Assa Abloy SARGENT FM8700 Bedienungsanleitung

1-800-727-5477 • www.sargentlock.com A7827E 6/22

in whole or in part without the express written permission ofSARGENT Manufacturing Company is

prohibited. Patent pending and/or patent www.assaabloydss.com/patents.

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information go

to www.P65warnings.ca.gov.

FM8700, 12-FM8700

Surface Vertical Rod Exit Device

Installation Instructions

Top rod

Chassis

Chassis cover

Top case

Bottom rod

Bottom case

End cap bracket

End cap

Push rail assembly

THIS E XIT DE VICE IS HANDE D

Righthand

revers e bevel

OUT

Lefthand

revers e bevel

Interlocking

shim

FM8700, 12-FM8700

Installation Instructions Manual

Surface Vertical Rod Exit Device

part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

1-800-727-5477 • www.sargentlock.com A7827E 6/22

Pencil

Note: For all 12-FM8700 single door application, (4) thermal pins are required. See Template 4628 in Step 14.

Note: For rail lengths and cutting instructions, see Step10.

1Tools Required

Note: This device is one component of a specific combination of hardware required for this opening to meet FEMA

361 requirements. Follow all installation stepsas directed, in sequence given.

Hacksaw Clamp

File Lever Hammer

Drill Drill Bits:

#7, #16, #25,

3/32”, 1/4”,

11/32”,

3/8”, 25/64”, 3/4”,

Tape Measure #2 & #3 Phillips Head

Screwdriver

Taps:

10-24, #12-24,

1/4”-20

and 7/16” -20

Allen wrenches: 1/8", 3/16", 5/16", 3/8"

1-800-727-5477 • www.sargentlock.com

part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

A7827E 6/22

FM8700, 12-FM8700

Installation Instructions Manual

Surface Vertical Rod Exit Device

1Tools Required, continued

FASTENER CHART

1/4-20 CONCRETE SLEEVE ANCHORS

FM8700, 12-FM8700

Installation Instructions Manual

Surface Vertical Rod Exit Device

part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

1-800-727-5477 • www.sargentlock.com A7827E 6/22

2Door Preparation

1. Mark vertical reference line A. A is the centerline for the chassis, top and bottom cases.

2. Mark horizontal reference line B at 41" above the finished floor. B is centerline for the chassis and rail.

3. Tape top case and chassis templates to the door (packed with the device).

Finishedfloor

“A”

“B ”

41"

Inside

face of

door

5/8"

Max

1-800-727-5477 • www.sargentlock.com

part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

A7827E 6/22

FM8700, 12-FM8700

Installation Instructions Manual

Surface Vertical Rod Exit Device

3Install Top Bolt and Strike

1. Prepare cut-out in frame for 659 Top Bolt / Strike. Use 11/64" drill, 12-24 tap, #3 Phillips screwdriver.

2. Install 659 Top Bolt/Strike. Transfer vertical centerline to door frame. With the door closed, align the interlock-

ing shim with the 659 Top Bolt / Strike and place on vertical reference line. Mark and drill four mounting holes

using 11/64" drill and 12-24 tap.

3. Mount 659 Top Bolt/Strike, (4) #12-24 x 3/4" Phillips Head Flat H.D. machine Screws.

Note: All four fasteners required. Do not tighten until Step 5.

Frame Cutout

Top Bolt

659 Top Plate

Top bolt a s s embly in

frame, cut-away view

FM8700, 12-FM8700

Installation Instructions Manual

Surface Vertical Rod Exit Device

part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

1-800-727-5477 • www.sargentlock.com A7827E 6/22

4Install Top Case

1. With the door closed, center the Top

Chassis Assembly and Interlocking

Shim on the vertical reference line. The

Interlocking Shim must be engaged in

the Top Bolt/Strike.

2. Mark location of (4) mounting screws.

3. Use 3/8" Drill Bit to drill two Top Mount-

ing Holes through the door. Install (2)

sex nuts, p/n #60-0502 from the out-

side door surface. Install (2) 12-24 x 3/4

Socket Head Cap Screws from Inside.

4. Attach using (2) 12-24 x 3/4" Flat Head

Socket Head Screws in two bottom holes

(1/8" Allen Wrench).

5Securing Interlocking Shim

Top Chassis Assembly

(2) 12-24 x 3/4"

SocketHead Cap

Screws

(2) 12-24 x 3/4" F lat Head

SocketScrews

Top rod

Top ca se

Interlocking

Shim

Door Frame

Top P late

Top C a s e

Door S top

Interlock S him

1. With the Top Chassis Assembly and Interlocking

Shim secured, the 659 Top Bolt / Strike should

engage the Top Chassis Assembly and Interlock-

ing Shim when the door is closed.

2. Trace the outline of the Interlocking Shim.

3. Remove the Top Chassis Assembly to expose the

center hole on the Interlocking Shim. Ensure the

Interlocking Shim is aligned with the tracing.

Mark and tap center hole (1) 12-24 x 3/4" Flat

Head Socket Head Screw.

4. Reinstall Top Chassis Assembly.

5. Check for Top Chassis Assembly and 659 Top Bolt

/ Strike engagement. Tighten all screws.

6. Install Top Case Cover using (4) 8-32 x 5/16"

screws.

1-800-727-5477 • www.sargentlock.com

part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

A7827E 6/22

FM8700, 12-FM8700

Installation Instructions Manual

Surface Vertical Rod Exit Device

POSITION TRIM ON

DOOR - Align spindle

with BE LL HOUS ING

THRU-BOLT CHASSIS

to E T T R IM with

(2) 1/4" -20 x 2 3/8"

PH.FL.HD.Mach. Screws

Chassis

Bell housing

6Install Center Chassis

1. Secure Chassis and Chassis Shim with (4) #10-24 x 3/4" Phillips Head Flat H.D. Machine Screws, 4 corner

mounting holes.

Note: Use all four screws provided.

7Rail Shim Lengths and cutting Instructions

1. Refer to rail size listed on the box the device was shipped in. Break Rail Shim to the length that corresponds to

the rail size.

Note: If shim needs to be cut, always cut shim from the end closest to the hinge edge.

Rail S izes

Use Breaking Lines to shorten S him to the needed Rail size

FM8700, 12-FM8700

Installation Instructions Manual

Surface Vertical Rod Exit Device

part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

1-800-727-5477 • www.sargentlock.com A7827E 6/22

653 Bottom Strike

Panic & Fire Rated

653 Strike

8Install Rail

1. Level rail assembly on door. Use rail

assembly as template. Mark and punch

locations for threaded holes.

2. Remove rail assembly from door.

3. Drill and tap (2) holes as shown in door

surface (#7 drill, 1/4-20 tap, 25/64" drill,

7/16-20 tap).

4. With rail shim under the mount install

push rail assembly on to door.

5. Install shoulder and socket head screw

(3/16" wrench for 1/4"-20 bolt, 3/8"

wrench for 7/16" screw).

Note: Do not install through-bolts until installation is complete and all mounting screws are tight. Do not install

chassis cover at this time.

Touch Pad Ins ert

Touch Pad Ba se

ShoulderScrew

(1/4- 2 T HD)

Insert PushRail Clearance

Hole 2

P us h R a il A s s embly

Rail to Chassis screw

Three Screw

and Washer

Assemblies

Clearance

Hole 1

SocketHead CapScrew

7/16" - 20 x 1/2"

1. Attach touch pad base to push rail with (3) screw and washer assemblies.

2. Snap touch pad insert into touch pad base.

3. Install End Cap Bracket. Attach to door using (2) #10-24 x 3/4" Phillips round head machine screws.

4. Tighten all screws. Install hinge side cover using (2) #8-32 x 5/16" Phillips oval head machine screws.

9Install Bottom Strike

Surface Mount 653 Bottom

Strike

1. Transfer vertical centerline to

threshold.

2. Drill holes 1 5/8" to 1 3/4" deep for

(3) 1/4" sleeve anchors.

3. Disassemble anchors and drop

lower portion into hole with

threads towards top of hole.

4. Align holes in strike with holes in

floor.

5. Screw top half of anchor onto the

installed piece through the holes

in the strike. Tighten anchors

securely.

Note: No Clearance in floor is required.

(3) #1/4-20 x 2" Sleeve Anchors

(3) 01-9679 Sleeve Anchors

1-800-727-5477 • www.sargentlock.com

part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

A7827E 6/22

FM8700, 12-FM8700

Installation Instructions Manual

Surface Vertical Rod Exit Device

10 Install Bottom Case

Top Mounting

Holes (2) 68-1663 sex nuts

Bottom

Mounting

Holes 1/8" MAX gap

between case

and strike.

5/8" undercut

INSIDE

DOOR

SURFACE

OUTSIDE

DOOR

SURFACE

1. Using the vertical reference line, with bottom

case as a template, Align Bottom Case for 1/8"

maximum gap between case and strike.

2. Drill and tap top mounting holes for

(2) 12-24 x 3/4" flat head socket screws, using

11/64" drill and 12-24 Tap.

3. Use 3/8" drill bit to drill two bottom mounting

holes through door.

4. Install (2) sex nuts, p/n 68-1663 from outside

door surface.

5. Install (2)12-24 x 3/4 socket head cap screws

from inside.

6. Tighten Screws with a 1/8" Allen wrench, for

the top and 5/32" Allen wrench, for the bot-

tom.

11 Install Rods

1. Slide top rod into main slide, center chassis, until

center hole is aligned with the hole in the main

slide.

2. Thread top rod into top caseuntil finger-tight.

3. Adjust position and insert rod adjustment pin.

4. Slide bottom rod into main slide, center chassis.

5. Thread bottom rod into bottom case until fin-

ger-tight.

Rotate to adjust height.

6. Unscrew bottom rod until the center hole is

aligned with the bottom slot in the main slide.

7. Insert rod adjustment pin.

Rod adjustment pin

BOTTOM ROD / CENTER CASE

TOP ROD / CENTER CASE

FM8700, 12-FM8700

Installation Instructions Manual

Surface Vertical Rod Exit Device

part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending

and/or patent www.assaabloydss.com/patents.

1-800-727-5477 • www.sargentlock.com A7827E 6/22

12 Adjust Top & Bottom Rods

Adjust top and bottom latch bolts for maximum engagement.

Rough adjustments are made by changing the hole used for the adjustment pin.

For Fine adjustments: Turn rod into top and bottom cases to shorten, or turn rod out of top and bottom

cases to lengthen.

Top Rod: Push on the door and the rail at the same time. As soon as the door opens, release the rail. The

top bolt should be in the hold back position. If not, extend the top bolt.

Note: Top bolt must go into hold back position before the door opens.

Bottom Rod: Extend the bottom bolt for maximum engagement with bottom strike.When the top bolt is

in hold back, it also holds the bottom bolt in the retracted position. When the bottom bolt is retracted,

the bolt must clear the bottom strike by 1/8" minimum through the swing of the door.

When adjustment is completed, install top and bottom rod guides at midpoint between center and top

and bottom chassis, using (2) #10-24 x 1-1/4" oval head screws per guide.

Install center chassis cover using (4) #8-32 x 5/16" screws.

13 Rail Lengths & Cutting Instructions

RAIL MAX DOOR WIDTH MIN DOOR WIDTH

E 32" 24"

F 36" 33"

TOP VIE W OF E XIT DE VICE

F or doors with s tile, the rail mus t

overlap s tile by 1/2" or more

Vertical reference line

Lof chassis)

1-3/4" min.

“X”

“Y ”

Cutoff mark

Determine rail leng th dimens ion “X” by s ubtracting

1-3/4" from dimension “Y”.

1. Dog push rail and cut off at mark.

2.Cutmustbestraight.

3. F or (43-) flush end cap use cutting

guide provided.

4. R emove s harp edges with file.

Dieses Handbuch passt für folgende Modelle

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy SARGENT 278 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Pull Side Series Kurzanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 855 Montageanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5400 (A) Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7900H-B Series Bedienungsanleitung

Assa Abloy

Assa Abloy Rixson Smok-Chek VI Kurzanleitung

Assa Abloy

Assa Abloy 332 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC700G-E Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7970DPS-B Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent FIREGUARD 2408 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron EEB3N Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy RD3 Bedienungsanleitung

Assa Abloy

Assa Abloy DC640 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 78-B/FHA Hold Open Series Bedienungsanleitung

Assa Abloy

Assa Abloy 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5700 Series Kurzanleitung

Assa Abloy

Assa Abloy DC 700G-FT BGS Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON 91DCP Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung