ATD Tools ATD-7332A Gebrauchsanweisung

Model: ATD-7332A

Capacity: 3-1/2 Ton

ATD-7332A

3-1/2 Ton Hydraulic Service Jack

Capacity Min. Height Max Height Handle

Length

Overall

Length

Overall

Width

Saddle

Diameter

Shipping

Weight

3-1/2 Ton 3-3/4” 21-3/4” 49-1/4” 31-1/8”

Contents:

Page: 1. Speci ca ons

2. Safety & Warning Informa on

3. & 4. Setup, Opera on & Preven ve Maintenance

5. Inspec on, Storage & Troubleshoo ng

6. Exploded View & Replaceable Part Numbers

7. Warranty Informa on

8. Preven ve Maintenance Record Log

Opera ng Instru ons & Parts Manual

14” 4-3/4” 107 LB

ATD7332A_rev_0417

Made in China to ATD Tools, Inc. Specications

Visit us at www.atdtools.com

WARNING: This product may contain chemicals, including lead, known to the State of California

to cause cancer, birth defects or other reproductive harm. Wash hands after handling.

Model: ATD-7332A

Capacity: 3-1/2 Ton

SAFETY & WARNING INFORMATION

IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE

Before opera ng this device, be sure to read all content within this manual, ensuring that you

understand the opera ng procedures, maintenance requirements, and all safety warnings.

The owner and/or operator shall have an understanding of the product, its opera ng

characteris cs, and safety opera ng instruc ons before opera ng this device. Safety

informa on shall be emphasized and understood. If the operator is not uent in English, the

product and safety instruc ons shall be read to and discussed with the operator in the

operator’s na ve language by the purchaser/owner or his designee, making sure that the

operator comprehends their contents.

Actions to help prevent dangerous situations

Study, understand, and follow all instruc ons before opera ng this device.

Do not exceed the rated capacity stated.

Use only on hard level surfaces.

This item is to be used as a li ing device only. Immediately a er li ing, support the vehicle

with appropriate means.

Do not move or dolly the vehicle while it is on the jack.

Li only on areas of the vehicle as speci ed by the vehicle manufacturer.

No altera ons shall be made to this product.

Failure to heed these markings may result in serious personal injury and/or property

damage.

This is the safety n con

symbol. This symbol will n fy you

of any poten al injury hazards.

Please follow all instruc ons that

follow this symbol to avoid possible

injuries or death.

Indicates a hazardous

situa on. If proper steps are

not followed, death or

serious injury could result.

Model: ATD-7332A

Capacity: 3-1/2 Ton

SETUP, OPERATION & PREVENTIVE MAINTENANCE

Setup

Prior to each use, visual inspec on (See Pg. 5) shall be made to the device by checking

for abnormal condi ons, such as cracked welds, leaks, and damaged, loose, or missing

parts.

Consult the vehicle owner’s manual to determine the loca on of li points.

Be sure to set the vehicle in park with the emergency brake on and wheels securely

chocked.

Be sure that the vehicle and the jack are on a hard, level surface.

Assembly

If two piece handles are provided, assemble the upper sec on into the lower sec on,

line up the holes, insert and ghten the screw.

Insert the bo om end of handle into handle fork and securely ghten the bolt and

washer. Ensure the handle can turn freely.

Lifting

Turn the handle/release valve clockwise to the closed posi on. Do not over ghten.

Posi on the jack under the speci ed li point.

Begin li ing by pumping the handle up and down.

Immediately a er li ing, support the vehicle with appropriately rated jack stands.

Turn the handle/release valve slowly counterclockwise to lower the vehicle onto jack

stands.

Lowering

Turn the handle/release valve clockwise to the closed posi on. Do not over ghten.

Pump the handle up and down to li vehicle o jack stands.

Remove the jack stands. Do not get under or let anyone get under the vehicle while

lowering.

Turn the handle/release valve slowly counterclockwise to lower the vehicle onto the

ground.

Model: ATD-7332A

Capacity: 3-1/2 Ton

SETUP, OPERATION & PREVENTIVE MAINTENANCE (Cont.)

Maintenance

NOTICE: Use high grade hydraulic oil only. Never use brake uid, motor oil, transmission uid,

turbine oil or any other uids. ISO-VG22 or equivalent hydraulic oil is recommended.

Check and Refill Oil

With the jack in the fully lowered and in level on, if unit cover is provided, remove unit

cover, then remove oil ller plug.

Proper oil level should be just covering inner cylinder as seen from the oil er plug hole.

Do not over Always ll with new, clean hydraulic jack oil as recommended above.

Reinstall oil r plug, then reinstall unit cover.

Lubrication and Cleaning

Periodically clean and lubricate all moving parts and pivot points.

Air Venting Procedures

With the jack in the fully lowered on, release valve open, remove oil er plug.

Pump the handle rapidly several mes. Reinstall oil er plug.

Turn the handle/release valve clockwise to the closed posi on.

Pump the handle un the li arm reaches maximum height and co nue to pump

several mes to remove trapped air in the system.

Turn the handle/release valve counterclockwise in one full turn and lower arm to the

lowest posi on. Use force on saddle if necessary.

Carefully and slowly loosen oil ler plug to release pressurized air.

Repeat above steps un l trapped air is completely vented.

Damaged Equipment

Any jack that appears to be damaged in any way, is found to be worn, or operates abnormally

SHALL BE REMOVED FROM SERVICE UNTIL REPAIRED. It is recommended that necessary

repairs be made by a manufacturer’s or supplier’s authorized repair facility if repairs are

permi ed by the manufacturer or supplier.

Alterations

Because of poten al hazards associated with this type of equipment, no altera ons shall be

made to the product.

Attachments and Adapters

Only a achments and/or adapters supplied by the manufacturer shall be used.

Model: ATD-7332A

Capacity: 3-1/2 Ton

INSPECTION, STORAGE & TROUBLESHOOTING

Inspection

Visual inspec on shall be made before each use of the device by checking for abnormal

cons, such as cracked welds, leaks, and damaged, loose, or missing parts.

Other inspec ons shall be made per product opera ng instruc ons.

This device shall be inspected immediately if the device is believed to have been

subjected to an abnormal load or shock. It is recommended that this inspec be made

by a manufacturer’s or supplier’s authorized repair facility.

Owners and/or operators should be aware that repair of this equipment may require

specialized knowledge and es. It is recommended that an annual inspec on of the

product be made by a manufacturer’s or supplier’s authorized repair facility and that

any defec ve parts, decals, or safety labels or signs be replaced with manufacturer’s or

supplier’s speci ed parts.

Storage

This Jack should be stored in a dry loca on on a level surface.

Troubleshooting

Symptom Possible Causes Solu on

Jack will not li the load. 1. Release valve not ghtly closed.

2. Low oil level.

3. Defe ve or worn internal parts.

4. Load exceeds maximum

allowance.

1. Tighten release valve.

2. Check and add oil. Follow “Check

and Oil” instru ns on Pg.4.

3. Disc nue use and contact a

local repair center.

4. Use a higher capacity jack.

Jack will not hold the load. 1. Release valve not ghtly closed.

2. Power unit malfunc on.

1. Tighten release valve.

2. Disc nue use and contact a

local repair center.

Jack will not descend to

minimum height, or will not

remain in lowered posi on.

1. Air trapped in system.

2. Reservoir oil over lled.

1. Vent air out of system. Follow “Air

Ve ng Procedures” above.

2. Check and ensure proper oil level.

Follow “Check and Oil”

instru n on Pg.4.

Jack will not li to max

height.

1. Low oil level. 1. Check and ensure proper oil level.

Follow “Check and Oil”

instruc ns on Pg. 4.

Jack will not fu on

properly a er tried solu n.

1. Internal malfunc on or structural

damage.

1. Stop usage and contact an

authorized repair center.

Model: ATD-7332A

Capacity: 3-1/2 Ton

EXPLODED VIEW & REPLACEABLE PART NUMBERS

* Items not iden ed by part number are not available for replacement.

Item Part Number* Descrip on Q’ty

1LYD3G-100 Front wheel assembly 2

21dap/welddaSA005-G3DYL

3GB308-84-#6 Grease Fi 1gn

41revoC3-J3DYL

LYDBI-3T-17

Handle Assembly w/ foam 1

62gnirpSnruteRA9-2DYL

7LYDBI-3T.4 Power Unit Assembly 1

8LYD3G-300 Handle Fork Assembly 1

9LYD3G-400 Rear Caster Assembly 2

LYD3F-102A

Handle foam only 1

11 LYD3K-1 Saddle pad only 1

N/A 1lebaLtcudorPL-A2337DTA

WARRANTY INFORMATION

ONE YEAR LIMITED WARRANTY

For a period of one (1) year from your purchase date, ATD Tools Inc. will repair or

replace (at its option) without charge, your ATD product if it was purchased new and the product

has failed due to a defect in material or workmanship which you experienced during normal use

of the product. This limited warranty is your exclusive remedy.

To access the benefits of this warranty, contact your ATD Tools, Inc. supplier for confirmation

that this warranty applies. Thereafter, you may be advised to return the product under warranty,

freight prepaid, to the ATD service department.

If this ATD product is altered, abused, misused, modified, or undergoes service by an

unauthorized technician, your warranty will be void. We are not responsible for damage to

ornamental designs you place on this ATD product and such ornamentation should not cover

any warnings or instructions or they may void the warranty. This warranty does not cover

scratches, superficial dents, and other abrasions to the paint finish that occur under normal use.

Subject to the law in your state:

(1) Your sole and exclusive remedy is repair or replacement of the defective product as

described above.

(2) ATD is not liable for any incidental damages, including but not limited to, lost profits and

unforeseeable consequences.

(3) The repair and replacement of this product under the express limited warranty described

above is your exclusive remedy and is provided in lieu of all other warranties, express or

implied. All other warranties, including implied warranties and warranties of

merchantability or fitness for a particular purpose are disclaimed and, if disclaimer is

prohibited, these warranties are limited to one year from your date of purchase of this

product.

Some states’ laws do not allow limited durations on certain implied warranties and some states’

laws do not allow limitations on incidental or consequential damages. You should consult the

law in your state to determine how your rights may vary.

Model: ATD-7332A

Capacity: 3-1/2 Ton

Made in China to ATD Tools, Inc. Specifications

Visit us at www.atdtools.com

Warranty Service Number 1-844-364-9922

For Non-warranty issues, please contact your supplier.

Printed In China

Model: ATD-7332A

Capacity: 3-1/2 Ton

PREVENTIVE MAINTENANCE RECORD LOG

Date Maintenance Performed

Inhaltsverzeichnis

Andere ATD Tools Jack Handbücher

ATD Tools

ATD Tools ATD-7462 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7447 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-2025 Bedienungsanleitung

ATD Tools

ATD Tools 7392 Gebrauchsanweisung

ATD Tools

ATD Tools 7514 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7328 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7435 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7396 Gebrauchsanweisung

ATD Tools

ATD Tools 7434A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7385W Bedienungsanleitung

ATD Tools

ATD Tools ATD-7435A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7438 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7423W Bedienungsanleitung

ATD Tools

ATD Tools ATD-7382W Bedienungsanleitung

ATD Tools

ATD Tools ATD-7406 Gebrauchsanweisung

ATD Tools

ATD Tools 7343 Bedienungsanleitung

ATD Tools

ATD Tools Atd-7430 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7433A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7380 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7461 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7384W Bedienungsanleitung

ATD Tools

ATD Tools 7380 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7500 Gebrauchsanweisung

ATD Tools

ATD Tools SwiftLift ATD-7325 Gebrauchsanweisung

Beliebte Jack Handbücher anderer Marken

Omega Lift Equipment

Omega Lift Equipment 18122C Gebrauchsanweisung

Pittsburgh

Pittsburgh 58816 Montageanleitung

Unimec

Unimec TP Bedienungsanleitung

Sonic

Sonic 4800703 Bedienungsanleitung

BGS technic

BGS technic 70039 Bedienungsanleitung

TradeQuip

TradeQuip 1128T Bedienungsanleitung

VEVOR

VEVOR TJD-12000SP-F Bedienungsanleitung

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Bedienungsanleitung

Stels

Stels 51131 Bedienungsanleitung

Bushranger

Bushranger RJX01 Bedienungsanleitung

Clarke

Clarke CTJ2500QLG Installations- und Betriebshandbuch

Valex

Valex 1650520 Bedienungsanleitung

Pfaff

Pfaff Merkur M0 Bedienungsanleitung

Beta

Beta 3050/K Beilage

Sealey

Sealey 1050CXHV Bedienungsanleitung

Jung

Jung JH Series Bedienungsanleitung

URIAH

URIAH UC200020 Bedienungsanleitung

Kennedy

Kennedy KSJ010 Bedienungsanleitung