Assa Abloy Securitron GL1 Bedienungsanleitung
1
500-22090, Rev A
GL-1 Gate Lock
Installation Instructions and
Operating Manual
2
500-22090, Rev A
Table of Contents
Table of Contents..............................................................................................2
Specifications.....................................................................................................3
Physical..........................................................................................................3
Electrical.........................................................................................................3
Product Overview..............................................................................................3
Product Features:.....................................................................................3
Product Components........................................................................................4
Recommended Tools........................................................................................4
Installing the GL1 Electromechanical Gate Lock..........................................5
Perform a Pre-Installation Survey..............................................................5
Perform the Cylinder Lock/Cover Hole Plug Installation.........................8
Mount the GL1 and Connect the Electrical.............................................10
Complete the GL1 Installation...................................................................13
Operating Instructions....................................................................................13
Troubleshooting...............................................................................................14
MagnaCare®Lifetime Replacement Warranty............................................15
3
500-22090, Rev A
Specifications
Physical
Holding Force 2,000 lbs [907 kg]
Preload Up to 100 lbs (Fail Locked only)
Dimensions 2 ¾” L X 7 ¼” H X 3 ¼” D
[70 mm L X 184 mm H X 83 mm D]
Electrical
12 VDC Current Requirement Initial (Peak): 870 mA (~ 1 sec)
Reduced: 290 mA
Power Consumption: 3.5 Watts
24 VDC Current Requirement Initial (Peak): 720 mA (~ 1 sec)
Reduced: 170 mA
Power Consumption: 4.1 Watts
Operating Temperature –58 to +167 °F [–50 to +75 °C]
Product Overview
The GL1 Electromechanical Gate Lock is designed to secure a wide
variety of vehicle and pedestrian gate applications where security and
weather resistance are required. The GL1 functions equally well in both
electrically and manually operated gate installations and can be used for
swing gates, sliding gates, stock cage gates or other applications.
Product Features:
•2000 lbs holding force
•Operates under preload up to 100 lbs.
•Automatic dual voltage—no field adjustment required
•Manual key override (right or left hand)—Fail Locked only
4
500-22090, Rev A
•Self-aligning receiver (up to +/- 1/2" horizontally or vertically)
helps compensate for gate misalignment and sag
•Tamper proof cast housing
•Latch status monitor switch (SPDT)
•½”-14 NPSM inside pipe thread
•Surface Mount
•Black finish
Product Components
Upon unpacking this product, an inventory should be made to
ensure that all the required components and hardware have been
included. Along with these instructions and the installation
template, the lock assembly should include the following items:
Recommended Tools
Hammer Screwdriver, #2 Phillips
Center Punch Hex (Allen) wrench, 3/16” [5 mm]
Drill Bits: 5/16”, 3/8”, ½” Tap, ¼”-20 UNC [M6-1.0]
5
500-22090, Rev A
Installing the GL1 Electromechanical
Gate Lock
Installation Concerns
CAUTION: It is vital that all welding be completed prior to
making any electrical connections to the mounted
GL1. Welding in or around an electrically-connected
lock assembly can cause damage to the electronic
components.
•Installation should be performed by a qualified service person, who
conforms to all local codes and complies with The National Electrical
Code (or equivalent).
•The FMK-SL (Sliding Gate) and the FMK-SW (Swing Gate) mounting
bracket kits are recommended for installing the GL1.
•The GL1 must be mounted in the upright vertical position with the
conduit opening on the bottom.
•The GL1 should not be used for dual swing gates.
Perform a Pre-Installation Survey
Due to the variety of mounting configurations available with this product,
it is strongly recommended that an initial physical survey and
assessment be made of the actual area where the lock will be installed to
determine the optimal method of mounting prior to installation. The
following should be considered:
•Physical strength of mounting areas: It is recommended that the
structural integrity of mounting surfaces be strong enough to meet or
exceed the holding force of the lock.
•Protection of the lock from external attack: The lock and the wiring
must be protected to a reasonable degree from potential damage
due to intruders or vandals.
•Convenience and accessibility of area to be protected: The lock
6
500-22090, Rev A
assembly should be installed in a location that will not hinder or
create a potential safety hazard to authorized personnel routinely
accessing the protected area.
Because of the diversity in gate construction and installation
configurations, optimum mounting platforms may be achieved by welding
adequate size metal plates, channels or tubing to the fence frame and
the gate. Formed angle and brackets along with appropriately sized
fasteners may also be utilized to mechanically secure mounting
platforms for the lock and strike.
Figure 1, “Swinging Gate Mount,” Figure 2, “Sliding Gate Mount,” Figure
3, “Installation Spacing Dimensions,” and Figure 4, “Chassis Welding,”
show some basic mounting configurations on a chain-link style fence
frame and gate.
Figure 1. Swinging Gate Mount Figure 2. Sliding Gate Mount
7
500-22090, Rev A
Figure 3. Installation Spacing Dimensions
Figure 4. Chassis Welding
8
500-22090, Rev A
Perform the Cylinder Lock/Cover Hole Plug
Installation
NOTE 1: The GL1 provides for the additional function of an optional key-
operated cylinder lock. The cylinder lock can be installed to
either side of the lock cover, because the GL-1 lock latching
mechanism features an actuator lever that will engage the
cylinder lock from either side.
NOTE 2: IF the cylinder lock is not used, THEN a cover hole plug
(provided) must be installed on both sides of the cover.
1. SELECT the side of the lock cover that will be the most convenient
for the key access after installation if installing the optional manual
override.
2. INSTALL the optional cylinder lock.
NOTE: The following step is critical to the proper operation of the
mechanical override. The cam of the cylinder (“MS” type)
must come into contact with the actuator lever pin to
operate the release trigger of the lock mechanism when
the cover is assembled to the lock chassis.
a. ASSEMBLE the cam, as necessary, so that the key rotation
moves the cam to point toward the rear (opening) of the cover.
b. INSERT the cylinder lock with applicable spacer (i.e., Sargent
Number 90) into the applicable cover hole (see table below and
Figure 5, “Cylinder Lock Installation”).
Size of Cylinder Lock Spacer Required
1” ¼”
1 1/8” 3/8”
9
500-22090, Rev A
Figure 5. Cylinder Lock Installation
c. SLIP the spacer over the cylinder lock and INSERT the cylinder
lock into the applicable side hole on the lock cover.
d. SLIP the lock mounting nut over the cylinder lock inside the
cover and THREAD the nut onto the lock body by hand.
e. TIGHTEN to secure the nut in place using the provided cylinder
nut tool.
f. INSTALL a cover hole plug in the opposite side of the cover, and
SECURE its retaining nut using the provided retaining nut tool.
NOTE: The following steps are performed if the cylinder lock is not
used.
3. INSTALL the two cover hole plugs (provided) through both sides of
the cover (see Figure 6, Cover Hole Plug and Retaining Nut”).
4. SECURE the cover hole plugs in place using the retaining nuts and
provided cylinder nut tool (see Figure 6, “Cover Hole Plug and
Retaining Nut”).
10
500-22090, Rev A
Figure 6. Cover Hole Plug and Retaining Nut
Mount the GL1 and Connect the Electrical
NOTE: The FMK-SL (Sliding Gate) and the FMK-SW (Swing Gate)
mounting bracket kits are recommended for installing the GL1.
1. IF not using one of the recommended mounting bracket kits,
THEN USE the included template to locate and install mounting
hardware.
2. INSTALL the lock chassis using the top two lock chassis mounting
positions.
NOTE: The following chart shows wire gauge sizing versus voltage
versus distance:
Distance Gauge 12V Gauge 24V Distance Gauge 12V Gauge 24V
100 FT 20 GA 22 GA 800 FT 12 GA 14 GA
200 FT 18 GA 20 GA 1500 FT 10 GA 10 GA
400 FT 14 GA 16 GA 2000 FT 8 GA 8 GA
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Assa Abloy Sperren Handbücher
Assa Abloy
Assa Abloy Sargent KP Series Installationshandbuch
Assa Abloy
Assa Abloy SARGENT Profile LK Series Installationshandbuch
Assa Abloy
Assa Abloy Yale 7370 Series Bedienungsanleitung
Assa Abloy
Assa Abloy MAUER 101.132. Bedienungsanleitung
Assa Abloy
Assa Abloy Abloy EL590 Bedienungsanleitung
Assa Abloy
Assa Abloy 8800 Series Bedienungsanleitung
Assa Abloy
Assa Abloy ASSA Coded 1.2 Installationshandbuch
Assa Abloy
Assa Abloy Securitron M680EBD Bedienungsanleitung
Assa Abloy
Assa Abloy SARGENT FM7300 Series Bedienungsanleitung
Assa Abloy
Assa Abloy Yale nexTouch NTM 610 Montageanleitung
Assa Abloy
Assa Abloy 836S Bedienungsanleitung
Assa Abloy
Assa Abloy Aperio KS100 Bedienungsanleitung
Assa Abloy
Assa Abloy Securitron M38 Series Bedienungsanleitung
Assa Abloy
Assa Abloy Corbin Russwin FE6700 Series Bedienungsanleitung
Assa Abloy
Assa Abloy Securitron SAM Bedienungsanleitung
Assa Abloy
Assa Abloy 841C Bedienungsanleitung
Assa Abloy
Assa Abloy OneSystem 309N Installationsanleitung
Assa Abloy
Assa Abloy Corbin Russwin UT5200 Series Kurzanleitung
Assa Abloy
Assa Abloy Lockwood 3579 Series Bedienungsanleitung
Assa Abloy
Assa Abloy HES Aperio K100 Handbuch
