Assa Abloy Aperio Series Bedienungsanleitung

Page 1 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Products Specifications

Wireless Frequency: 2.4GHz, IEEE 802.15.4, using AES 128-bit encryption

Lock Battery Type: AA Lithium, 1.5 Volts (V)

Battery Life: 50,000 cycles*

*All battery life claims are approximate and based on a set configuration profile. Battery performance is based on pre-defined system settings such

as battery chemistry and battery model used, credential presentation settings (LED/buzzer), UHF polling period, UHF status intervals, and

operations per day. Actual battery performance will vary and depends on the factors above.

Operating Temperature: 32to 122F (0to 50C)

HID® multiCLASS SE® technology Credentials Supported:

High Frequency (13.56 MHz):

HID iCLASS®

HID iCLASS SE®(SIO-enabled)

HID iCLASS®Seos™

HID MIFARE®SE

HID DESfire®EV1 SE

MIFARE CLASSIC

DESfire®EV1

Low Frequency (125 kHz):

HID Prox®, AWID, EM4102, ioProx

NFC-enabled Mobile Phones

AA Lithium Batteries

required. Use of other

types of batteries, such as

alkaline, will significantly

decrease battery life.

HES K100 AperioSeries

Wireless Cabinet Lock

Installation and Operating Instructions

Page 2 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Recommended Tools

Flathead Drivers —3/32”, 3/16”

Drill, Drill Bits —1/16”, 3/16”, 1/2”

Phillips Drivers —P0, P2

Pencil, Wire Stripper, Level, Square, Ruler, Punch, Scissors

Hardware Specifications

Table 1 –Shaft Length

Table 2 –Mounting Screw Length for Various Door Thickness

Door

Thickness

Reader

Mounting

Cut to

approx.

screw

length

Lock

Mounting

Cut to

Approx.

Screw

Length

1/16”

Coupling Nut

and 3” Rod

10/16”

8-32 x 1-3/4”

Break Away

1-1/16”

1/4"

Coupling Nut

and 3” Rod

13/16”

8-32 x 1-3/4”

Break Away

1-1/4”

1/2”

Coupling Nut

and 3” Rod

1-1/16”

8-32 x 1-3/4”

Break Away

1-7/16”

3/4”

Coupling Nut

and 3” Rod

1-5/16”

8-32 x 1-3/4”

Break Away

No Cut

1”

Coupling Nut

and 3” Rod

1-9/16”

8-32 x 2-1/2”

2”

1-1/4”

Coupling Nut

and 3” Rod

1-13/16”

8-32 x 2-1/2”

No Cut

1-1/2”

Coupling Nut

and 3” Rod

2-1/16”

8-32 x 2-3/4”

No Cut

For Technical Support Please call 1-800-810-WIRE

Door Thickness

Shaft Used

1/16” – 1/2”

>1/2” – 1½”

>1½” – 2¼”

Page 3 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Package Contents

6 X 1/2"

(D)

6-32 X 5/16”

(C)

8-32 X 5/16”

(B)

2-56 X 7/16”

(A)

Reader

Lock Body

Strike Plate

Installation

Template

Mechanical Key Override

Hardware

8-32 X 2-1/2”

(G)

8-32 X 2-3/4”

(E)

8-32 X 1-3/4”

(F)

Lithium Batteries

Double Door

Bracket

8-32 X 3”Rod

(H)

8-32 Nut

(J)

Threadlock

Pillow Pack

Page 4 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Lock Orientation Options

Prepping the Cabinet/Drawer Face

1. Separate Strike Plate Template.

2. Establish centerline (for double door

cabinet prep go to page 6).

Orientation A

Orientation B

Orientation C

Page 5 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

3. Measure cabinet wall thickness and mark

offset line on face of cabinet/drawer. The

offset line should match with the interior

edge of the cabinet wall.

4. Continue centerline to face of

cabinet/drawer

5. Align template to offset line and

centerline. Remove backing and apply

template onto cabinet/drawer face.

6. Use punch to mark drilling

locations then drill mounting holes. If

using mechanical key override, drill

key override hole as well.

Center

line

Offset Line

Page 6 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Prepping the Cabinet/Drawer Face (Double Door)

3. Align offset line on template to the edge of the stationary door and align center

line with the established center line above. Remove backing and apply template to

cabinet face. Continue with Step 6 in previous section.

1. Establish center line on inside

of stationary door.

2. Continue center line onto

outside face of cabinet.

Page 7 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Reader Installation

1. Align reader with mounting holes and pull

cable through as shown. Trim Threaded rod

to length as outlined in table 2.

2. Add Threadlock to threaded rod.

Secure Reader to cabinet/drawer using

the cut threaded rod and coupling nut.

DO NOT overtighten.

Mechanical Override (Optional)

1. Slide Override into slot as shown.

2. Ensure that override retracts latch

bolt before installation. Override

should rest loosely until lock body and

battery cover are installed.

Page 8 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Lock Body Installation

1. Insert reader cable through hole

in back of lock body.

2. Align lock body to mounting holes

andsecure to cabinet/drawer face using

2x screw F and 2x screw D. If thick

cabinet/drawer then use 2x screw E or

2x screw G instead of 2x screw F. DO

NOT over tighten.

3. Plug cable into slot on lock body.

4. Tuck excess cable into lock body

cavity as shown.

5. Any excess cable should be inserted

into the cavity as shown below.

6. For cabinet/drawer face thicker

than1/2”, add a third screw D as

shown.

Page 9 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Installing the Batteries

1. Install AA lithium batteries in appropriate

position.

2. Install cover and secure using 2x

screw A.

Mechanical Key Override (Optional)

Mechanical key override cam lock sold

separately.

1. Insert cam lock through the outside

of the cabinet/drawer face and secure

with locking nut. Insert the end of Cam

into the mechanical override and secure

with nut as shown.

Important Note–Reader MUST be programmed before installing the strike plate. If the cabinet

is closed before the reader is programmed and after the strike plate is installed, you will be locked out of

the cabinet.

Page 10 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Strike Plate Installation

1. Align strike plate template to centerline

and edge of cabinet. Drill mounting holes.

2. Secure strike plate to inside cabinet

wall using 2x screw D, but do not fully

tighten. Adjust strike plate so the edge

is flush with the cabinet wall edge then

tighten.

3. After the strike plate is in the desired position, fasten screw D into strike plate as

shown below.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy Aperio KS100 Bedienungsanleitung

Assa Abloy

Assa Abloy CLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL648 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT FM7300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy HES 8500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy IKON eCLIQ N111 BA3 Bedienungsanleitung

Assa Abloy

Assa Abloy 813C-50 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin FE6800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 9338 Leitfaden

Assa Abloy

Assa Abloy Yale Real Living B1L Z-Wave Technische Daten

Assa Abloy

Assa Abloy SARGENT Profile v.G1.5/LK Bedienungsanleitung

Assa Abloy

Assa Abloy EL410 Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood Optimum Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent KP Series Installationshandbuch

Assa Abloy

Assa Abloy Sargent SN Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 ML20600 Bedienungsanleitung

Assa Abloy

Assa Abloy K100-622 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Easy Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 8800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem 319N Montageanleitung

Assa Abloy

Assa Abloy ML20900 Series Bedienungsanleitung

Assa Abloy

Assa Abloy High Security Deadbolt 6000 Bedienungsanleitung

Assa Abloy

Assa Abloy HES KS200-640 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale nexTouch NTM 610 Montageanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung