AT&T 135 Bedienungsanleitung

Design Line

Telephone 135

User’s Manual

Part 2

Printed in Mexico. 848234050 Issue 1AT&T

AT&T 135 Quark pdf 7/22/98 11:26 AM Page 1

PARTS CHECKLIST

Remember to save your sales receipt in case you ever need

warranty service, and make sure this telephone package

includes the items shown below:

7-foot line cord 5-inch line cord

Coiled

handset cord

Telephone

Base

Handset

Ringer

Volume Dial Mode

Switch

AT&T 135 Quark pdf 7/22/98 11:26 AM Page 2

INSTALLATION

Dial Mode Switch Selection

Set theDial Mode switch on the side of the set to TONE

(touch tone) or PULSE (dial pulse/rotary) telephone service.

Make sure you choose the correct dialing method; touch

tone dialing will not workif you have dial pulse service.

The temporary tone dialing is activated by pressing

while in pulse mode.

Table

1. Remove the base by sliding it sideways as indicated by

the “REMOVE” arrow.

2. Connect long line cord to telephone.

Plug the line cord into the LINE jack on the bottom of

the phone.

3. Reinstall the base with the wide edge at the back of

the telephone.

Insert the base tabs into the slots on the bottom of the

telephone and feed the line cord through the hole in the

wide end of the base. Turn the telephone right-side up; it

should sit flat on your table during use.

4. Set the Dial Mode switch.

The Dial Mode switch is on the side of the phone. Use a

ball point pen to set the switch to TONE if you have tone

telephone service, or to PULSE if you have dial pulse

(rotary) telephone service.

5. Connect line cord to modular wall jack.

Plug the free end of the line cord into a modular wall

jack. Make sure it snaps firmly in place.

6. Connect handset to telephone.

Plug the coiled end into the handset jack on the side of

the phone. Plug the other end of the coiled cord into the

handset, then hang up.

Wall

1. Remove the base.

AT&T 135 Quark pdf 7/22/98 11:26 AM Page 3

INSTALLATION (continued)

2. Connect short line cord to telephone.

Plug the 5-inch line cord into the LINE jack on the bot-

tom of the phone.

3. Reinstall the base.

Turn the base so that the larger end is toward the bottom

of the telephone. Reinstall the base by inserting the top

tabsinto thephone slots. Then slide sideways in the

direction of the “INSTALL” arrow to lock into the phone.

4. Reverse the handset tab.

To mount the telephone on a wall, you must reverse the

handset tab. This tab holds the handset when you hang

up. Hold down the switchhook, and slide the tab up and

out of its slot (Figure 1). Turn the tab so that the end with

the “hook” is up (Figure 2). Then insert the tab back into

its slot (Figure 3).

5. Connect the line cord to the modular jack and mount

the phone onto the wall jack.

Plug the free end of the line cord into a modular wall

jack. Make sure the cord snaps firmly into place. Place

the phone on the wall jack mounting studs and pull down

until it is held securely (Figure 4).

Figure 1 Figure 2 Figure 3

Figure 4

AT&T 135 Quark pdf 7/22/98 11:26 AM Page 4

Redial

The telephone always stores in memory the last number

dialed. To dial the same number again, press .

The redial memory can accept numbers up to 24 digits long.

The number will remain in memory untilyou change it by

dialing another telephone number.

For privacy, you can erase the redial memory. Lift the hand-

set, then press any digit (1-9).

Flash

Press instead of pressing the switchhook to activate

customer calling services such as call waiting or three-way

calling. You may have to press other buttons before or after

as explained in custom calling instructions provided

by your local telephone company.

Ringer Volume

The RINGER volume switch allows you to adjust the

loudness of the telephone ringer from OFF to HI. Slide the

switch to the desired volume level.

Volume Buttons

The VOLUME button adjusts the handset during your call.

While on a call, press to increase volume, to

decrease volume.

(Turn over for more Operation,

Memory and In Case of Difficulty)

OPERATION

Dial Mode

This telephone has a selectable push-button dial and will

work with either tone or rotary telephone service. It can

be set to work directly with long distance or certain other

services that require tone signaling including some tone

activated computer systems.

AT&T 135 Quark pdf 7/22/98 11:26 AM Page 5

MEMORY

Memory Features

Numbers will remain stored in memory unless you erase or

change them by entering other numbers.

Capacity: This telephone can store up to 9 different phone

numbers, each up to 24 digits long.

Speed Dialing: Nine telephone numbers can be stored in

standard speed-dialing locations. You can dial any of these

numbers by pressing two buttons.

Temporary Tone Dialing

Temporary tone dialing is used

only when you have rotary

service. It allowsyou access

to services that require tone

signaling, including some tone-

activated computer systems

(e.g., telephone banking).

To change from pulse (rotary)

to tone dialing during a call:

1. Dial a telephone number with the dial mode switch set to

PULSE.

2. Press ; all buttons pressed after this will send

tone signals.

3. After you hang up, the phone automatically returns to

rotary service.

OPERATION (continued)

NOTE: You may choose to store emergency numbers

in memory locations. This feature is provided only as a

convenience and the manufacturer assumes no responsi-

bility for customer reliance upon the memory feature.

AT&T 135 Quark pdf 7/22/98 11:26 AM Page 6

MEMORY (continued)

Directory Card: Remove the directory card. Write your

telephone number in the space provided. Also write the tele-

phone numbers (or names) that you want to store in each

memory location. Reinstall the card and clear plastic cover.

Speed Dialing

To program numbers into memory:

1. Press .

2. Enter telephone number. You will hear a click when

each button is pressed.

3. Press .

4. Enter a digit (1-9) for the memory location where the

number is to be stored.

5. Hang up after the number is entered correctly.

Repeat steps 1-5 to store another number.

To dial:

1. Listen for dial tone.

2. Press .

3. Press memory location (1-9).

Memory Erase

To erase any number from memory, you can enter another

number in the same location.

NOTE: Numbers programmed into a memory location

might not be retained if the telephone has been

unplugged from the line jack for a half hour or more.

AT&T 135 Quark pdf 7/22/98 11:26 AM Page 7

IN CASE OF DIFFICULTY

If this telephone does not work properly, try the following

suggestions before seeking repair assistance.

No Dial Tone

☞Make sure all plugs are connected properly. Inspect the

line cord connections at the modular jack and at the tele-

phone. Also inspect the coiled handset cord connections

at both ends.

☞Unplug the telephone and connect it to another modular

jack. If it still does not work, try another telephone; if

neither telephone works, the problem is not in this tele-

phone. The trouble may be caused by local telephone

company lines, central office equipment, or the wiring in

your home.

Calls Cannot Be Dialed, or Are Dialed Slowly

Reset Dial Mode switch. If you have rotary service, you

cannot dial numbers with the switch set to TONE. Set the

switch to PULSE, then hang up and dial again.

If you have tone dialing service, you can use either tone or

dial-pulse mode. If you set the switch to TONE, numbers

are dialed much more quickly.

Telephone Does Not Ring

☞Make sure the Ringer switch is not set to OFF.

☞If there are several other phones on the same line, try

disconnecting some of the other telephones. Having too

many telephones can also create problems such as low

ringer volume or impaired quality during calls.

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung

Axess Telecom

Axess Telecom ACW-1xP800 Bedienungsanleitung