Assa Abloy Yale 7370 Series Bedienungsanleitung

7370 Series Multi-Point Lock

for Window Shutter Applications

Installation Instructions

Recommended Installation:

Install 7370 so that the

deadbolt is equidistant from

the top and bottom of the

shutter.

Attention Installer

Any retrofit or other field modification to a fire rated opening can

potentially impact the fire rating of the opening, and Yale Locks &

Hardware makes no representations or warranties concerning

what such impact may be in any specific situation. When

retrofitting any portion of an existing fire rated opening, or

specifying and installing a new fire-rated opening, please consult

with a code specialist or local code official (Authority Having

Jurisdiction) to ensure compliance with all applicable codes and

ratings.

An ASSA ABLOY Group brand

80-8470-7370-010 (10-12)

TABLE OF CONTENTS

Step 1 – Installation of Deadbolt Assembly

Step 2 – Installation of Bottom Bolt Assembly

Step 3 – Installation of Top Pusher Assembly

Step 4 – Aligning assemblies in preparation for drilling and pinning

Step 5 – Applying the Drill Jig for proper drilling

Step 6 – Pinning the Rods to engage the Deadbolt Lever

Step 7 – Installation of Inside and Outside Trim

Step 8 – Installation of Cylinder in Outside Trim (Optional)

Step 9 – Assemble the Top Latch to the Frame

Step 10 – Installation of Deadbolt Strike

Step 11 – Install the Bottom Strike

3 & 4

5 & 6

This device is intended to be part of an integrated window shutter, frame and hardware assembly

UL-approved for both FEMA 361 and ICC 500 guidelines for inswing window shutters. This

instruction sheet will take you through the following steps for full installation.

Installation Jig Components Drill Guide for Deadbolt Case

An ASSA ABLOY Group brand

80-8470-7370-010 (10-12)

Step 1 – Installation of the Deadbolt Assembly

Step 2 – Installation of the Bottom Bolt Assembly

• Place the window shutter on a horizontal surface

with the pin lever notch located at the top of the

shutter facing up.

• The recommended deadbolt assembly location

should be equidistant from the top and bottom

of the shutter.

• Assemble the deadbolt case into the lock pocket

provided in the door. Note the orientation of the

lock, the top of the deadbolt case indicates that

this should be toward the top of the shutter.

• Assemble the lock to the edge of the shutter

using (2) 1/4-20 x 1" Flat Head Cap Screws.

Lower Thru

Bolt Cutout

•

slide along the lower rod tubing but not slide on its

own when the rod is held vertically. Be sure that the

set screw is oriented so that it will be accessible

through the Lower Thru Bolt Cutout on the top side of

the shutter.

• When you insert the assembly into the shutter and

through the nylon guides of the deadbolt case this

lifting pad will be in a position to allow you to make the

final necessary adjustment. Note the orientation of the

bottom bolt assembly the double screw head side (not

shown in this image) should be facing the hinge side

of the shutter.

Continue on next page………….

Loosen the set screw so that the lifting platform will

Set Screw

An ASSA ABLOY Group brand

80-8470-7370-010 (10-12)

Step 2 – Installation of the Bottom Bolt Assembly continued

Nylon Guides •

Sub Assembly into the prep. hole in the bottom of the

shutter. As you guide the assembly up into the shutter

you will need to guide it into the bottom nylon guide of

the Deadbolt Assembly and then up thru the top nylon

guide.

• Seat the bottom bolt bracket against the shutters lower

reinforcement plate.

• Align Bottom Bolt Plate to shutter prep.

• Fasten the Bottom Bolt Assembly and Bottom Bolt

Plate to the bottom of the shutter using (2) #12-24 x 1"

Flat Head Cap Screws.

With the Deadbolt Retracted, slide the Bottom Bolt

Step 3 – Installation of the Top Pusher Assembly

•

shutter, making sure the plunger pin is oriented with

the clearance slot on the stop side of the shutter.

• Visually align the rod of the Top Pusher Assembly so

that it enters the tube of the Bottom Bolt Assembly

that extends out of the Deadbolt Assembly.

• Align the Top Strike plate to shutter prep. noting the

position of the beveled edge. It should be on the

same side as the plunger pin.

• Fasten the Top Strike plate and Top Pusher Assembly

to the top of the shutter using (2) #12-24 x 1" Flat

Head Cap Screws.

Slide this assembly into the prep. at the top of the

Strike Plate

Note beveled edge position

Plunger Pin

Top Pusher

Assembly

An ASSA ABLOY Group brand

80-8470-7370-010 (10-12)

Step 4 – Alignment of components in preparation for drilling and pinning

•

so that it extends the top latch to the proper

position for pinning. The Top Bolt Clamp will

assure that the top latch is in the correct

position for final installation.

• Prepare the lifting platform installation jig by

removing the two wing fasteners and their

washers.

• Introduce the lifting platform jig up through the

under side of the shutter as shown.

• Using the two wing fasteners and their

washers, secure the lifting platform jig to the

shutter.

The lifting platform jig will now be in position to

allow sliding the lifting platform (shown in step 2)

so that it rests against the shelf of the jig.

Continued on next page………….

Thread the Top Clamp into the threaded hole

An ASSA ABLOY Group brand

80-8470-7370-010 (10-12)

Step 4 – Alignment of components in preparation for drilling and pinning

Before continuing to the next step be certain the

top pusher and bottom bolt are in the correct

position.

• Bottom Bolt should be flush to the bottom of

the shutter.

• The lifting platform (item 1) should be moved

down the bottom rod and placed against the

shelf of the lifting platform jig.

• Next secure the platforms position by

tightening the cone point set screw (item 2).

This will assure the point on the set screw

embeds itself firmly into the bottom rod.

An ASSA ABLOY Group brand

80-8470-7370-010 (10-12)

Step 5 – Applying the drill jig for proper drilling

• Manually project the deadbolt by applying force

to the deadbolt lever toward the bottom of the

shutter.

• The deadbolt lever is now in a position to allow

the Drill Guide to be positioned above the

deadbolt and fixed into position using the two

drill guide positioning holes provided in both

sides of the deadbolt case.

• The Drill Guide is an alligator type jig. Loosen

the Drill Guide clamping screw, allowing the

jaws to rotate 90 degrees to allow the guide to

be positioned above the deadbolt and closed

around the shutter so that the pins on both

sides of the Drill Guide engage the two Drill

Guide Positioning Holes.

• Once the Drill Guide is engaged in the

positioning holes, tighten the Drill Guides

clamping screw so that it will firmly secure the

jig around the shutter.

• Using the Drill Guide Hole, drill a 1/8" hole (drill

provided with jig components) thru both sets of

rods.

Drill Guide

Positioning

Holes

Deadbolt

Lever

Drill Guide

Hole

Drill Guide

Positioning Pins

Drill Guide

Clamping Screw

An ASSA ABLOY Group brand

80-8470-7370-010 (10-12)

Step 6 – Pinning the Rods to engage the Deadbolt Lever

Step 7 – Installation of Inside and Outside Trim

Hole shown in proper pinning position.

Drive Pin

• Loosen the Drill Guide clamping screw allowing

the Drill Guide to be removed from the shutter.

• Manually retract the deadbolt by applying force

to the deadbolt lever toward the top of the

shutter.

• This will put the pinning hole in the proper

position for fastening the Drive Pin.

• Insert the Drive Pin from the underside of the

shutter and through the holes in the rods and

fasten the Drive Pin in place with the spring

washer.

• Install the outside trim by inserting it from

underneath the shutter (outside face).

• As it enters the shutter cavity the lifting pad in

the escutcheon will rest on the underside of the

lifting pad secured to the rods in step 4.

• Press the outside escutcheon against the

shutter surface.

• Install the inside trim by placing it over the

shutter prep and positioning the lifting pad of

the inside trim on the underside of the lifting

pad.

• Visually align the mounting holes of the inside

escutcheon to the mounting posts from the

outside escutcheon.

• Insert 4 mounting screws #12 -24 x 1-1/2" and

tighten screws.

The Lifting Platform Jig and the Top Clamp can now be removed from the shutter.

An ASSA ABLOY Group brand

80-8470-7370-010 (10-12)

Step 8 – Installation of Cylinder in Outside Trim (Optional)

Cylinder

Cylinder Collar

Cylinder Retaining Nut

Backplate

Outside Trim

Assembly

Step 9 – Assemble the Top Latch to the Frame

• Assembly the top latch into the top of the frame

using (4) 1/4"-20 x 1" Flat Head Cap Screws.

The angled surface should face the shutter.

• Insert the Cylinder into the Cylinder Collar

• Place the Cylinder Retaining Nut against the

backplate of the outside trim assembly,

• Feed the cylinder and cylinder collar into the

cylinder hole of the escutcheon and screw the

cylinder retaining nut to the cylinder until it is

fully seated with the cam straight up as shown.

• Secure the cylinder to the escutcheon by

tightening the cylinder retaining nut.

An ASSA ABLOY Group brand

80-8470-7370-010 (10-12)

Step 10 – Installation of Deadbolt Strike

Step 11 – Install the Bottom Strike

• Assemble the Deadbolt Strike to the frame

using (2) 1/4"-20 x 1" Flat Head Cap Screws.

Deadbolt Strike

• Place the Bottom Strike into the Strike Shim

and fasten to the frame using (2) 1/4"-20

Screws.

Install the Shutter into the frame assembly and shim for proper shutter gap and for the

shutter being square and plumb.

Bottom Strike

Strike Shim

Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their

respective owners and are mentioned for reference purposes only. These materials are protected under U.S. copyright laws. All contents current at time of publication.

Yale Security Inc. reserves the right to change availability of any item in this catalog, its design, construction, and/or its materials.

Product Support Tel 800. • www.yalelocks.com438.1951

Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.

An ASSA ABLOY Group brand

80-8470-7370-010 (10-12)

Inhaltsverzeichnis

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy effeff EX118R Bedienungsanleitung

Assa Abloy

Assa Abloy EL490 Bedienungsanleitung

Assa Abloy

Assa Abloy IKON eCLIQ N110 Bedienungsanleitung

Assa Abloy

Assa Abloy 8037...UL-91E91 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 809M Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL428 Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem 309N Installationsanleitung

Assa Abloy

Assa Abloy sFlipLock check 14471 Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem N7 Series Installationsanleitung

Assa Abloy

Assa Abloy Yale Smart Latch Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT FM7300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDM7220 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin IN220 PoE Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent ELR Series Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL590 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 ML20600 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDD424A Bedienungsanleitung

Assa Abloy

Assa Abloy 118F A71 Series Bedienungsanleitung

Assa Abloy

Assa Abloy ML20900 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron SAM Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1655 Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron GL1 Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL420 Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron Magnalock Series Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung