 12 M6 x 20mm Bolt x 8

Screw x 4 Curved washer x 31 Spring washer x 31

Strap x 5 Plastic Cap x 6

Important note: Do not fully tighten bolts at this stage.

Assembling end panels

Position end posts ,

upper side safety rails

and lower side rails

as shown.

Ensure to position

the rails with

middle holes on

the bottom as

shown.

a: Attach lower side rail

into holes on end

posts and fix using

washers & and bolts

. Fasten bolts using

allen key but do not

fully tighten at this

stage.

b: Attach upper side

safety rail to end

posts & fix using washers

& and bolts .

Fasten bolts using allen

key but do not fully

tighten at this stage.

Repeat above steps to

assemble the other end

panel.

Assembly Instructions

Step 1

CFE

E F

a: b:

A EF

C F

A EF AFE

C F

warning

sticker

hole on

bottom

hole on

bottom

A EF AFE

C F

hole on

bottom

hole on

bottom

Assembly Instructions

AFE

Step 2

Assembling lower rails

Important note:

Determine your

preferred upper

bunk bed entry

(left or right).

Ensure to position

holes (for ladder

assembly) on the

lower rails

according to your

preferred upper

bunk bed entry as

shown.

With the help of an

assistant position lower

rails to end panels as

shown and fix to end

posts using bolts ,

bolts & nuts and

washers & . Fasten

bolts & nuts using allen

keys but do not fully

tighten at this stage.

E F

holes

Left upper

bunk entry

Right upper

bunk entry

Important note: Do not fully tighten bolts at this stage.

nut

bolt

Step 4

Assembling upper back

safety rail

Repeat step 3 to

assemble the upper

back safety rail to

left-hand and

right-hand end panel as

shown.

BEF

AFE

BFEB

Assembly Instructions

a: b: 1

Step 3

Assembling upper front

safety rail

Ensure to position

holes (for ladder

assembly) on the

upper front safety

rail according

to your preferred

upper bunk bed

entry as shown.

a: With the help of an

assistant, attach upper

front safety rail to end

post using bolts &

washers & . Fasten

bolts using allen key

but do not fully tighten

at this stage.

b: Attach upper front

safety rail to end post

using bolts , bolt &

nuts and washers &

. Fasten bolts & nuts

using allen keys but

do not fully tighten at

this stage.

holes

E F

Important note: Do not fully tighten bolts at this stage.

nut

bolt

Assembly Instructions

Step 5

Assembling ladder

Important note:

Make sure to

correctly position

the ladder. The

arrow sticker on

the top edge must

be positioned at

the top rail as

shown.

Attach the ladder to

upper front safety rail

& lower rail and fix

using bolts and nuts

as shown. Fasten bolts

using allen keys but

do not fully tighten at

this stage.

Step 6

Assembling upper slats

Insert slats into holes

on upper safety rails

& . Lock it into

position by pushing firmly

down with your hand.

Note: Make sure

the slat is aligned

to the hole before

pushing it firmly

down.

BBB

arrow up

nut

bolt

Important note: Do not fully tighten bolts at this stage.

Assembly Instructions

Securing slats

Attach straps around

end slats and bottom

tube of upper side safety

rails as shown and fix

through holes using

screws . Tighten

screws using a

crosshead screwdriver.

Repeat above steps to

attach other straps to

lower side rails .

Step 8

Step 7

Assembling lower slats

Insert slats into holes

on lower rails . Lock it

into position by pushing

firmly down with your

hand.

Note: Make sure

the slat is aligned

to the hole before

pushing it firmly

down.

A Guide to - Wall Mounting & Fixings

Revision 2 - 7/10/09

Important note:

Types of walls

Care &

Maintenance

No.1 “General Purpose” wall plug

No.6 “Shield Anchor” wall plug

Heavy loads

No.3 “Cavity Fixing” wall plug

No.4 “Cavity Fixing-Heavy Duty”

wall plug

No.5 “Hammer Fixing” wall plug

No.2 “Plasterboard” wall plug

Generally aerated blocks should not

be used to support heavy loads, use

a specialist ftting in this case. For light

loads, general purpose wall plugs can

be used.

For use with heavier loads such as TV

& HiFi speakers and satelite dishes etc.

For use with plasterboard partitions or

hollow wooden doors.

For use when ftting or supporting

heavy loads such as shelving, wall

cabinets and coat racks.

For use with walls stuck with

plasterboard. The hammer fxing allows

it to be fxed to the wall rather than the

plasterboard. Always check the fxing

is secure to the retaining wall.

For use when attaching light loads on

to plasterboard partitions.

Safety: Always check the ftting

and location to ensure your safety

in and around the home.

Fitting: From time to time check

the ftting to ensure the wall plugs

or screws do not become loose.

You can use one of the following types of wall plug if your walls are made

of brick, breeze block, concrete, stone or wood.

Important: When drilling into walls always

check that there are no hidden wires or pipes etc.

Hints:

1: General rule: Always use a larger screw and wall plug

if you are not sure.

2: Ensure you use the recommended drill bit to match the wall

plug and hole size.

3: Ensure you drill the hole horizontally, do not force the drill or

enlarge the hole.

4: Take extra care when drilling high walls, ceilings and ceramic

tiles. Ensure wall plugs are inserted beyond the thickness of

the ceramic tiles to avoid the tiles splitting or cracking.

5: Ensure wall plugs are well ftted and are a tight ft in the

drilled hole.

If plastic wall plugs

are supplied with your

product:

Make sure that the screws and wall plugs being used

are suitable for supporting your unit. Consult a qualifed

tradesperson if you are unsure.

- these are only suitable for

use in masonry walls.

If you are in any doubt about

the correct wall plugs for

your wall, seek professional

advice.

Failure of the product due to

using incorrect fxings is the

responsibility of the installer.

Filling holes

Insert plastic caps into

holes on the top of end

post and lower rail

as shown.

Step 9

1 4

Step 10

Fixing to wall

This unit must be fixed to

a wall.

Move the bunk bed into

position on the wall.

Position the strap to

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung