Asante IntraCore 40240 Bedienungsanleitung

IntraCore 40240/40480-10G

Layer 3 Gigabit Stackable Ethernet Switch

User’s Manual

IC40240-10G/IC40480-10G

(P/N 99-00837/99-00836)

User’s Manual

sante Networks

47709 Fremont Blvd., Fremont, CA 94538 USA

SALES

408-435-8388

TECHNICAL SUPPORT

408-435-8388: Worldwide

www.asante.com/support

[email protected]

design concept may be copied or reproduced in whole or in part by any means without the express written consent of

sante. Asante and IntraCore are registered trademarks and the Asante logo, AsanteCare, Auto-Uplink, and

IntraCare are trademarks of Asante. All other brand names or product names are trademarks or registered

trademarks of their respective holders. All features and specifications are subject to change without prior notice. Rev.

D7.9 7/4/2009

Management Guide

IntraCore 40240-10G Gigabit Ethernet Switch

•Stackable Layer 3 Switch

•20 10/100/1000BASE-T (RJ-45) Ports,

•4 Gigabit Combination Ports (RJ-45/SFP),

•2 10-Gigabit Extender Module Slots,

•2 Stacking Ports

IntraCore 40480-10G Gigabit Ethernet Switch

•Stackable Layer 3 Switch

•44 10/100/1000BASE-T (RJ-45) Ports,

•4 Gigabit Combination Ports (RJ-45/SFP),

•2 10-Gigabit Extender Module Slots,

•2 Stacking Ports

IC40240-10G (99-00837)

IC40480-10G (99-00836)

About This Manual

Purpose

This guide gives specific information on how to operate and use the management functions of the switch.

Audience

The guide is intended for use by network administrators who are responsible for operating and maintaining network

equipment; consequently, it assumes a basic working knowledge of general switch functions, the Internet Protocol (IP),

and Simple Network Management Protocol (SNMP).

Conventions

The following conventions are used throughout this guide to show information: Note: Emphasizes important information or

calls your attention to related features or instructions. Caution: Alerts you to a potential hazard that could cause loss of

data, or damage the system or equipment.

Warning: Alerts you to a potential hazard that could cause personal injury.

Related Publications

The following publication details the hardware features of the switch, including the physical and performance-related

characteristics, and how to install the switch: The Installation Guide Also, as part of the switch’s software, there is an

online web-based help that describes all management related features.

Revision History

This section summarizes the changes in each revision of this manual.

June 2009 Revision

This is the first release of this manual.

iii

Contents

Section I: Getting Started

Chapter 1: Introduction 1-1

Key Features 1-1

Description of Software Features 1-2

System Defaults 1-7

Chapter 2: Initial Configuration 2-1

Connecting to the Switch 2-1

Configuration Options 2-1

Required Connections 2-2

Remote Connections 2-3

Stack Operations 2-3

Selecting the Stack Master 2-3

Selecting the Backup Unit 2-4

Recovering from Stack Failure or Topology Change 2-4

Broken Link for Line and Wrap-around Topologies 2-4

Resilient IP Interface for Management Access 2-5

Resilient Configuration 2-5

Renumbering the Stack 2-5

Ensuring Consistent Code is Used Across the Stack 2-5

Basic Configuration 2-6

Console Connection 2-6

Setting Passwords 2-7

Setting an IP Address 2-7

Manual Configuration 2-8

Dynamic Configuration 2-11

Enabling SNMP Management Access 2-13

Community Strings (for SNMP version 1 and 2c clients) 2-13

Trap Receivers 2-14

Configuring Access for SNMP Version 3 Clients 2-15

Managing System Files 2-15

Saving Configuration Settings 2-16

Section II: Switch Management

Chapter 3: Configuring the Switch 3-1

Using the Web Interface 3-1

Navigating the Web Browser Interface 3-2

Home Page 3-2

Configuration Options 3-3

Panel Display 3-3

Contents

Main Menu 3-4

Chapter 4: Basic Management Tasks 4-1

Displaying System Information 4-1

Displaying Switch Hardware/Software Versions 4-3

Displaying Bridge Extension Capabilities 4-4

Setting the Switch’s IP Address (IP Version 4) 4-5

Manual Configuration 4-7

Using DHCP/BOOTP 4-8

Setting the Switch’s IP Address (IP Version 6) 4-9

Configuring an IPv6 Address 4-9

Configuring an IPv6 General Network Prefix 4-15

Configuring Neighbor Detection Protocol and Static Entries 4-17

Configuring Support for Jumbo Frames 4-21

Managing Firmware 4-21

Downloading System Software from a Server 4-22

Saving or Restoring Configuration Settings 4-24

Downloading Configuration Settings from a Server 4-25

Console Port Settings 4-26

Telnet Settings 4-28

Configuring Event Logging 4-30

System Log Configuration 4-30

Remote Log Configuration 4-31

Displaying Log Messages 4-33

Sending Simple Mail Transfer Protocol Alerts 4-33

Renumbering the Stack 4-35

Resetting the System 4-36

Setting the System Clock 4-36

Setting the Current Time 4-37

Configuring SNTP 4-37

Setting the Time Zone 4-39

Configuring Summer Time 4-40

Chapter 5: Simple Network Management Protocol 5-1

Enabling the SNMP Agent 5-2

Setting Community Access Strings 5-3

Specifying Trap Managers and Trap Types 5-4

Configuring SNMPv3 Management Access 5-7

Setting a Local Engine ID 5-7

Specifying a Remote Engine ID 5-8

Configuring SNMPv3 Users 5-9

Configuring Remote SNMPv3 Users 5-11

Configuring SNMPv3 Groups 5-13

Setting SNMPv3 Views 5-17

Contents

Chapter 6: User Authentication 6-1

Configuring User Accounts 6-1

Configuring Local/Remote Logon Authentication 6-2

Configuring HTTPS 6-5

Replacing the Default Secure-site Certificate 6-7

Configuring the Secure Shell 6-8

Generating the Host Key Pair 6-10

Importing User Public Keys 6-12

Configuring the SSH Server 6-14

Configuring Port Security 6-16

Configuring 802.1X Port Authentication 6-18

Displaying 802.1X Global Settings 6-19

Configuring 802.1X Global Settings 6-20

Configuring Port Settings for 802.1X 6-20

Displaying 802.1X Statistics 6-24

Filtering IP Addresses for Management Access 6-26

Chapter 7: Access Control Lists 7-1

Configuring Access Control Lists 7-1

Setting the ACL Name and Type 7-1

Configuring a Standard IPv4 ACL 7-2

Configuring an Extended IPv4 ACL 7-3

Configuring a MAC ACL 7-6

Configuring a Standard IPv6 ACL 7-7

Configuring an Extended IPv6 ACL 7-8

Binding a Port to an Access Control List 7-11

Chapter 8: Port Configuration 8-1

Displaying Connection Status 8-1

Configuring Interface Connections 8-3

Creating Trunk Groups 8-6

Statically Configuring a Trunk 8-7

Enabling LACP on Selected Ports 8-8

Configuring LACP Parameters 8-10

Displaying LACP Port Counters 8-13

Displaying LACP Settings and Status for the Local Side 8-14

Displaying LACP Settings and Status for the Remote Side 8-16

Setting Broadcast Storm Thresholds 8-17

Configuring Port Mirroring 8-19

Configuring Rate Limits 8-20

Showing Port Statistics 8-22

Chapter 9: Address Table Settings 9-1

Setting Static Addresses 9-1

Displaying the Address Table 9-2

Changing the Aging Time 9-4

Contents

Chapter 10: Spanning Tree Algorithm 10-1

Displaying Global Settings 10-3

Configuring Global Settings 10-6

Displaying Interface Settings 10-10

Configuring Interface Settings 10-13

Configuring Multiple Spanning Trees 10-16

Displaying Interface Settings for MSTP 10-19

Configuring Interface Settings for MSTP 10-20

Chapter 11: VLAN Configuration 11-1

IEEE 802.1Q VLANs 11-1

Enabling or Disabling GVRP (Global Setting) 11-4

Displaying Basic VLAN Information 11-4

Displaying Current VLANs 11-5

Creating VLANs 11-6

Adding Static Members to VLANs (VLAN Index) 11-7

Adding Static Members to VLANs (Port Index) 11-9

Configuring VLAN Behavior for Interfaces 11-10

Configuring IEEE 802.1Q Tunneling 11-12

Enabling QinQ Tunneling on the Switch 11-16

Adding an Interface to a QinQ Tunnel 11-17

Configuring Private VLANs 11-18

Enabling Private VLANs 11-19

Configuring Uplink and Downlink Ports 11-19

Configuring Protocol-Based VLANs 11-20

Configuring Protocol Groups 11-20

Mapping Protocols to VLANs 11-21

Chapter 12: Link Layer Discovery Protocol 12-1

Setting Basic LLDP Timing Attributes 12-1

Configuring LLDP Interface Attributes 12-3

Displaying LLDP Local Device Information 12-5

Displaying LLDP Remote Port Information 12-8

Displaying LLDP Remote Information Details 12-9

Displaying Device Statistics 12-11

Displaying Detailed Device Statistics 12-13

Chapter 13: Class of Service 13-1

Layer 2 Queue Settings 13-1

Setting the Default Priority for Interfaces 13-1

Mapping CoS Values to Egress Queues 13-3

Selecting the Queue Mode 13-5

Setting the Service Weight for Traffic Classes 13-6

Layer 3/4 Priority Settings 13-7

Mapping Layer 3/4 Priorities to CoS Values 13-7

Selecting IP Precedence/DSCP Priority 13-7

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Asante Netzwerk-Router Handbücher

Asante

Asante IntraCore 8000 Bedienungsanleitung

Asante

Asante FriendlyNET GX5-424W Bedienungsanleitung

Asante

Asante FriendlyNET GX5-424W Bedienungsanleitung

Asante

Asante FriendlyNET FS4124R Bedienungsanleitung

Asante

Asante IntraCore 35516 Series Bedienungsanleitung

Asante

Asante FriendlyNet FS4004DS Bedienungsanleitung

Asante

Asante FriendlyNET FS4005P Bedienungsanleitung

Asante

Asante IntraCore 36480 Bedienungsanleitung

Asante

Asante IntraStack 6014DSB Handbuch

Asante

Asante IntraCore 6524 Bedienungsanleitung

Asante

Asante IntraCore 39240/480 User's Bedienungsanleitung

Asante

Asante IntraCore 3624/48 User's Bedienungsanleitung

Asante

Asante FriendlyNET GX5-2400W Bedienungsanleitung

Asante

Asante Asante FriendlyNET FS4116R Bedienungsanleitung

Asante

Asante IntraStack 6014DSB Bedienungsanleitung

Asante

Asante IntraSwitch 5308FL Bedienungsanleitung

Asante

Asante FriendlyNet FS3208 Bedienungsanleitung

Asante

Asante FS4002E/FS4004E Bedienungsanleitung

Asante

Asante IntraStack 6014DSB Bedienungsanleitung

Asante

Asante FriendlyNET FS4016P Bedienungsanleitung

Asante

Asante FriendlyNET GX5-424W Bedienungsanleitung

Asante

Asante FriendlyNET FS4116R Bedienungsanleitung

Asante

Asante FriendlyNET FR1104-G Bedienungsanleitung

Asante

Asante FriendlyNet FS3208 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung