Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

FM574 01/23

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Available on the following devices:

Rim

Mortise

Concealed Vertical Rod

*Surface Vertical Rod

*Rod Guards Required (made by other manufacturers)

PED4000 D, PED5000 D Series Exit Device

Premium Delayed Egress

Installation Instructions

Premium Delayed Egress

Installation Instructions

PED4000 D, PED5000 D Series Exit Device

FM574 01/23

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

TOC Table of Contents

1 Panic and Fire Rated Devices.....................................................4

a Checklist ........................................................................4

b Required Components ..........................................................4

c Optional Components ...........................................................4

d Electrical Specifications..........................................................4

2 Insert and PC Board Assembly ...................................................5

3 DIP Switch Settings ..............................................................6

4 Device Mounting ................................................................8

5 Wire Routing .................................................................. 10

6 Installation of Insert Asssembly to Device ...................................... 21

7 Harness Wiring Reconfiguration ............................................... 22

8 Input/Output Connector Designations ......................................... 23

9 ElectroLynx System ............................................................ 26

10 ElectroLynx Wiring Options Overview with QC12 Hinge........................ 27

11 System Wiring Examples ElectroLynx QC8 Hinge ............................ 28

12 System Wiring Examples ElectroLynx QC12 Hinge ........................... 30

13 Field Wiring Door Prep ........................................................ 32

14 Operating Instructions......................................................... 33

15 Additional Options Non ElectroLynx Wiring.................................... 34

Premium Delayed Egress

Installation Instructions

FM574 01/23

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

PED4000 D, PED5000 D Series Exit Device

TOC Table of Contents

16 BOCA 15 Second Delay BC-59_ & BOCA 30 Second Delay BC-59_ ............... 34

17 NFPA 101 Requirements: 30 Second Delay BC-59_ Suffix ....................... 34

18 Troubleshooting............................................................... 35

Caution: Do not change factory applied finishes.

NOTE:

• Wiring method must be in accordance with CSA C22.1, Canadian Electrical Code, Part I, Safety Standard for

Electrical Installations, Section 32; and CAN/ULC-S524 Installation of Fire Alarm Systems.

WARNING

This product can expose you to lead which is known to the state of California to cause cancer and birth defects

or other reproductive harm. For more information go to www.P65warnings.ca.gov.

Premium Delayed Egress

Installation Instructions

PED4000 D, PED5000 D Series Exit Device

FM574 01/23

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

1Panic and Fire Rated Devices

1. Check device for shipping damage prior to installation and make sure all parts are on hand.

2. Identify options provided with device.

3. Identify model, type and hand of trim if applicable (see exit device and trim instructions for reversing hands).

4. Contact hardware supplier if device is damaged or missing parts.

aChecklist

bRequired Components (Numbered list correlates with numbers in Figure 1)

cOptional Components (Numbered list correlates with numbers in Figure 1)

1. 24VDC UL Listed Regulated and Filtered Power Supply with Fire Alarm Interface (recommend Securitron BPS 24-1 or

24-2 (UL294 Listed), depending on requirements). Power supply is NOT to be used in UL603 Burglar Alarm System.

2. Power transfer UL or ULC listed (8 or 12 wire depending on system) ElectroLynx QC8 or QC12, Securitron (EPT) or

equivalent.

3. Sign (MUST BE INSTALLED ON DOOR ABOVE DEVICE).

NOTE: The delayed egress system is to be installed in accordance with NFPA 101.

dElectrical Specifications*

• Input Voltage: 24VDC +/- 15% (20.4 - 27.6VDC)

regulated/filtered

• Power Consumption @ 24VDC:

60 - 70 mA (typical) Disarmed

280 -340 mA (typical) Armed

320 - 830 mA (typical) Delayed Egress Initiated

70 - 90 mA (typical when arming)

Output Relays: Form C, 1 Amp 24VDC

Operating Temp: -40°C to 66°C (-40°F to 150.8°F)

*Follow Local Electrical Codes for Wiring.

NOTE: Components shown do not reflect all possible applications. Refer to other system wiring diagrams within

this manual. Consult manufacturer for special applications.

Figure 1

PUSH UNTIL ALARM

SOUNDS. DOOR CAN BE

OPENED IN 15 SECONDS.

115 VAC

800 mA

60 Hz

Fire

Alarm

Circuit

Req’d

4. Remote Annunciator

5. Door Position Switch (DPS)

6. Standard Trim

7. Electrified Trim

8. Device and Trim Cylinder

Premium Delayed Egress

Installation Instructions

FM574 01/23

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

PED4000 D, PED5000 D Series Exit Device

Figure 2

Cylinder Nut

Activator Leg

Circuit Board Assembly

Indicator Light (LED)

Arming Switch Activator

Lens Cover

1-1/8” (29mm) Mortise

Cylinder 1000-118-A07

(Order seperately)

Order Separately

1-1/8”

29mm

A07 Cam

Assembly steps for non-factory-keyed orders:

1. Insert cylinder through the cylinder support piece in the rail insert with keyway

horizontal and toward the closest end of the rail insert.

Typical Mortise Cylinder

1000-118-A07

3. Secure parts in place with cylinder nut. Be certain arming switch activator sits around flange in the cylinder

support piece to allow rotation of activator.

4. Insert circuit board assembly into rail insert over cylinder and switch activator. Ensure the fingers of the arming

switch activator straddle the switch mounted to the circuit board. Press down until it snaps into all four slots in the

rail insert.

5. Verify assembly by rotating key counter-clockwise and clockwise. Key should move freely and arming switch should

trip for both rotation directions. If key does not rotate freely, verify arming switch activator is properly seated on

cylinder support piece.

2. Slide arming switch activator over cylinder and onto the cylinder support piece. Notch in arming switch activator

keys over the stop feature in cylinder support.

Cylinder and Collars

• Use standard 1-1/8” mortise cylinder

with A07 cam, no collar. Corbin

Russwin #1000-118-A02 collar is not

required.

• Use Corbin Russwin spacer 370F29 for

optional 1-1/4” long cylinder.

• Use Corbin Russwin spacer 370F31 for

optional 1-1/2” long cylinder.

P5 connector - Plug this into

the end bracket’s metal tab

P1 P2

Figure 3

2 Insert and P.C. Board Assembly

Premium Delayed Egress

Installation Instructions

PED4000 D, PED5000 D Series Exit Device

FM574 01/23

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 Insert and P.C. Board Assembly, continued

NOTES:

• Factory keyed orders will be shipped assembled.

• Prior to insert assembly, device must be cut to proper length to prevent damage to circuit board - 36" device cannot

be field cut. A maximum of 6" can be cut from a 48" device.

1 Nuisance Audible

2 Nuisance Delay

8 DPS Bypass

3 Nuisance Delay

4 Reset Delay

5 Reset Delay

6 Armed LED Color

7 RAC

3DIP Switch Settings

S2-1: Nuisance Audible may be selected ON (default) or OFF

PCBA DIP SWITCH VIEW

S2-8: Switch must be set ON (default) to Bypass when an external

Door Position Switch (DPS) is NOT used, and OFF when an

external DPS is used.

S2-2 and S2-3: Nuisance Delay time may be selected 0 (Immediate),

1 (default), 2 or 3 seconds

S2-4 and S2-5: Reset Delay time may be selected 5, 10 (default), 20 or

40 seconds

S2-6: Cover Armed LED Color is Red (default) when ON and Green when OFF

S2-7: Re-arm After Closing (RAC)* (see below)

S2 Dip Switch - Default Settings

S2 Dip SW 1 2 3 4 5 6 7* 8

OFF (UP) OFF OFF OFF

ON (DOWN) ON ON ON ON ON

Premium Delayed Egress

Installation Instructions

FM574 01/23

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

PED4000 D, PED5000 D Series Exit Device

Nuisance Delay (seconds)

0 1 2 3

S2-2 OFF OFF ON ON

S2-3 OFF ON OFF ON

Reset Delay (seconds)

5 10 20 40

S2-4 OFF OFF ON ON

S2-5 OFF ON OFF ON

S2-6 OFF Cover Armed LED Color is Green

ON Cover Armed LED Color is Red (default)

S2-7 OFF* Momentary egress mode 5, 10, 20 or 40 seconds. Device will immediately

Rearm After Closing (RAC) door, if closed before selected time expires or

it will enter alarm mode, if time expires with door open (default).

See other details*

ON** 40 seconds momentary egress mode is extended indefinitely, if the door

is left open. Then the device immediately Rearms after Closing (RAC)

door. See other details**

S2-8 OFF External DPS is wired to device

ON DPS Bypass, external DPS is NOT wired to device (default)

3DIP Switch Settings, continued

*With S2-7 OFF (S2-4 and S2-5 set for 5, 10, 20 or 40sec), if door/DPS is open after selected time the alarm will sound. Close door to

reset and rearm device using cylinder key or remote reset signal.

**S2-7: When an external DPS is used and switch S2-7 ON, and 40 second reset delay (S2-4 and S2-5) are set ON, after activation of

momentary egress by cylinder key switch or external remote reset signal, if the Door/DPS is open beyond 40sec the device will remain

in momentary egress mode indefinitely and shall not enter alarm mode; then once the Door/DPS is closed it will rearm immediately.

If door/DPS is opened then closed before selected time expires, the device will rearm immediately.

If DPS is not used, is bypassed with S2-8 ON, the door will rearm immediately after 5, 10, 20 or 40 sec whether the door is open or

closed, with either S2-7 ON or OFF.

Ensure eight S2 Dip Switches are set per application before moving on to the next page of instructions.

Default

Premium Delayed Egress

Installation Instructions

PED4000 D, PED5000 D Series Exit Device

FM574 01/23

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

4Device Mounting

1. Refer to installation instructions included with device and trim for complete door and frame preparations. Refer to

template for wire access hole location.

2. Feed wires from power transfer through wire access hole in door. (Figure 4)

ElectroLynx System Default Wiring Options for DEED QC12 Hinge (12 wires)

Pluggable 8-pin & 4-pin connectors. Default wiring shown.

3 1

4-pin

8-pin

Rail to Hinge Harness

(with 8-pin, 4-pin, & 26-pin connectors )

ElectroLynx Field

Wiring Termination

Options

(12 wires max)

8, Yellow (RAR NC)

4, Tan (SEC NO) QC12 HingePremium Delayed Egress

Rail Assembly

Door Harness

3" Typical

QC12 Hinge Pigtail

15' Frame Harness

26-pin

Must connect to metal tab

on exit device end bracket

Door Harness

3" Typical

QC12 Hinge

QC12 Hinge Pigtail

15' Frame Harness

Premium Delayed Egress

Device

Pluggable 8-pin and

4-pin connectors

(RAR COM)

(SEC COM)

VDC

(EI)

(RAR COM)

8, Yellow (RAR NC)

(SEC COM)

4, Tan (SEC NO)

NOTES:

• Wires must be protected from abrasion.

• For use with Class II circuits only.

Figure 4

Premium Delayed Egress

Installation Instructions

FM574 01/23

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

PED4000 D, PED5000 D Series Exit Device

4Device Mounting, continued

7. Do not install end cap until device has been wired and tested for operation (See wiring diagrams).

Figure 3

3 When required, mount outside trim to door

(see trim installation instructions).

4. Unthread screw and remove dogging slope bracket (Figure 3).

5. Pull the mount rail cover back to expose front end of the carrier/push

assembly (Figure 4).

6. Install chassis on door. Leave chassis screws loose. Insert rail onto chassis. Pin bracket to slot in chassis lift arm

(Figure 5).

7. Slide the mount rail back to the front and replace the dogging slope bracket and screw (Figure 6).

Figure 5

Figure 4

Figure 6

Note: For additional instructions on hardware install, refer to

mechanical instructions.

Premium Delayed Egress

Installation Instructions

PED4000 D, PED5000 D Series Exit Device

FM574 01/23

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

5Wire Routing

PED4600

OVERVIEW

M91 Connection

Step 1. Install mortise lock. Route wire

as shown.

M93 Lever Monitoring

(if applicable)

M91 Connection

Electric Trim

(If applicable)

Step 2. Route trim wires as shown.

M93 Lever Monitoring

(if applicable)

Electric Trim

(If applicable)

Electric Trim

(If applicable)

M91 Connection

M93 Lever Monitoring

(if applicable)

Step 3. Install chassis and rail.

Make wire connections.

Step 4. Pull back excess wire

through rail. Route wires as

shown. Install wire clip.

Wire Clip

Andere Handbücher für Corbin Russwin PED5000 DB Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Norton 9510 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON 185 Quick Spotter Bedienungsanleitung

Assa Abloy

Assa Abloy DC140 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9540 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 351 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW200 Handbuch

Assa Abloy

Assa Abloy effeff 828 Bedienungsanleitung

Assa Abloy

Assa Abloy Pando Mini Go Bedienungsanleitung

Assa Abloy

Assa Abloy DC 700G-FT BGS Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY DA401 Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON W73ER Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6000 Series Installationshandbuch

Assa Abloy

Assa Abloy Norton 7570 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC700G-FT Bedienungsanleitung

Assa Abloy

Assa Abloy King 640 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED8200A Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SP33-M Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 351 Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC200 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung