ARJO HUNTLEIGH Minuet 100500AUS Bedienungsanleitung

1 AH-MIN V3 08/10/17

Minuet®

USER MANUAL

2 AH-MIN V3 08/10/17

CONTENTS

Introduction

Clinical Applications

Assembly

Installation and Disassembly

Operation

Cleaning

Maintenance/ Troubleshooting

Accessories

Warranty and Service

Technical Specification

Parts List

Warnings, Cautions & Notes

Warnings given in this manual identify possible hazards in procedures or conditions,

which if not correctly followed, could result in death, injury or other serious adverse

reactions

Cautions given in this manual identify possible hazards in procedures or conditions,

which if not correctly followed, could result in equipment damage or failure.

Notes given in this manual are used to explain or amplify a procedure or condition

WARNING

The tilt facility, if available, should only be used with the guidance of a clinically

qualified person.

Ensure the bed is assembled correctly in accordance with the instructions in

this manual.

The bed is not designed for patient transport and should not be used for this

purpose.

3 AH-MIN V3 08/10/17

MODEL NUMBER

100500AUS

100520AUS

DESIGN FEATURE

Four section mattress platform

Yes

Two section mattress platform

Yes

Electric tilt adjustment

Yes

Electrical height adjustment

Yes

Electrical backrest adjustment

Yes

Electrical leg with elevation

Yes

Manual leg elevation (straight

leg)

Yes

 This manual provides instructions for the use and maintenance of the ArjoHuntleigh

Minuet ® bed with model numbers listed in the table below

1. Introduction

2. Clinical Applications

Area of Use

Private, nursing and convalescent homes.

Indications

The use of the bed is to assist in patient positioning whilst reducing lifting and handling

stresses for the carer.

The four-section deck allows the patient to be moved to an upright sitting position with

the knees supported or legs elevated.

Contra-indications

The total safe working load of the bed is 180kg (ie. Combined weight of patient,

mattress and accessories)

4 AH-MIN V3 08/10/17

3. Assembly

Check that you have the following parts:

Head end assembly

Foot end assembly

Head end mattress platform assembly

Foot end mattress platform assembly

Control handset

Six clamp screws (loose) and Allen key

Make sure you have enough room to turn the bed from its side to upright when

assembled. Use carpet or other suitable protection to avoid damage.

1. On both the head and foot end column assemblies, turn the castors upward and

apply the brakes (refer to Operations section). Lay the foot end flat on the floor

with the spigots on the frame upper most.

WARNING

Heavy equipment hazard.

The bed and its subassemblies are heavy and appropriate precautions should

be taken to avoid injury when lifting or moving them.

2. Assemble the foot end mattress platform assembly to the foot end.

5 AH-MIN V3 08/10/17

3. Stand the assembled components on one side with the connector sockets on the

backrest actuator or control box (A) uppermost.

4. Assemble the head end deck assembly to the foot end deck assembly.

5. Assemble the foot end to the deck.

6 AH-MIN V3 08/10/17

6. There are a total of 6 clamp screws provided for assembling the bed. Assemble

the first 3 of these clamp screws (B) on the underside of the side rail tube of

one length of the bed. Make sure all joints are fully inserted and tighten all 3

clamp screws securely using supplied Allen key.

7. Carefully thread the head end actuator cable through the support loop (C) on the

frame and connect it to socket 3 (D) on the backrest actuator/control box. Adjust

the cable coils in the loop so the cable is under tension but not strained. Note,

Backrest sheet metal top must be removed by unclipping two tabs (E) in order

to access the control box cable ports.

8. On models with electric leg elevation, carefully thread the leg actuator cable up

through the large hole in the actuator mounting bracket (F). Connect the cable to

socket 5 on the backrest actuator or control box.

B (x6)

7 AH-MIN V3 08/10/17

9. Carefully thread the foot end actuator cable through the support loop (G) on the deck frame and

connect it to socket 4 on the backrest actuator/control box. Adjust the cable coils in the loop so the

cable is under tension but not strained..

10. Connect the control handset cable to socket 1 on the backrest actuator or control box. Clip control

box cable retainer in position and replace backrest sheet metal top.

11. Stand the bed on its castors. Assemble the other 3 clamp screws in the underside of the remaining

side rail tube. Make sure all joints are fully inserted and tighten all 3 remaining clamp screws firmly

using supplied Allen key.

WARNING

DO NOT use the safety side rails to lift or move bed.

WARNING

Make sure that the mains supply cable is not stretched when connected.

Make sure that the handset and mains cable cannot become entangled with

moving parts of the bed.

Lower the bed to minimum height and disconnect the bed from mains power supply.

On both the head and foot end column assemblies, turn the castors inward toward each other and

apply the brakes.

Turn the bed on one side. Disconnect the control handset from the socket on the backrest actuator

or control box. Disconnect the actuator cables from the sockets on the backrest actuator or control

box and remove cables from the support loops on the frame.

Loosen two clamp screws and remove the foot end column assembly.

Loosen two clamp screws and remove foot end column deck assembly.

Loosen two clamp screws and remove the head end deck assembly from the head end assembly.

4. Disassembly—All Models

8 AH-MIN V3 08/10/17

5. Operations

Safety

 Always use a mattress of the correct size and type. A range of suitable pressure

reducing and pressure relieving mattress are available from ArjoHuntleigh.

 Before operation of the bed, ensure that no children, pets or obstacles such as bed-

side furniture are in its path.

 Before operating the bed, ensure that the patient is positioned correctly to avoid

entrapment or imbalance.

 Always apply the brakes when the bed is stationary. When operating the bed in tilt

mode, apply the brakes at one end only.

 Do not expose the equipment, especially the mattress, to naked flames such as

cigarettes etc.

 Use only ArjoHuntleigh accessories designed or approved for use with the bed.

o When moving bed, wrap electrical power cable around Cable Tidy, located at bed head

end in order to avoid damage to cable.

o Ensure the bed is connected to mains power at all times.

o Brakes must be applied before lowering bed to minimum height.

o Bed must be raised before releasing brakes.

o Do not adjust bed height during patient transfer.



 Keep these instructions handy for reference.

Castors & Brakes

9 AH-MIN V3 08/10/17

WARNING

Some functions may cause injury to the patient if unintentional movement occurs.

WARNING

If the Handset is dropped to the floor, caught between bed parts or sustains any damage or

suspected damage in any way, immediately stop using the Handset and perform the full

Handset Checks as detailed in Section 7 - Maintenance.

100520AUS 100500AUS

Power Operation

When a handset push button is pressed, the appropriate bed function will operate until

the button is released.

Leg Elevation -

Model 100500AUS

Using the control handset, the legs are elevated by increasing the angle of the thigh section. When

the legs are raised, the Kneebreak angle can be manually adjusted by raising or lowering the foot

end, which is supported by a self-locking ratchet strut.

To adjust, hold the mattress retention rail and lift the foot end slightly to disengage the latch then

raise or lower it, reversing the movement a little to re-engage the latch at the required position.

Model 100520AUS

The legs can be manually elevated by raising the foot end of the mattress deck. To adjust, hold the

mattress retention rail and lift the foot end slightly to disengage the latch then raise or lower it,

reversing the movement a little to re-engage the latch at the required position.

10 AH-MIN V3 08/10/17

General

Examine the bed for obvious signs of damage. Make sure that all nuts, bolts, clamp screws and

other fastenings are tight and not missing.

Examine the flexible cables for cuts, abrasions, kinking or other deterioration. Ensure that the

power supply connector plug is securely attached and not damaged. If appropriate, check that the

plug fuse is of the correct type (BS 1362 5amp)

If either the plug or cable is damaged then both the plug and cable must be replaced as a complete

assembly by an approved service agent.

6. Cleaning

Warning

Before cleaning, disconnect the bed from the mains power supply.

Gloves and protective clothing should always be worn

when carrying out cleaning procedures.

All surfaces can be cleaned by wiping with a soft cloth moistened with hot water and a mild

detergent. Avoid splashing the actuators and handsets.

Rinse with a cloth moistened with clean water and dry with paper towels.

To remove potentially infectious material such as body fluids, or when used by a client with a known

infection, clean afterwards with NaDCC (ie Presept, Actichlor) at 10,000 ppm of

available chlorine.

Rinse and dry.

Allow cleaned parts to dry thoroughly before replacing the mattress.

Any proprietary furniture polish may be used on the head and foot panels.

Caution

Do not use abrasive compounds or pads.

Do not use hypocarbonate or phenolic cleaning solutions

7. Maintenance / Troubleshooting

Warning

Disconnect the bed from mains power supply before starting any maintenance activity.

The following preventative maintenance procedures should be carried out at intervals of 12 months

or as specified.

All service and repair activities must only be performed by properly qualified and trained technicians

approved by ArjoHuntleigh.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ARJO HUNTLEIGH Medizinische Geräte Handbücher

ARJO HUNTLEIGH

ARJO HUNTLEIGH Akron Streamline 2 Section Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Enterprise 5000X Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Citadel Plus Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Alpha Active 3 Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Alpha Active 3 Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH citadel Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH enterprise 9000 Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Sorrento Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH RotoProne Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Skin IQ Microclimate Manager Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Maxi Sky 2 Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Flowtron Hydroven 12 Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Tenor Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Airtech Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Alpha Active 3 Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Flowtron ACS800 Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH FLOWTRON UNIVERSAL Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Sara Plus Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Sara 3000 Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Bari-Breeze Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH alpha trancell deluxe Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH alpha trancell deluxe Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH Lifeguard LG20 Bedienungsanleitung

ARJO HUNTLEIGH

ARJO HUNTLEIGH CALYPSO Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung