AT&T SPIRIT SPIRIT Attendant Bedienungsanleitung

AT&T

SPlRIT®

Communications System

SPIRIT Attendant ConnecT/R

Owner’s Manual

IMPORTANT SAFETY INSTRUCTIONS

To reduce risk of injury from fire or electric

shock, always follow bask safety precautions

when using this product.

The safety symbol (exclamation point

inside a triangle) on the Attendant

ConnecT/R alerts you to the Important operat-

ing and maintenance instructions below.

Read and understand all instructions in this

Owner's Manual.

Observe all warnings and instructions

marked on the product.

Unplug this product from wall outlets and

telephone jacks before cleaning. Clean

exposed parts with a soft, damp cloth. Do

not use liquid or aerosol cleaners, and never

immerse in water.

Do not use the product near water or when

you are wet. For example, do not use it in a

wet basement or near a swimming pool,

bathtub, shower, sink, or laundry tub. If the

product comes in contact with any liquids,

unplug the power and line cords immedi-

ately. Do not plug the product back in until

it has been dried thoroughly.

Install this product securely on a stable

surface. Damage may result if the product

falls.

Install this product in a protected location

where no one can step on or trip over power

and line cords. Do not place objects on the

cords that may cause damage or abrasion.

Do not allow anything to rest on the power

cord. Do not locate this product where the

cord will be abused by persons walking on

it. Do not overload wall outlets, as this can

result in the risk of fire or electric shock.

Never push objects of any kind into this

product through housing openings because

they may touch dangerous voltage points or

short out parts, resulting in possible fire or

electric shock.

If this product does not operate normally,

see the Troubleshooting section of this

manual. If you cannot resolve the problem,

or if the product is damaged, Call the AT&T

Helpline at 1-800-628-2888. Do not open the

product. Opening the product may expose

you to dangerous voltages or other risks.

10. During thunderstorms, avoid using tele-

phones except cordless models. There may

be a slight chance of electric shock from

lightning.

11. Do not use a telephone in the vicinity of a

gas leak. If you suspect a gas leak, report it

immediately, but use a telephone away from

the area where gas is leaking.

12. This product should be operated only from

the type of power source indicated on the

power transformer (see Item 13, below). lf

you are not sure of the type of power supply

to your business or home, consult your local

power company.

13. Use only a UL Listed wall plug-in power

transformer that has Class 2 outputs and

the following characteristics:

Input rating: 99-127 V AC rms 60 Hz

150 mA maximum

Output rating:

27-35 V DC at 200 mA

14-18 V DC at 200 mA

The power transformer supplied with the

product has these characteristics.

SAVE THESE INSTRUCTIONS

Table of Contents

Introduction

Installation

Step 1— Mount the SPIRIT® Attendant ConnecT/R

Step 2—Connect the SPIRIT Attendant ConnecT/R

Step 3—Test the Equipment

Troubleshooting

Appendix A—Wiring Requirements

Appendix B—Warranty

While reasonable efforts were made to ensure that the information in this document was complete and

accurate at the time of printing, AT&T assumes no responsibility for any errors. Changes or corrections to

the information contained in this document maybe incorporated into future re-issues.

Document No. 518-453-712 Comcode 106455868

Issue 1

January 1991

Printed in USA.

Introduction

The following descriptions define important

terms used in this manual.

● The SPIRIT Attendant is a device which

provides automated call-handling capabili-

ties for the SPIRIT Communications System.

The SPIRIT® Communications System

Attendant ConnecT/R provides you with This Owner’s Manual will help you set up your

the ability to add a SPIRIT Attendant to

SPIRIT

Attendant ConnecT/

R for your particu-

your SPIRIT System. It connects to the lar business needs.

controller.

The controller is the central processor

through which all SPIRIT calls in your

company are processed.

Figure 1. SPIRIT Attendant ConnecT/R

●

SPIRIT

is a registered trademark of AT&T.

Figure 2. SPIRIT Attendant ConnectT/R Applications

Installation

INSTALLATION INSTRUCTIONS 3. Never touch uninsulated telephone wires or

terminals unless the telephone line has been

Never install telephone wiring during a disconnected at the network interface.

Iightning storm. 4. Use caution when installing or modifying

Never install telephone jacks in wet loca- telephone lines.

tions unless the jack is specifically designed

for wet locations.

Directly connected by a cord from one unit to the

other, or connected via a wiring run.

Figure 3.

SPIRIT

Attendant ConnecT/R with Attached

SPIRIT

Attendant

NOTE: The switches on the SPIRIT Attendant ConnecT/R are not used. They have

been removed to prevent accidental incorrect installations.

4Step 1 — Mount the SPIRIT Attendant

ConnecT/R (optional).

The SPIRIT Attendant ConnecT/R is designed

to be placed on your desk or mounted on any

vertical surface.

Do not place it on the floor.

Hardware has been included to mount the

SPIRIT Attendant ConnecT/R on the wall: two

plastic wall-mount tabs, two anchors, and two

#6 screws.

of the tab against the inside of one of the

feet. Repeat for the second tab.

Select an appropriate location. The SPIRIT

Attendant ConnecT/R can be no more than

six feet from its power supply (an AC outlet

that isn’t controlled by a wall switch) and no

more than six feet from the devices attached

to it. The bottom of the SPIRIT Attendant

ConnecT/R should be at least two feet from

the floor.

Position the SPIRIT Attendant ConnecT/R

so the side with the jacks and settings is

down or to the side, but not up.

Remove the backing from the plastic tabs.

Gently position a tab by aligning the end of

the adhesive with the outside edge of the

SPIRIT Attendant ConnecT/R and the side

Press the tabs firmly into position.

With the tabs at the top, hold the SPIRIT

Attendant ConnecT/R against the wall

where you plan to mount it and use a pencil

to mark the location of the holes in the tabs.

The bottom of the SPIRIT Attendant

ConnecT/R should be at least two feet from

the floor.

If you have plywood walls or walls with a

sturdy supporting structure (either wood

studs or cross members), partially screw the

two screws into the wall at the marks,

remove them, hang the tabs on the screws,

and then tighten the screws.

For plaster, plasterboard, cinder block, or

brick surfaces, drill a 3/16" hole at each

mark and insert an anchor into each of the

holes. Gently tap each anchor with a ham-

mer until it is flush with the surface. Screw

the screws partially into the anchors, remove

them, hang the tabs on the screws, and then

tighten the screws.

Step 2 — Connect the SPIRIT Attendant

ConnecT/R to the controller and the SPIRIT

Attendant to the SPIRIT Attendant

ConnecT/R.

Please check the cabling requirements in Appen-

dix A before proceeding. Consult with the

person who customized your SPIRIT System

before attaching the SPIRIT Attendant

ConnecT/R to the controller.

NOTE: The "4-wire cord" mentioned in the

steps below comes with the SPIRIT Atten-

dant ConnecT/R. Any cord you may have

that is connecting a SPIRIT Telehone to

the controller is also 4-wire cord .

1. Connect the SPIRIT Attendant ConnecT/R

to the Controller. Using 4-wire cord, plug

one end into the CTRLR jack on the back of

the SPIRIT Attendant ConnecT/R and

connect the other end into the STATION jack

on the controller.

2. Connect the SPIRIT Attendant to the

SPIRIT Attendant ConnecT/R. Using the

line cord provided with the SPIRIT Atten-

dant, plug one end into the LINE jack (or its

equivalent) on the back of the SPIRIT

Attendant and connect the other end to the

TEL DEVICE jack on the SPIRIT Attendant

ConnecT/R.

3. Do not connect a SPIRIT Telephone to the

SPIRIT Attendant ConnecT/R.

4. Connect the SPIRIT Attendant ConnecT/R

to the AC power outlet. Plug the power

connector into the POWER jack on the back

of the SPIRIT Attendant ConnecT/R. To

prevent the power cord from pulling out

easily, make a small loop of cord near the

power connector and slip it behind the strain

relief tab next to the POWER jack on the

SPIRIT Attendant ConnecT/R. Plug the

wall transformer into an AC power outlet

that is at least 3 feet away from the controller

and not controlled by a wall switch. (If it is

any closer to the controller, you may hear a

hum on your SPIRIT System.)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AT&T Konferenzsystem Handbücher

AT&T

AT&T MERLIN 410 Bedienungsanleitung

AT&T

AT&T MERLIN PIus Attendant Montageanleitung

AT&T

AT&T MERLIN 410 Bedienungsanleitung

AT&T

AT&T MERLIN LEGEND Release 2.0 MLX Queued Call... Handbuch

AT&T

AT&T Merlin 1030 Bedienungsanleitung

AT&T

AT&T MERLIN Plus Benutzerhandbuch

AT&T

AT&T Merlin Legend BIS10 Bedienungsanleitung

AT&T

AT&T Spirit Communications System Bedienungsanleitung

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Technisches Handbuch

AT&T

AT&T Merlin 1030 Bedienungsanleitung

AT&T

AT&T StaR Adapter Handbuch

AT&T

AT&T PARTNER II Release 3.1 Bedienungsanleitung

AT&T

AT&T Merlin 3070 Bedienungsanleitung

AT&T

AT&T Lucent Technologies PARTNER Plus Kurzanleitung

AT&T

AT&T MERLIN LEGEND Calling Group Bedienungsanleitung

AT&T

AT&T MERLIN 410 Stücklistenhandbuch

AT&T

AT&T System 85 Installations- und Betriebshandbuch

AT&T

AT&T Merlin 3070 Bedienungsanleitung

AT&T

AT&T Merlin 1030 Bedienungsanleitung

AT&T

AT&T MERLIN 820 Bedienungsanleitung

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Bedienungsanleitung

AT&T

AT&T Merlin II Bedienungsanleitung

AT&T

AT&T MERLIN Attendant for MERLIN LEGEND Montageanleitung

AT&T

AT&T MERLIN LEGEND Service-Handbuch

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung