Assa Abloy Corbin Russwin FE6600 Series Bedienungsanleitung

Installation Instructions

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

FM440 03/20

IMPORTANT:

Latches, rods, and cassette are pre-installed.

This product must be installed by a factory trained technician.

FE6600 and

BL6600 Series

Multi-Point Lock

FE6600 and BL6600 Series

Installation Instructions

Multi-Point Lock

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

FM440 03/20

TOC Table of Contents

1 Package Contents ...............................................................4

2 Tools Required ..................................................................5

a Tools Required for Electronic Access Control Shield ..............................5

b Tools Required for Dogging Indicator Option.....................................5

3 Installation ......................................................................6

a Check Door......................................................................6

b Door Installation ................................................................6

c Install Top Strike Into Door Frame................................................6

d Install Center Strike Into Door Frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

e Remove Retractor Inserts........................................................7

f Check Latches (Uninstalled).....................................................7

g Install Bottom Strike.............................................................8

h Top and Bottom Latch Adjustment............................................. 10

i Mortise Lock Install ............................................................ 12

j Final Mortise Lock and Trim Installation ........................................ 13

k Electronic Access Control (EAC) Reader and Controller Installation ............. 13

l Deadbolt Label Installation (FE6600 Only) ..................................... 13

m Key Override With Deadbolt Function Operation Check........................ 13

n Electronic Access Control (EAC) Shield (if applicable)........................... 14

FE6600 and BL6600 Series

Installation Instructions

Multi-Point Lock

FM440 03/20

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

4 Optional Installation........................................................... 14

a Dogging Indicator Installation ................................................. 14

5 Addendum .................................................................... 17

a Check Door.................................................................... 17

b Place Door Horizontal on Sawhorse............................................ 17

c Install Lockbody Cassette ...................................................... 18

d Latch Rod Guides .............................................................. 18

e Feed Top Rod Into Door........................................................ 19

f Align with Lockbody Cassette (LBC) ............................................ 19

g Troubleshoot Latch Installation ................................................ 20

h Correct Rod Installation Check................................................. 20

i Secure Top Latch .............................................................. 21

j Tighten Set Screw ............................................................. 21

k Bottom Latch Installation...................................................... 22

l Check Latch ................................................................... 22

m Mortise Reinforcer and Mortise Lock Installation ............................... 23

FE6600 and BL6600 Series

Installation Instructions

Multi-Point Lock

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

FM440 03/20

1 Package Contents

Part Number Description

1 82-5342 Multipoint cassette

2 82-5345 Trim mounting screw pack

3 82-5346 Top/bottom case mounting screw pack

4 82-5347 Top strike pack

5 82-5348 Bottom strike pack

6 82-5349 Mortise mounting/reinforcement pack

7 82-5350 Center strike pack

82-5351 IN/PN Inside cover shield pack

82-5352 Harmony inside cover shield pack

82-5353 Passport inside cover shield pack

9 188 Dogging indicator (includes item 13) (specify finish)

10 82-5383 Screw retainer pack

11 82-5386 Top case and rod assembly (specify door size)

12 82-5387 Bottom case and rod assembly (specify door size)

13 82-5400 Dogging indicator screw pack (specify finish)

14 01-4597 T-wrench, adjustment

15 Consult factory Outside armor front

16 Consult factory Mortise lock

17 Consult factory Mortise trim

18 Consult factory Cylinder

Note:

The grayed parts are pre-installed by

the door manufacturer and relate to the

Addendum section beginning on page 17.

FE6600 and BL6600 Series

Installation Instructions

Multi-Point Lock

FM440 03/20

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 Tools Required

Tape measure Hammer Flashlight 1/8" Allen

(supplied)

3/32" Allen

(supplied)

5/32" Allen

Drill 1/8" Masonry

drill bit

#3 Phillips

bit

Slotted

screwdriver

#1, #2, #3

Phillips head

screwdrivers

Chisel 3/8"

Anchor set

a Tools Required for Electronic Access Control Shield

#29 Drill bit

(.136")

#8-32 Tap

b Tools Required for Dogging Indicator Option

#7 Drill bit

(.201")

82° Countersink

FE6600 and BL6600 Series

Installation Instructions

Multi-Point Lock

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

FM440 03/20

3 Installation

a Check Door

Verify door is:

• Correct size and hand for opening.

• Correctly prepared to Template 4740.

IMPORTANT:

If measurement is incorrect, DO NOT PROCEED

WITH INSTALLATION. Contact door manufacturer.

(Figure1)

b Door Installation

Hang door on frame.

IMPORTANT:

If door rubs along floor, DO NOT PROCEED WITH

INSTALLATION. Contact door manufacturer.

c Install Top Strike Into Door Frame

• Remove the strike filler plate and screws and discard.

• Install four (4) #12-24 socket cap flat head screws. (Figure2)

Figure1

Door Height

Door Width

of Lockbody

Outswing Door

Shown

± 5/64"

39-9/16"

(101.4 cm)

Figure2

FE6600 and BL6600 Series

Installation Instructions

Multi-Point Lock

FM440 03/20

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3 Installation (cont.)

d Install Center Strike Into Door Frame

Install two (2) ¼-20 socket cap flat head screws. (Figure3)

e Remove Retractor Inserts

WARNING:

The door now has ability to latch. (Figure4)

f Check Latches (Uninstalled)

1. Insert uninstalled outside mortise trim and

rotate to verify top and bottom latches retract

flush with door. Do not install mortise trim at

this time. (Figure5)

2. Move top strike back and forth until top latch engages strike. (Figure6)

Figure3

Figure4

Figure5

TOP OF DOOR FRAME

Figure6

FE6600 and BL6600 Series

Installation Instructions

Multi-Point Lock

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

FM440 03/20

3 Installation (cont.)

g Install Bottom Strike

1. Close door and mark location of bottom bolt.

3/8" MAX

Bottom of door

to floor.

✓

Figure7

2. Open door and place strike over bottom bolt location.

3. Mark location of bottom strike pocket and hole locations. (Figure7)

Note:

Strike is not symmetric. Install as shown. If needed, strike can be rotated later to increase bolt clearance.

(Figure8)

Door Swing

Jamb

Narrow

Wide

Bottom Strike Pocket

Figure8

FE6600 and BL6600 Series

Installation Instructions

Multi-Point Lock

FM440 03/20

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3 Installation (cont.)

g Install Bottom Strike (cont.)

Flush Mount (Figure9)

Mortise strike 1/4" deep into floor.

(Optional for 3/8" door to floor gap.)

IMPORTANT:

Use a vacuum or compressed air to

clear holes ofdebris. (Figure10)

Cross Sectional View

Flush Mount (Figure11)

Surface Mount (Figure12)

Drill two (2)

3/8" diameter holes

by 2-1/4" deep.

Chisel the bottom strike pocket

1" deep to ensure the bolt has

full projection.

Figure12

IMPORTANT:

Use a vacuum or compressed air to

clear holes ofdebris. (Figure13)

Cross Sectional View

Surface Mount (Figure14)

2 1/4"

Figure14

Drill two (2)

3/8" diameter

holes by 2-1/4" deep.

Chisel the bottom strike

pocket 1" deep to ensure

bolt has full projection.

1/4" DEEP

Figure9

Use the anchor tool

to set anchors.

Figure10

2 1/4

Figure11

Use anchor tool

to set anchors

Figure13

FE6600 and BL6600 Series

Installation Instructions

Multi-Point Lock

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

FM440 03/20

3 Installation (cont.)

h Top and Bottom Latch Adjustment

1. With door hung, measure clearance between

top and bottom bolts and strikes. (Figure15)

Note:

If both measurements equal 1/16", proceed

to Step 3i, otherwise proceed with Step 3h as

follows:

2. Remove mortise filler cap and discard.

(Figure16)

3. Retract latches by rotating lever and opening

door. (Figure17)

Figure17

4. Using supplied 1/8" Allen wrench, loosen set

screw 1/4 turn maximum. This allows hex

rods to rotate during latch bolt adjustment.

(Figure18)

Figure15

1/16" Bolt to strike clearance.

TOP OF DOOR

1/16" Bolt to strike clearance.

BOTTOM OF DOOR

Figure16

Note location

of set screws.

Figure18

Andere Handbücher für Corbin Russwin FE6600 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy SECURITRON MORTISE UNLATCH MUNL-12 Bedienungsanleitung

Assa Abloy

Assa Abloy APERIO P100 Handbuch

Assa Abloy

Assa Abloy Yale P113 Bedienungsanleitung

Assa Abloy

Assa Abloy Bolt ASSA 560/13 Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron M38 Series Bedienungsanleitung

Assa Abloy

Assa Abloy ELECTRIC LOCK Bedienungsanleitung

Assa Abloy

Assa Abloy Cabinet Lock Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YM Series Bedienungsanleitung

Assa Abloy

Assa Abloy 840C-50 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin IN100 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL590 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff EX118R Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 9338 Leitfaden

Assa Abloy

Assa Abloy Yale 7370 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Assure Lever YRL216 Montageanleitung

Assa Abloy

Assa Abloy ABLOY EL574 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent KP Series Installationshandbuch

Assa Abloy

Assa Abloy Lockwood 3579 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 8200 Bedienungsanleitung

Assa Abloy

Assa Abloy VingCard Essence Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL420 Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood Pentagon 3P70 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale inTouch Technische Daten

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung