AT&T TRIMLINE 210 Bedienungsanleitung

USER’S MANUAL

Part 2

AT&T and the globe symbol are registered trademarks of AT&T Corp.

licensed to Advanced American Telephones.

Printed in China. 850005208 Issue 2AT&T 12/00

TRIMLINE®

Memory

Telephone 210

Please also read Part 1 —

Important Product Information.

TABLE/DESK INSTALLATION

This telephone includes a 7-foot line cord with a

modular plug on each end. Use this cord to connect

the telephone to a modular jack.

1Fill in directory card

Remove the directory card and

write in your own telephone

number. Also write the

telephone numbers (or names)

that you want to store in each

memory location.

Reinstall the card and clear

plastic cover.

2Connect line cord to telephone

Plug the long line cord into the

jack on the underside of the

telephone base. Then feed the

line cord through the channel

provided so the telephone sits

flat on your table or desk

during use (Figure 1).

3 Connect line cord to wall jack

Plug free end of the line cord

into a modular jack. Make sure

it snaps firmly into place.

4 Set DIAL mode switch

This product comes set in the

tone (TT) mode. Make sure

you choose the correct dialing method

(TT or DP); touch tone dialing will not

work if you have dial pulse service.

5 Connect handset to base

Plug one end of the coiled handset cord into the

handset, and the other end into the base. Then

hang up.

6 Check for dial tone

Lift the handset and listen for dial tone. If you

cannot hear a dial tone, refer to “In Case of

Difficulty” and try to correct the problem.

TO DISCONNECT the telephone, squeeze the

clip on the modular plug and pull it out of the jack.

Figure 1

Figure 2

WALL INSTALLATION

1Fill in directory card

Remove the directory card and write in your own

telephone number. Also write the telephone

numbers (or names) that you want to store in

each memory location.

2 Reverse handset tab

To install the telephone on a wall jack, you must

reverse the small tab beneath the directory card. This

tab holds the handset in place when you hang up.

Remove the directory card and plastic cover. Use

a paper clip to lift and remove the handset tab.

Reverse the tab and reinstall it as shown (Figure 1).

Then replace the directory card and cover.

3Plug the line cord into the

jack on the underside of the

base. Feed the line cord into the

channel and wind it around the

mounting area. Feed the last

portion (as short as possible),

through one of the slots in the

mounting area (Figure 2).

Figure 2

Figure 1

4Install telephone

base on wall jack

Hold the base up

next to the wall jack,

and plug in the line

cord (Figure 3).

Then push the base

against the wall jack

and down until it is

held securely by the

mounting studs.

NOTE: If you

cannot fit the base

onto the wall jack,

remove the four

non-slip pads.

5Set DIAL mode switch

Refer to Step 4 in “Table/Desk Installation.”

6 Connect handset to telephone

Connect one end of the coiled handset cord into

the base. Plug the other end into the handset

(Figure 4). Then hang up.

7 Check for dial tone

Lift the handset and listen for dial tone. If you

cannot hear a dial tone, refer to “In Case of

Difficulty” and try to correct the problem.

MEM

THIS NO.

MEM

THIS NO.

MEM

Figure 4

Figure 3

OPERATION

Redial

This telephone stores in memory the last phone

number dialed. However, if the phone is unplugged

from the line jack for 30 minutes or more, redial

memory will be lost.

The redial memory can accept numbers up to 31

digits long. The number will remain in memory until

you change it by dialing another telephone number.

To dial the same number again, lift the handset, and

press .

NOTE: If the number is more than 31 digits long,

no digits will be stored in the redial memory.

Erasing Redial

For privacy, you can erase the redial memory. Lift the

handset, then press and hang up.

Flash

Press instead of pressing the switchhook to

activate custom calling services such as call waiting

or 3-way calling.

You may have to press other buttons before or after

as explained in custom calling instructions

provided by your local telephone company.

FLASH

REDIAL

Mute

While on a call, press to mute the

microphone. The other party cannot hear you, but

you can hear the other party.

Press again to return to two-way

conversation.

Ringer Volume

The RINGER volume switch allows you to turn the

telephone ringer OFF, or set it to ring at LO or HI

volume. You can dial or answer calls normally when

the ringer is off. Other telephones in your home will

still ring; they are not affected by the switch.

Select Ringer Tone

You can select from three different ringer tones. The

phone comes set to Tone 2.

1Press .

2Press .

3Press for Tone 1

–OR–

Press for Tone 2

–OR–

Press for Tone 3.

4Press to save your selection.

Receiver (Handset) Volume

The RECEIVER volume switch on the side of the

handset can be adjusted for a comfortable listening

level. The switch has three volume positions.

PROG/MUTE

Temporary Tone Dialing

Temporary tone dialing is used only when you have

rotary service. It allows you access to services that

require tone signaling, including some tone-activated

computer systems (e.g., telephone banking).

To change from pulse (rotary) to tone dialing during a

call:

1Dial a telephone number with the DIAL switch set

to DP (pulse).

2Press t; all buttons pressed after this will

send tone signals.

3After you hang up, the phone automatically

returns to rotary service.

MEMORY DIALING

Memory Features

This telephone can store up to 13 different phone

numbers, each up to 21 digits long. Numbers will

remain stored in memory unless you erase or change

them by entering other numbers.

NOTE: Numbers programmed into a memory

location might not be retained if the telephone has

been unplugged from the line jack for a half hour or

more.

Directory Card: Remove the directory card. Write

your telephone number in the space provided. Also

write the telephone numbers (or names) that you want

to store in each memory location. Reinstall the card

and clear plastic cover.

MEM

THIS NO.

One-Touch Dialing

Three numbers can be stored in one-touch memory

locations . You can dial these numbers by pressing

one of the buttons marked with an emergency symbol

( , or ).

To program numbers into memory

4Enter telephone number. You will hear a click

when each button is pressed.

5Press

6Hang up after the number is entered correctly.

7Repeat Steps 1–6 to store another number.

To dial

1Listen for dial tone.

2Press the one-touch memory button

( , or ).

PROG/MUTE

1Lift the

handset.

2Press .

PROG/MUTE

3Press the

one-touch

memory

button

where the

number is

to be

stored.

Speed Dialing

Ten telephone numbers can be stored in standard

speed-dialing locations. You can dial any of these

numbers by pressing two buttons.

To program numbers into memory

1Lift the handset.

2Press .

3Press .

4Enter a digit (0-9) for the memory location where

the number is to be stored.

5Enter telephone number. You will hear a click

when each button is pressed.

6Press .

7Hang up after the number is entered correctly.

8Repeat Steps 1–7 to store another number.

To dial

1Listen for dial tone.

2Press .

3Press memory location (0-9).

Memory Erase

To erase any number from memory, you can enter

another number in the same location.

MEM

PROG/MUTE

MEM

PROG/MUTE

Andere Handbücher für TRIMLINE 210

Inhaltsverzeichnis

Andere AT&T Telefon Handbücher

AT&T

AT&T ATT1856 Bedienungsanleitung

AT&T

AT&T CL82113 Bedienungsanleitung

AT&T

AT&T 924 Bedienungsanleitung

AT&T

AT&T MERLIN 206 Bedienungsanleitung

AT&T

AT&T E5865 Bedienungsanleitung

AT&T

AT&T 1856 - Corded Speakerphone Bedienungsanleitung

AT&T

AT&T ML17939 Bedienungsanleitung

AT&T

AT&T BELL 540 Series Einrichtungshandbuch

AT&T

AT&T 874 Bedienungsanleitung

AT&T

AT&T 1856 - Corded Speakerphone Bedienungsanleitung

AT&T

AT&T E5965C Bedienungsanleitung

AT&T

AT&T Small Business System Speakerphone Bedienungsanleitung

AT&T

AT&T CN5345 Bedienungsanleitung

AT&T

AT&T MERLIN LEGEND MLX-10 Non-Display Telephone Bedienungsanleitung

AT&T

AT&T Trimline TR1909B Bedienungsanleitung

AT&T

AT&T TL92271 Bedienungsanleitung

AT&T

AT&T 927 Bedienungsanleitung

AT&T

AT&T SynJ SB67138 Bedienungsanleitung

AT&T

AT&T 1175 Bedienungsanleitung

AT&T

AT&T CareLine SN1197 Bedienungsanleitung

AT&T

AT&T 957 Bedienungsanleitung

AT&T

AT&T Syn248 SB35031 Bedienungsanleitung

AT&T

AT&T Synapse SB67020 Bedienungsanleitung

AT&T

AT&T CL83101 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung

Axess Telecom

Axess Telecom ACW-1xP800 Bedienungsanleitung