AT&T MERLIN 410 Bedienungsanleitung

AT&T

MERLIN

COMMUNICATIONS SYSTEM

INSTALLATION GUIDE:

MODELS 206 AND 410

Table of Contents

Page

Introduction

Getting Started

Installing the Control Unit

Position the Control Unit

Set the Control Unit Switches

Connect the Control Unit to the AC Outlet

Prepare the Network Interface

Test the Outside Lines

Connect the Control Unit to the Network Interface

Voice Terminal Wiring

Jack Field Connection

Direct Connection

Connecting the Voice Terminals

Prepare the Voice Terminals

Connect Each Voice Terminal to the System

Test Each Voice Terminal for Dial Tone

Attach and Verify the Intercom Numbers

Installing Accessories

Cartridges

Other Accessories

System Tests

Place an Outside Call

Place an Intercom Call

What’s Next?

System Changes

Adding an Outside Line

Adding a Voice Terminal

Moving a Voice Terminal

Changing Touch-Tone/Rotary Service

Upgrading from Model 206 to Model 410

Troubleshooting

Troubleshooting Table

General Test

Appendix A: Interference Information

Appendix B: FCC Registration and Repair Information

Index

Introduction

This installation guide tells you how to install and test your MERLIN® com-

munications system, Model 206 or 410. It leads you step by step through system

installation, from a pre-installation checklist to system tests. You should per-

form the steps in the order in which they are presented because many of the

earlier steps prepare the system for later steps.

When you complete the steps in this guide, see the administration manual that

came with your system for programming and administration instructions. Your

system may not be fully operable until you have programmed and administered it.

This guide includes the following sections:

●

Getting Started describes how to prepare for system installation.

Installing the Control Unit explains how to set up and connect the

system’s control unit.

Voice Terminal Wiring provides instructions for connecting the system

wiring.

Connecting the Voice Terminals

explains how to connect your voice ter-

minals

(MERLIN

system telephones) to your system.

Installing Accessories

suggests some accessories you may want to con-

sider adding to your system.

System Tests

provides tests to help you determine if you’ve installed your

system properly.

What’s Next?

refers you to documents that explain how to customize and

use your system to meet your particular business needs.

System Changes

explains how to rearrange or alter your system once it

is in place.

Troubleshooting isolates and identifies specific system problems that

could arise during installation, and suggests solutions to basic problems.

The steps in this guide are numbered in order of performance. To visualize a

step as it is described, refer to the drawings accompanying the text. The

numbers in the drawings correspond to the step numbers in the text. The con-

trol unit most often pictured in this guide is a Model 410, but the information

presented usually applies to the Model 206 control unit as well. When there

are exceptions, both control units are pictured.

Getting Started

This guide assumes the tasks on the following list have been completed. Review

the list carefully. If you have not completed the tasks on the list, do so now.

●Make sure the necessary wiring is in place.

You must have a network interface that links your

MERLIN

system to the

local telephone company’s lines. A telephone company representative

should have installed your outside lines and labeled the network interface

to indicate the telephone number for each outside line.

You must also have wiring that connects your voice terminal locations to

your control unit location. If your voice terminal locations are close enough

to your control unit to make direct connection practical, you may have

planned to connect your voice terminals directly to the control unit with

modular voice terminal cords and, if necessary, modular voice terminal

extension cords. If you are planning to connect your voice terminals directly

to the control unit, this guide tells you how to do so at the appropriate point

in the installation sequence.

If conditions at your business make direct connections between your voice

terminal locations and your control unit location impractical, then you have

connected the locations through the building wiring. You may have had

the necessary wiring professionally installed, or perhaps you did the wir-

ing yourself following the instructions in the Wiring Installation Kit. In either

case, you should now have building wiring that runs from the voice ter-

minal locations to the control unit location. The wiring runs should end in

modular wall jacks at the voice terminal locations and in a group of jacks

mounted in one or two jack panel boxes (the “jack field”) at the control

unit location. Inside the right door (the one with the handle) of each jack

panel box you should find a label indicating the wiring run number and

endpoint location (for example, “w1 Reception area”) for each jack in the

jack field.

The drawing, top right, shows a direct connection between a voice terminal

and the control unit. The drawing,bottom right,shows a voice terminal con-

nected to the control unit through the building wiring.

Control

unit

Voice terminal

Modular voice terminal cord

Control unit

Jack field

Voice terminal

Building

wiring

●

Check the items in your shipment against your copy of the order form. Become familiar with your MERLIN system.

Make sure the items and quantities agree. Save the instructions packed Review the figure of a simple MERLIN system configuration, opposite

with components; you may need to refer to them later. And keep the pack-

page, and note how components are related to one another.

ing boxes just in case you have to return components under warranty.

Get acquainted with the system environment.

Review the planning sheets you drew up when you ordered the system.

Confirm the voice terminal locations, and make sure the control unit loca-

tion meets the following environmental standards:

—Operating temperature: 40-104°F (4-40°C)

—Humidity: not to exceed 80%

—Ventilation: Leave 6 inches of space above and to the sides of the con-

trol unit to prevent overheating. Keep the control unit away from sources

of extreme heat (furnaces, heaters, attics, or direct sunlight). Do not

stack multiple control units in rooms that are not air-conditioned; in-

stall them side by side at least 6 inches apart.

—Airborne contamination:Do not expose the control unit to moisture, cor-

rosive gases, dust, chemicals, or similar substances.

If your control unit location does not meet these standards, your warranty may

become void.

The control unit and the cartridges it contains provide the power

and intelligence for all voice terminals and accessories.

Modular jumper cords connect the control unit to the jacks in the

jack field.

The jack field serves as an interface between the control unit and

the building wiring.

Building wiring ties the whole system together, connecting the

voice terminal locations to the control unit location.

Modular wall jacks connect the voice terminals to the building

wiring.

Modular voice terminal cords connect the voice terminals to the

modular wall jacks.

Voice terminals

provide telephone functions and access to the ad-

vanced features in the control unit.

The network interface jacks provide connections to the local

telephone company lines.

Line cords connect the control unit to the network interface.

The ac outlet is the electrical power source for the control unit.

NOTE:

Modular jumper cords are identical to modular voice terminal cords.

They have different names in this guide to reflect their different functions

and locations in the system.

To comply with FCC regulations, notify your local telephone company of

the following before permanently connecting your system to their lines:

System registration number: AS 593M-13529-KF-E

Ringer equivalence number: 0.8A

Telephone numbers of the lines to which you are connecting your

system.

—

AC outlet

Line cord

Network interface

Control unit

Modular jumper cord

Jack field

Voice terminal

Modular voice terminal cord

Modular wall jack

Building wiring

Installing the Control Unit

Installation procedures are basically the same for both Model 206 and Model

410. The instructions point out only those differences between the models that

affect installation.

POSITION THE CONTROL UNIT

If you plan to wall mount your control unit, follow the instructions in the booklet

titled CIB 3029 (for Model 206) or CIB 3030 (for Model 410) in your Control Unit

Installation Kit.

Whether you wall mount your control unit or place it on a table or shelf, make

sure it’s within 5 feet of an ac outlet that is not switch-controlled, within 5 feet

of the network interface, and within 6 inches of the jack field, if you have one.

The drawing, right, provides a diagram for positioning the control unit.

5 feet, maximum

6 inches, maximum

5 feet, maximum

NOTE:

The ac outlet should be a 117-volt, 60-Hz, 3-prong, third-wire ground-

ed outlet. Proper grounding protects the system against damage from power

surges caused by static discharge and lightning. You should have an electri-

cian check the outlet’s third wire to make sure the outlet is properly grounded.

Power consumption for both models is 40 watts during normal operation.

SET THE CONTROL UNIT SWITCHES

●

Find the Tone/Pulse switch near the top of the center panel on the front

of the control unit.

If you have rotary (pulse) telephone service, set the switch toPulse

(right).

If you have Touch-Tone signal telephone service, set the switch to

Tone (left).

Find the row of switches labeled Ringing on the left panel of the con-

trol unit. Set all of them to Yes (up) for now. You may want to reset these

switches later when you customize your system.

Tone/Pulse switch

Ringing switches

CONNECT THE CONTROL UNIT TO THE AC OUTLET

The outlet should not be switch-controlled. Plugging your control unit into a

switch-controlled outlet invites accidental disconnection of the system.

●

Find the power cord attached to the control unit and plug it into the ac

outlet.

The green power light on the control unit goes on.

The red warning light next to the power light comes on momentarily and

then goes off.

If the green power light does not come on, test the outlet by plug-

ging in a radio or lamp. If the outlet is working properly, your con-

trol unit may be faulty. Contact your equipment supplier for

assistance before proceeding with the installation.

If the red warning light doesn’t blink or remains lit, unplug the power

cord and then plug it in again. If the warning light still doesn’t

operate properly, contact your equipment supplier for assistance

before proceeding with the installation.

Unless otherwise instructed, leave the power cord plugged into the ac

outlet throughout the remaining installation procedures.

Warning light Power light

AC outlet

PREPARE THE NETWORK INTERFACE

Your local telephone company should have installed a network interface with

1-line jacks (RJ11-type) or 2-line jacks (RJ14-type) for connecting your

MERLIN

system to your outside telephone lines. The drawing, right, shows the two types

of network interface and the 2-line adapter (267C) for the 2-line network inter-

face jack. The table, below, tells you what to do depending on the type of net-

work interface you have.

If the Network Interface

And

Do This

has a 1-line jack

(RJ11-type) for each out-

side line

each jack is labeled with

its telephone number Go on to the next sec-

tion, “Test the Outside

Lines,” page 9.

1-Line jack (RJ11-type)

each jack is not labeled

with its telephone

number

Label each jack with

its telephone number

from the list provided

by the local tele-

phone company.

Go on to the next sec-

tion, “Test the Out-

sides Lines,” page 9.

has 2-line jacks

(RJ14-type) for the out-

side lines

each jack is labeled with

the telephone numbers

for its two outside lines

Plug a 2-line adapter

(267C) into each jack.

Go on to the next sec-

tion, “Test the Out-

side Lines,” page 9.

each jack is not labeled

with the telephone

numbers for its two out-

side lines

Label each jack with

the two telephone

numbers for its out-

side lines from the list

provided by the local

telephone company.

2-Line jack

(RJ14-type)

Plug a 2-line adapter

(267C) into each jack.

Go on to the next sec-

tion, “Test the Out-

side Lines,” page 9.

2-Line adapter

(267C)

TEST THE OUTSIDE LINES

This step is optional, but if you have a basic Touch-Tone or rotary telephone with

a modular plug, you should test your outside line connections now. It can save

time and frustration later.

NOTE: A MERLIN system voice terminal will not work for this test.

Network interface

Take a basic Touch-Tone or rotary telephone with a modular plug to the

network interface.

Plug the telephone’s modular line cord into each outside line jack, and

listen for a dial tone.

AndDo This

you have tested each

each outside line has a Continue with the

outside line

dial tone installation.

a line does not have a

the jack for that line at Have the local tele-

dial tone

the network interface is phone company check

a 1-line jack (RJ11-type)

the line and the network

interface. Meanwhile,

continue with the

installation.

the jack for that line at Replace the adapter

the network interface is with another one and try

a 2-line jack (RJ14-type)

again for a dial tone. If

with a 2-line adapter the problem remains,

have the local telephone

company check the line

and the network inter-

face. Meanwhile, con-

tinue with the

installation.

Andere Handbücher für MERLIN 410

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AT&T Konferenzsystem Handbücher

AT&T

AT&T Merlin 3070 Produkthandbuch

AT&T

AT&T SPIRIT 308 Benutzerhandbuch

AT&T

AT&T Merlin 1030 Bedienungsanleitung

AT&T

AT&T Merlin 3070 Bedienungsanleitung

AT&T

AT&T MERLIN 410 Stücklistenhandbuch

AT&T

AT&T Spirit Communications System Bedienungsanleitung

AT&T

AT&T MERLIN Plus Installationsanleitung

AT&T

AT&T SPIRIT 2448 Expansion Unit Bedienungsanleitung

AT&T

AT&T Merlin 3070 Bedienungsanleitung

AT&T

AT&T Merlin 1030 Bedienungsanleitung

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Direct-Line... Handbuch

AT&T

AT&T MERLIN Attendant for MERLIN LEGEND Montageanleitung

AT&T

AT&T System 85 Installations- und Betriebshandbuch

AT&T

AT&T Merlin II Bedienungsanleitung

AT&T

AT&T Merlin Legend BIS10 Bedienungsanleitung

AT&T

AT&T Merlin II Benutzerhandbuch

AT&T

AT&T Merlin Legend BIS22D Bedienungsanleitung

AT&T

AT&T Merlin 1030 Bedienungsanleitung

AT&T

AT&T SPIRIT 308 Bedienungsanleitung

AT&T

AT&T Merlin 3070 Bedienungsanleitung

AT&T

AT&T MERLIN Plus Benutzerhandbuch

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Bedienungsanleitung

AT&T

AT&T Partner II Betriebsanleitung

AT&T

AT&T MERLIN LEGEND Release 2.0 Analog Multiline... Betriebsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung