Asko T208VW Bedienungsanleitung

Dear Customer,

Read these instructions carefully and completely before you install the

machine. The installation should be carried out by a qualiﬁed person who

is familiar with all local codes and ordinances for electrical and plumbing

connections. See also the general Safety Instructions in the Use & Care

Guide.

Cosmetic damage must be reported to the ASKO dealer within ﬁve

days from the date of purchase. As soon as you unpack the machine,

thoroughly check it for cosmetic damage.

Installation instructions for condenser tumble dryer

DOMESTIC

2Customer Care Center

1-800-898-1879

www.askona.com

Installation instructions

WARNING!

WARNING - Risk of ﬁre.

Install the clothes dryer according to the

manufacturer's instructions and local codes.

To reduce the risk of of severe injury or death,

follow all installation instructions.

SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE.

Positioning the tumble dryer

The tumble dryer can be freestanding or

stacked. Remember that the tumble dryer

produces heat and should therefore not be

located in a room that is too small. If the room

is very small, drying will take longer due to the

limited quantity of air.

NOTE!

Do not install the machine in a room where

there is a risk of frost occurring. At temperatures

around freezing point the machine may not be

able to operate properly.

The room in which the appliance is installed

should be adequately ventilated, with

temperature between 15°C and 25°C.

WARNING!

• Clothes dryer installation must be performed

by a qualiﬁed installer.

• For proper ventilation, the machine should

not be installed behind a door.

• The tumble dryer's toe kick ventilation must

not be blocked by a rug or the like.

NOTE!

If the unit must be installed behind a door, the

door should be louvered. (please see door

ventilation requirements in the Built-in chapter).

To improve ventilation, the door where the

tumble dryer is located should be left open

when the dryer is in use.

Freestanding

The tumble dryer can be positioned beside the

washing machine.

Stacking

The tumble dryer can be placed on top of an

ASKO washing machine. Use the two foot cups

found in the document bag included with the

machine and the two tip guards attached to the

bottom of the back of the machine.

How to assemble the stacking kit:

1. Remove the two tip guards from the back of

the tumble dryer. Replace the screws that

held the tip guards in place.

2. Remove the two screws indicated on the

back of the washing machine.

Customer Care Center

1-800-898-1879

www.askona.com

Installation instructions

3. Secure the anti-tip device using the screws

as shown in the picture.

4. Attach the plastic cups for mounting the

tumble dryer’s front feet to the washing

machine’s top cover. This is essential, as

only when the tumble dryer’s feet are resting

in the plastic cups can you be sure that the

tumble dryer is correctly positioned on the

washing machine. Break oﬀtab A on the cup

ﬁtted on the right side and tab B on the cup

ﬁtted on the left side. Then remove the paper

from the self-adhesive surface under the

plastic cups.

5. Fit the plastic cups so that the "tags" marked

with arrows are against the front edge or side

edge of the cover and press them ﬁrmly onto

the cover. Then break oﬀthe remaining tabs.

6. Push the tumble dryer in under the metal

brackets. At the same time keep the front

edge raised by 7/16" (10mm) to 7/8" (20mm) .

7. Lower the tumble dryer’s front feet into the

plastic cups and adjust the tumble dryer to

ensure it is level.

Adjusting the feet

Screw the feet in or out so that the tumble dryer

is both stable and level.

4Customer Care Center

1-800-898-1879

www.askona.com

Installation instructions

Built-in

ASKO dryers can be installed beneath a cabinet

or worktop with a minimum height of 34” (864

mm). There must be a gap of about 1/2” (12 mm)

all around the machine and a minimum gap of 1"

(25 mm) between the rear edge of the machine

top panel and the back wall. The opening

width must be at least 24-1/2” (622 mm). The

condensing models work best when they have

good air circulation.

Install the dryer so the condensed water will

continuously ﬂow into a drain or sink, you

will need a drain outlet behind the unit. The

maximum drain height is 40” (1016 mm).

NOTE!

The height adjustment for the dryer is 33- 1/2”

to 34-1/2” (850 mm to 876 mm). Do not raise it

higher than 34-1/2” (876 mm).

NOTE!

It is very important to avoid a buildup of heat.

The warm air which is expelled from the rear of

the dryer must be able to dissipate.

Warm air which cannot dissipate could cause a

fault.

A buildup of heat could be avoided by:

• Creating a gap for the dryer in the kitchen

furniture plinth facing.

• Creating ventilation gaps in the kitchen unit.

When build under, drying times may be longer.

NOTE!

The dryer should not be installed next to a

refrigeration appliance. The warm air expelled

from the rear of the dryer would increase the

temperature around the refrigeration appliance

heat exchanger causing the compressor to

run continuously. If it is not possible to install

the dryer anywhere else, then the refrigeration

appliance must be sealed oﬀfrom the dryer.

Customer Care Center

1-800-898-1879

www.askona.com

Installation instructions

Install in a closet

ASKO's front panel controls make it possible

to install the washers and dryers in a closet.

Make sure there is a ½” (12 mm) minimum

clearance between units and cabinet or wall

and a 1" (25 mm) minimum clearance between

the rear edge of the machine top panel and the

cabinet or wall. To ensure proper ventilation,

we recommend louvered doors, particularly for

condenser dryers. Otherwise there must be

ventilation openings in the door. See illustration

for minimum ventilation openings:

NOTE!

Ensure the dryer door can be opened without

hindrance after installation.

NOTE!

The cool air intake panel at the front of the dryer

must not be blocked or covered. Doing so could

cause a fault.

Condensed water

Install the dryer so the condensed water will

continuously ﬂow into a drain or sink. To do this,

follow the instructions below:

1 Connect the rubber hose supplied with the

dryer to the blue nipple.

2. Run the hose to a drain or sink, as illustrated.

NOTE!

The drain hose must not be more than 40”

(100 cm) above the ﬂoor.

NOTE!

• Do not pull on the drain hose and do not

stretch it or allow it to become kinked as it

could get damaged.

• Secure the hose carefully (e.g. by trying it to

a tap to make sure it cannot slip during use).

Otherwise there is a risk of overﬂowing water

which could cause damage.

WARNING!

If the tumble dryer is to be connected to a

drainage system already in use by another

appliance it is essential to ﬁt a non-return valve.

The non-return valve will prevent the risk of

back-ﬂow into the dryer which could cause

damage.

6Customer Care Center

1-800-898-1879

www.askona.com

Electrical installation

WARNING!

The receptacle on the rear of the machine is

designed to accommodate ASKO washers

ONLY (rated 208–240 V.) To use this receptacle,

you must use the ready-ﬁtted plug supplied with

the washing machine or an equivalent.

ASKO washers rated 208–240 V have two

internal fuses of 15 A each.

The machine should only be connected to a

grounded wall socket.

WARNING!

This appliance must be properly grounded.

Refer to the “Important Safety Instructions” for

grounding instructions.

The power supply cord must be grounded. If the

machine is to be used in a wet area, the supply

must be protected by a residual current device.

Connection to a permanently wired supply point

must be made only by a qualiﬁed electrician.

As supplied: Single-phase, 230 V, 60 Hz,

3000W heater rating 30 A circuit required.

NOTE!

Do not connect the machine to the mains

electricity supply by an extension lead.

Remove cover to access

teminal box. (Requires- Torx

screwdriver.)

Electrical Connections

WARNING!

Read the Electrical requirements and grounding

instructions before connecting the tumble dryer.

Electric models of the dryer are manufactured

for a 3-wire connection system. The dryer frame

is grounded by a link to the neutral conductor

on the dryer terminal block. If local codes do

not permit grounding through the neutral, the

grounding link from the terminal block must be

removed and a separate ground wire must be

used.

Only a 4-conductor cord shall be used when

the appliance is installed in a location where

grounding through the neutral conductor is

prohibited. Grounding through the neutral

conductor is prohibited for new branch-circuit

installations, mobile homes, recreational

vehicles, and areas where local codes prohibit

grounding through the neutral conductors. The

grounding link on the dryer must be removed for

all 4-wire installations.

These Electrical Connection instructions

provide for installing the dryer in the following

situations:

3-wire connection where local codes permit

grounding through the neutral. 3-wire

connection plus separate grounding connector

where local codes do not permit grounding

through the neutral.

4-wire connection.

Each of the above connections can be made

with an approved power supply cord or by direct

wiring. Each connection instruction identiﬁes

the appropriate Power Supply Cord and covers

requirements for direct wiring.

NOTE!

In Canada, the dryer is delivered ready-ﬁtted

with a four-prong plug intended for connection

to a single-phase supply.

Installation instructions

Customer Care Center

1-800-898-1879

www.askona.com

Connecting a 3-wire Power Cord

WARNING!

Before starting this procedure, be sure the

power is turned oﬀat the breaker/fuse box.

Ground

(center)

Power Supply Cord

You will need a 3-wire power supply cord with

three No. 10 copper wires and a matching

3-wire receptacle of NEMA Type 10-30R, as

illustrated below:

To connect a 3-wire power cord to the dryer,

follow the steps below.

NOTE!

The numbers in the illustration correlate to the

step numbers.

1. Turn the power oﬀat the breaker or fuse box.

2. Remove terminal block cover.

3. Use the strain relief attached below the

terminal block opening.

4. Loosen or remove center terminal block

screw.

5. Connect ground (center) wire of power

supply cord to the center, silver-colored

terminal screw. Tighten screw.

6. Connect the other wires to outer screws.

7. Tighten the strain relief screws.

8. Replace terminal box cover on back of dryer.

9. Plug dryer into wall receptacle.

10.Turn power on at breaker/fuse box.

Connecting a 4-wire Power Cord

WARNING!

Before starting this procedure, be sure the

power is turned oﬀat the breaker/fuse box.

Installation instructions

8Customer Care Center

1-800-898-1879

www.askona.com

Power Supply Cord

You will need a 4-wire power supply cord with

four No. 10 copper wires and a matching 4-wire

receptacle of NEMA Type 14-30R, as illustrated

below.

The fourth wire must be identiﬁed with a white

cover and the ground conductor by a green

cover.

To connect a 4-wire power cord to the dryer,

follow the steps below.

NOTE!

The numbers in the illustration correlate to the

step numbers.

1. Turn the power oﬀat the breaker/fuse box.

2. Remove terminal block cover.

3. Use the strain relief attached below the

terminal block opening.

4. Remove center terminal block screw.

5. Remove ground wire (green with yellow

stripes) from external ground connector

screw and remove from center terminal

block.

6. Connect ground (green) wire of cord to

external ground conductor screw.

7. Connect neutral (white) wire of cord under

center screw of terminal block.

8. Connect the other wires to outer screws.

9. Tighten the strain relief screws.

10.Replace terminal box cover on back of dryer.

11.Plug dryer into wall receptacle.

12.Turn power on at breaker/fuse box.

Installation instructions

Customer Care Center

1-800-898-1879

www.askona.com

10 Customer Care Center

1-800-898-1879

www.askona.com

Andere Asko Trockner Handbücher

Asko

Asko PROFESSIONAL Bedienungsanleitung

Asko

Asko 7003 Betriebsanleitung

Asko

Asko T741C Bedienungsanleitung

Asko

Asko T794 Bedienungsanleitung

Asko

Asko T754 Montageanleitung

Asko

Asko T2082H Bedienungsanleitung

Asko

Asko TDC177XV Bedienungsanleitung

Asko

Asko PROFESSIONAL TDC145VG Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Asko

Asko DC 7171 Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Asko

Asko T700 Series Bedienungsanleitung

Asko

Asko T754HP Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Asko

Asko T720 Bedienungsanleitung

Asko

Asko T761 Bedienungsanleitung

Asko

Asko DC7794HP Bedienungsanleitung

Asko

Asko T712C Bedienungsanleitung

Asko

Asko 7705 - Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Asko

Asko TD70.C Bedienungsanleitung

Asko

Asko T743C Montageanleitung

Asko

Asko T712C Bedienungsanleitung

Asko

Asko T700 Series Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Miele

Miele TWH 780 WP Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Bedienungsanleitung

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung