ARTHUR HOLM AH12D 2A Bedienungsanleitung
AH12D 2A – AH12D 216A
AH15D 2HDA
AH17D 2HDA
AH19D 2HDA
AH22D X216GA
Retractable monitors for furniture integration
User manual
Table of contents
EC REGULATIONS & SECURITY 4
SAFETY INSTRUCTIONS 5
APPLICATIONS 6
FEATURES 6
BOX CONTENTS 7
CONNECTIONS 7
CONTROLS 8
OSD MENU 10
INPUT CONNECTORS 13
WARNING 14
AHnet PROTOCOL 15
INPUT SIGNALS 19
PRODUCT WARRANTY 23
Welcome
Thank you for purchasing an ARTHUR HOLM product.
Our product range has been designed to create the perfect meeting room,
where the screens are a part of the interior design as well as essential
communication tools.
Please, read this installation and operating instructions carefully and keep
them in a safe place for future reference.
We remain at your entire disposal if you have any suggestions that would
help us improve our products.
Henrik Holm
General Manager
4
EC Regulations and Security
ATTENTION: Do not disassemble or modify the device in any way.
This symbol warns of the presence of dangerous un-insulated voltages
inside some of the components, of sufficient magnitude to expose people
to risk of electronic shock.
This symbol draws attention to important use and maintenance instructions
in the manual that accompanies the unit.
This symbol indicates that the equipment conforms to the norms
established by the European Community.
5
Safety instructions
PLUGS
– Do not dismantle any part of the monitor power connector
– Disconnect the power plug from the AC outlet when the monitor is not
going to be used for an indefinite period of time
POWER AND EXTENSIONS CORDS
– Use the appropriate power cord with the correct plug type
– Do not overload wall outlets or power cords
– Make sure the total ampere passed through a extension cord does not
exceed the maximum allowed by the cable used
– Do not place anything on the power cord
– Do not locate this product where a person may walk or trip over the cord
Wiring connected to hazardous voltage requires installation by qualified
personnel or the use of ready-made flexible cables.
For your security, your equipment must be connected to an electrical
outlet with grounding connection protection.
The operating electrical outlet must be in an easily accessed place.
ENVIRONMENT
– Install the equipment on an elevated, flat surface
– Install the equipment in a ventilated area
– Avoid exposing the equipment to:
Rain or water
Excessive heat, cold or humidity
Areas exposed to direct sunlight
Dirty areas
Equipment generating strong magnetic fields
– Avoid placing open containers of liquid, near the equipment
– Keep a minimum distance of 30mm in order to have good ventilation
– Never place any sources of flames, such as lighted candles, etc. above the device
– If you are using the device in extreme weather conditions and/or tropical
climates, the equipment should be installed in a room which ensures a
reasonable level of temperature and humidity
- To prevent damage the equipment must be firmly anchored to the surface,
as shown in the installation instructions
6
System Description
APPLICATIONS
The Dynamic2 system is a professional TFT display with an elegant housing and
electrical lift system for installation into horizontal furniture surfaces.
On the starting position (retracted), the screen is placed inside the table leaving
the desk free of any obtrusive elements. When in this position, the power will
automatically be disconnected in order to save energy and preserve panel life.
By pressing the rear button located on the table cover plate, the TFT panel
raises up into the working position (raised and tilted). The TFT power is then
restored.
This TFT-LCD product range is specially designed for desk integration at:
Conference rooms Meeting rooms Board rooms
Auditoriums Information desks Training rooms
FEATURES
- TFT Active Matrix display
A H 1 2 D 2 A 12"
AH12D 216A 12" widescreen format
AH15D 2HDA FULL HD 15"
AH17D 2HDA FULL HD 17"
AH19D 2HDA FULL HD 19"
AH22D 216A FULL HD 22"
- Retractable monitor with electrical engine for furniture integration and tilting
screen 20° (factory adjusted)
- Up/Down function operated by two buttons on the cover plate
- Up/Down external contact close (GPI) or RS-422 control
- Low power consumption
- Low radiation
- Quick response time
- Data inputs DVI-I & DVI-D. HDCP compliant
- Upper cover plate in brushed stainless steel. Monitor housing made of solid
mechanized aluminium in anodised finish
- Electrical powered lift system with variable speed
- Addressable RS422 monitor control by AHnet protocol, RJ45 connector CAT5
7
Communications protocol
System Description
BOX CONTENTS
Before the installation of your motorised monitor, please check the
contents of the shipping box, it must contain the following items:
- Monitor
- Power cord
- Power supply 100-240Vac, 50-60Hz. Output 12V
- Remote control (1 per 5 monitors)
- User Manual
CONNECTIONS
Before connecting the power
1. Open the hatch and remove the two foam protection pieces before
connecting the monitor
2. Install the unit on a table or desk, in vertical position
Power connection
1. Plug the power cable from the power supply into an AC socket of
100-240 Vac, 50-60Hz.
2. Plug the 12Vdc cable into the socket on the unit
Power connection
1. Use the DVI-I input to connect a DVI-D signal or an analog RGB signal
(VGA)
2. Plug the DVI-D connector to a DVI-D signal
Caution! Never use this monitor in horizontal position.
Always use high quality DVI cables with 2m maximum length
8
Controls
REMOTE CONTROL
POWER Switch ON/OFF the monitor
MENU Activates the OSD menu on screen
UP Cursor control up on the OSD menu
DOWN Cursor control down on the OSD menu
LEFT Cursor control left on the OSD menu
RIGHT Cursor control right on the OSD menu
OK Selects the function on the OSD menu. When
the OSD menu is not active on screen, selects
the input source
MONITOR ADDRESS
Below the monitor, there is a screen to configure the monitor. Press the UP
or DOWN buttons to change the function. Press the OK button to select the
function. Change the parameter using the UP or DOWN buttons and press
OK again to save the changes.
AHnet ID Selects the number AHnet ID to RS422 to externally control
the monitor
Input select Selects the input source signal (DVIA, DVI1 or DVI2)
Brightness Configuration of the monitor brightness level
Contrast Configuration of the monitor contrast level
Backlight Configuration of the monitor backlight level
Status information List of the monitor status to service
9
Controls
IR SENSOR
The IR sensor is located on the lower right side of the screen
MONITOR MOVEMENT CONTROLS
On the upper cover plate, there are two buttons to control the UP and
DOWN monitor movements.
1. Retracting the monitor
It is recommended that no objects or parts of the body that could obstruct
the retracting movement of the display, are not on the top of the cover
plate.
To retract the monitor display, press the front button (1) on the right hand
side of the cover plate.
2. Raising the monitor
It is recommended that no objects or parts of the body that could obstruct
the rising of the display, are not on the top of the cover plate.
To rise up the monitor display, press the rear button (2) on the right hand
side of the cover plate. Pressing this button when the monitor is raised,
activates the auto config function for the ARGB input signal.
2. UP button control
1. DOWN button control
10
OSD menu
ACCESSING THE MENU SYSTEM
– With the OSD off, push the MENU button to activate the main OSD menu
– Press the UP and DOWN button to move from one function to another.
Please refer to the following sections below to view a complete list of
all the functions available for the monitor
– Press the OK button to enable the item
– When a function is selected, press the LEFT and RIGHT buttons in order to
change the parameter of the function
Press the Menu button to access to the main menu
PICTURE
CSM Adjusts the colour of the image
Cool
Medium
Warm
User (manually adjustment of red, green and blue colours)
PSM Adjusts the mode of the image
Dynamic
Standard
Mild
User (manually adjustment of brightness and contrast):
Contrast - Brightness - Colour - Sharpness - Tint
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere ARTHUR HOLM Monitor Handbücher
ARTHUR HOLM
ARTHUR HOLM AH10DB2 Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM AH17 NTTHD Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM AH15D X2HDGA Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM DynamicX2 AH22DX216DGA Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM AH19D X2HDGA Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM Gooseneck AH22NTT16 Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM AH1 Series Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM AH10 DA Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM DynamicX2KM Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM RISE AH10 RA Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM RISE AH12RI Wide Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM Dynamic 3 Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM Dynamic3Talk Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM AH17S HDGA Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM AH12D1HGA Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM DynamicX2KM Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM AH 18D3 RHDGA RV Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM AH24DB2 Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM AH17D3 RHDGA TALK Bedienungsanleitung
ARTHUR HOLM
ARTHUR HOLM Dynamic3 Bedienungsanleitung
