ARTHUR HOLM Dynamic 3 Bedienungsanleitung

Assembling guide Dynamic 3 + DTalk

Information

Dynamic 3 monitor is available in a special version prepared to be

assembled with DynamicTalk device. This special version is supplied

with all accessories to be assembled.

DynamicTalk can be assembled at the right side, at left side or at both

sides. This guide shows how to assemble it at left side (the assembling

at the right side follows the same process).

INTRODUCTION

Manipulation of the product should be avoided, no stress should be applied to the product except from

the instructions given in this document. Cutting, drilling, soldering, adding of electrical and mechanical

components can cause danger and should be avoided by all mean. Not complying with these direction

will result in a lost of the Arthur Holm warranty. Albiral Display Solution S.L. shall not be held liable for

any loss or injury incurred as a result of modifications made to goods by anyone other than the supplier

or the supplier's authorised representative without the supplier's written permission. Such

modifications shall be deemed to terminate any further guarantee obligations. Compensation will not be

paid for wages, loss of profit, waste of time, packing and transport or any financial liability resulting

from defects in the goods. (Albiral Display Solutions shall not be liable for any loss or injury caused by

negligence.)

PATTERN HOLE

Pattern hole dimensions for milling are specified in the general dimensions for each reference.

ATTENTION

Preparing the assemble

(x2) DIN 9021 4,3

•Being D3 mounted on the table: Mount the (x2)

washers and the (x2) wing nuts supplied at the bolts

shown. Screw the wing nuts until they are flushed with

the end of the bolt.

(x2) DIN 315 M4

Flush bolt

View from below

the table

View from below

the table

Assembling DynamicTalk 4

•Insert DynamicTalk in the indicated position.

The top plate must be just above the washers

•Turn DynamicTalk until the two open holes

on the top plate are in contact with the bolts

Assembling DynamicTalk

•Push carefully the DynamicTalk upward, please

take care with the hatch of the cover plate.

•There is a guide bolt that has to enter into the

hole of the top plate

•Keeping pressed up the DynamicTalk, screw

the wing nuts with the finger.

Assembling DynamicTalk

•Enter the mounting plate through the DynamicTalk.

•If Dynamic talk has a cable to connect the

microphone: pass the Microphone cable + connector

trough the mounting plate hole.

Assembling DynamicTalk (STANDARD & BOSCH)

•Fix the DynamicTalk to the mounting plate

(x2) DIN 6798 5,3

(x2) DIN 7985 M5x12

Follow This step for standard DynamicTalk or

DynamicTalk with BOSCH

•Fix the mounting plate with washers and screws provided.

(x4) DIN 6798 5,3

(x4) DIN 7985 M5x10

Assembling DynamicTalk (DIS)

•Fix the DynamicTalk to the mounting plate

(x2) DIN 6798 5,3

(x2) DIN 7985 M5x12

Follow This step for DynamicTalk with DIS

or TELEVIC microphone.

•Fix the mounting plate with washers and screws provided.

(x4) DIN 6798 5,3

(x4) DIN 7985 M5x10

Connect XLR connector from the DynamicTalk

to the socket (Microphone IN)

www.arthurholm.com

Dieses Handbuch passt für folgende Modelle

Andere ARTHUR HOLM Monitor Handbücher

ARTHUR HOLM

ARTHUR HOLM AH15D X2HDGA Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM DB2 Series Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH1 Series Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH15D X2HDGA Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH12D 216A Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH24DB2 Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM DynamicX2 AH22DX216DGA Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM RISE AH12RI Wide Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM DynamicX2Talk Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM RISE AH12RI Wide Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH15D3 HDGA Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH12D 2A Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH12D1HGA Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH19D X2HDGA Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM DB2Share Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH10 DA Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM Dynamic3Reverse Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH15DCDHD Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH17D3 RHDGA TALK Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM Dynamic 1H Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH24DB2 Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM Dynamic DB2 Installationsanleitung

ARTHUR HOLM

ARTHUR HOLM Dynamic3Talk Bedienungsanleitung

ARTHUR HOLM

ARTHUR HOLM AH1 Series Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung