Asko DOMESTIC TD85 Bedienungsanleitung

INSTALLATION INSTRUCTIONS

TD85

Carefully read the instructions for use before using the dryer.

Vented Tumble Dryer

DOMESTIC

2Customer Care Center, 1-800-898-1879, www.askona.com

WARNING - Risk of ﬁre.

Install the clothes dryer according to

the manufacturer's instructions and

local codes.

Clothes dryer installation must be

performed by a qualiﬁed installer.

Do not install a clothes dryer with

ﬂexible plastic venting materials.

If ﬂexible metal (foil type) duct is

installed, it must be of a speciﬁc

type identiﬁed by the applience

manufacturer that is UL approved

for use with clothes dryers. Flexible

venting materials are known to

collapse, be easily crushed, and trap

lint. These conditions will obstruct

clothes dryer airﬂow and increase the

risk of ﬁre.

To reduce the risk of of severe

injury or death, follow all installation

instructions.

SAVE THESE INSTRUCTIONS FOR

FUTURE REFERENCE.

WARNING

For proper ventilation, the machine

should not be installed behind a door.

The tumble dryer's toe kick ventilation

must not be blocked by a rug or the

like.

DRYER PLACEMENT

The dryer can be either freestanding or installed

onto a washing machine.

The dryer emits heat. Therefore, do not place it in

a very small room, as the drying process may be

longer due to limited amount of available air.

Do not place the dryer in a room where

temperature can drop below 0 °C (32 °F), as the

machine may not operate correctly at such low

temperatures or may freeze, which can result in

damage to the machine.

Install the dryer in a room with adequate ventilation

and a temperature between 10 °C (50 °F) and 25 °C

(77 °F).

Do not place the dryer behind lockable or sliding

doors, or doors with a hinge on the opposite side of

the dryer door hinge. Install the dryer in such way

that the door can always be freely opened.

As this is a vented dryer, it does not have a

condensate tank. The handle has solely a decorative

purpose and is ﬁxed; it is not intended for opening. If

excessive force is applied, the handle may break.

INSTALLATION

Dear Customer,

Read these instructions carefully and completely before you install the machine. The installation should

be carried out by a qualiﬁed person who is familiar with all local codes and ordinances for electrical and

plumbing connections. See also the general Safety Instructions in the Use & Care Guide.

Cosmetic damage must be reported to the ASKO dealer within ﬁve days from the date of purchase. As soon

as you unpack the machine, thoroughly check it for cosmetic damage.

Customer Care Center, 1-800-898-1879, www.askona.com

Never block the air exhaust (evacuation

opening).

At least two persons are required to install the

tumble dryer on top of a washing machine.

Do not place the dryer on a carpet with long

ﬁbres as this may impede air circulation.

Freestanding appliance

The dryer may be placed adjacent to a washing

machine.

If the friction between the dryer feet and the ﬂoor is

not suﬃcient, the dryer may move during operation.

To prevent sliding, use a non-slide mat or install the

supplied vacuum feet onto both front feet.

Place the dryer so that it is stable. Use a spirit level

to level the dryer horizontally and vertically by

rotating the adjustable feet using a No. 22 (0.87")

spanner (max. 15 mm (0.59")). Then, ﬁrmly tighten

the jam nuts (counter nuts) by rotating them towards

the appliance bottom using a No. 17 (0.67") spanner

4Customer Care Center, 1-800-898-1879, www.askona.com

Clearance around the dryer for optimum

operation

50 mm (2")

100 mm (4")

The appliance may not be in contact with a wall

or adjacent furniture. For optimum dryer operation,

observe the clearance from the wall as shown in the

ﬁgure.

Opening the dryer door (top view)

1189 mm (47")

480 mm (19")

176°

Stacking on top of a washing machine

To stack the dryer on top of a washing machine, use

the extra vacuum feet and the tipping guard (A+B),

supplied in the cardboard box in the dryer drum.

Tipping guard part B is designed to ﬁt on ASKO

washing machines and it may be hard or impossible

to mount on appliances of other brands. If the

washing machine and dryer are not of matching

dimensions or if you have installed a hidden helper

between the two appliances, then binding plates are

available as optional accessories at the service unit

(available only for HH (accessory Hidden Helpers)

and TD75 stacked on top of WM80 or WM85; not

intended for any other combinations).

All ASKO washing machines can bear the weight of

the dryer.

Washing machine on which you wish to install

the dryer must be able to bear the weight of the dryer

(see washing machine’s rating plate or technical

information).

Customer Care Center, 1-800-898-1879, www.askona.com

How to stack a dryer onto the washing machine (ASKO):

There is a cardboard box in the dryer drum, containing the vacuum feet and the tipping guard.

A B

1The tipping guard consists of two metal parts (A +

B).

Use two screws to attach the A part to the back of the

dryer.

2Undo the screw on the back side of the washing

machine.

3Use the screw to attach the tipping guard (B part)

to the back of the washing machine.

4Level the washing machine so that it is stable.

1. Level the washing machine by rotating the

adjustable feet using a No. 32 (1.26") spanner.

The feet allow levelling by +/- 1 cm (0.39").

2. After adjusting the height of the feet, ﬁrmly

tighten the jam nuts using a spanner No 17

(0.67"), by turning them towards the bottom of

the washing machine .

3. Tighten the jam nuts.

5 mm

5Set the dryer feet:

1. Tighten the front two feet all the way in.

2. Undo the back feet by 3.5 turns or 5 mm (0.2");

then, fasten the jam nuts towards the bottom of

the appliance .

6Place the dryer onto the washing machine:

1. Lift the front part of the dryer by 5 cm (2") to

10 cm (4").

2. Attach the vacuum feet onto the front feet of the

dryer.

3. Push the dryer into the tipping guard (so that

the B part is inserted into the A part) and

release it (See ﬁgure on previous page).

Make sure the tipping guard is "locked"!

6Customer Care Center, 1-800-898-1879, www.askona.com

CHANGING THE DOOR OPENING DIRECTION

To change the direction of door opening, proceed as follows.

1Open the door fully.

2Undo the screws and remove the door.

3Use the screwdriver to remove the door lock cover

and undo the screw on the door lock.

4Push the door lock upwards and remove it. Move

it to the other side and push it downwards.

5Fasten the screw on the door lock. Replace the

door lock cover.

Customer Care Center, 1-800-898-1879, www.askona.com

6Undo the door hinge assembly (left) and the door

latch assembly (right), switch their positions, and

replace the screws (door hinge assembly to the right-

hand side, door latch assembly to the left-hand side).

Use the screwdriver to remove the plastic part

more easily.

7Undo the door ring and remove it temporarily.

8Rotate the door glass cover by 90° so that the sign

indicating the opening of the door is on the other

side.

9Rotate the door ring by 180°, install it onto the

door, and fasten it with screws.

10 Replace the door on the door hinge and fasten

the screws.

8Customer Care Center, 1-800-898-1879, www.askona.com

BUILT-IN

4-1/2"

8-3/4"

222 mm

115 mm

30-1/3"

770 mm

ASKO dryers can be installed beneath a cabinet

or worktop with a minimum height of 34” (864 mm).

There must be a gap of about 1/2” (12 mm) all

around the machine, including between the rear

edge of the machine and the back wall. The opening

width must be at least 24-1/2” (622 mm).

The height adjustment for the dryer is 33-1/2” to

34-1/2” (850 mm to 876 mm). Do not raise it higher

than 34-1/2” (876 mm). Hole measurements are from

center of hole.

Closet Install- Ventilation Requirements

ASKO's front panel controls make it possible to

install the washers and dryers in a closet. Make sure

there is clearance between units and cabinet or wall

and a 1" (25 mm) minimum clearance between the

rear edge of the machine top panel and the cabinet

or wall. To ensure proper ventilation, we recommend

louvered doors. Otherwise there must be ventilation

openings in the door. See illustration for minimum

ventilation openings below (gray boxes):

Ensure the dryer door can be opened without

hindrance after installation.

The cool air intake panel at the front of the dryer

must not be blocked or covered. Doing so could

cause an error.

Customer Care Center, 1-800-898-1879, www.askona.com

AIR EXHAUST

The tumble dryer must only be operated when it

is correctly ﬁtted with exhaust duct.

Connecting the exhaust duct to the dryer

You will need to purchase a UL-CSA-approved

4" ridged metal exhaust duct. The dryer is delivered

with the stub pipe attached to the rear exhaust

outlet, though the exhaust duct can be attached to

either the left or the right exhaust outlet.

To connect the exhaust duct to the left or right side

outlet, follow the steps below:

1. Using a ﬂat-head screwdriver, turn the exhaust

outlet cover you plan to use to the right or left to

align the tabs holding the cover in place.

2. Remove the exhaust outlet cover.

3. Remove the stub pipe from the rear exhaust outlet

and place it in the outlet you plan to use.

4. Use the exhaust outlet cover you removed from

the to cover the rear exhaust outlet.

Asko dryers have a "T-style" exhaust

vent that allows you to connect the duct

on the rear, on the left, or on the right

side Vent

Stub Duct

(not supplied)

Clamp

(not supplied)

T-tube

Rear Exhaust

Outlet

Side Exhaust

Outlet

The duct must not be assembled with screws or

other fasteners that extend into the duct and catch

lint.

To connect the exhaust duct to the outlet, follow the

steps below:

• Push the duct onto the stub pipe and secure it

with a clamp.

• After you push the dryer into place, check for

kinks in the duct.

Excessive duct length and too many bends can

impede drying performance. We recommend that

you cut oﬀany excess exhaust duct and run the duct

with as few bends as possible. Make any necessary

bends as gentle as possible.

Maximum duct length of 60 feet. A maximum

of 4 elbows may be used, but 4 feet of duct must

subtracted from the total vent length for every 90°

elbow used.

To reduce the risk of ﬁre, this appliance must

be exhausted OUTDOORS or the equivalent. Never

cover the end of the dryer stub or exhaust duct with

anything to catch lint, except for UL approved vent

basket.

10 Customer Care Center, 1-800-898-1879, www.askona.com

Connecting to a ventilation duct

You will need a UL-CSA-approved, 4-inch ridged

metal exhaust duct. If a ﬂexible duct is used, it must

comply with the Outline for Clothes Dryer Transition

Duct. Subject 2158A and maximum length of 2.4 m

(8 feet).

The more bends and the longer the duct, the

less air will circulate through the machine, which

will impede drying performance. We recommend

that you cut oﬀany excess exhaust duct and run the

duct with as few bends as possible. And make any

necessary bends as gentle as possible.

Maximum duct length of 60 feet. A maximum

of 4 elbows may be used, but 4 feet of duct must

subtracted from the total vent length for every 90°

elbow used.

When installing in warm climates (77° F and

above) with high humidity levels, do not route the air

exhaust duct upwards.

Examples of installations

subtract 4 feet for

every 90° elbow

To connect the exhaust duct to a ventilation

outlet, follow the steps below:

1. Connect the exhaust duct to a ventilation exhaust

ﬁtting or to a discharge through the wall.

2. Secure the duct joint to the outlet stub on the

machine.

3. Run the duct with as few bends as possible to the

point of discharge.

Ventilation grill (not

supplied with machine)

This appliance shall not be exhausted into a

chimney, a wall, a ceiling, an attic, a crawl space

or a concealed space of a building. Only a rigid or

ﬂexible metal duct shall be used for exhausting. Only

a metal ventilation grill shall be used. If the duct is

taken to a wall outlet, a ventilation grill shall be ﬁtted

to prevent reverse ﬂow of cold air. Fit the ventilation

grill to the outside of the wall.

Avoid:

• very long exhausting systems

• too many corners

• tight corners

These reduce eﬃciency and increase time and

energy consumption.

Risk of Fire.

A clothes dryer produces combustible lint. The dryer

must be connected to an exhaust to the outdoors.

Regularly inspect the outdoor exhaust opening and

remove any accumulation of lint around the outdoor

exhaust opening and in the surrounding area.

Inhaltsverzeichnis

Andere Asko Trockner Handbücher

Asko

Asko T712C Bedienungsanleitung

Asko

Asko T744 Montageanleitung

Asko

Asko Classic T208H Leitfaden

Asko

Asko T701 Bedienungsanleitung

Asko

Asko T884XLHP Bedienungsanleitung

Asko

Asko DC7583 Bedienungsanleitung

Asko

Asko PEL D80 HP Bedienungsanleitung

Asko

Asko T700 Series Bedienungsanleitung

Asko

Asko T711 Kurzanleitung

Asko

Asko T408HD W Series Bedienungsanleitung

Asko

Asko TL751G XXL Bedienungsanleitung

Asko

Asko T721 Bedienungsanleitung

Asko

Asko PROFESSIONAL TDC112CS Bedienungsanleitung

Asko

Asko T712 Montageanleitung

Asko

Asko T411HSW Bedienungsanleitung

Asko

Asko T208VW Bedienungsanleitung

Asko

Asko TD75.13XX Bedienungsanleitung

Asko

Asko T720 Bedienungsanleitung

Asko

Asko T712C Bedienungsanleitung

Asko

Asko T712 Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Asko

Asko Professional TDC145HPS Bedienungsanleitung

Asko

Asko TD85.C38X Bedienungsanleitung

Asko

Asko T784C W Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Miele

Miele TWH 780 WP Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Bedienungsanleitung

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung