Atdec AWM 710 Arm Bedienungsanleitung

AWM-A71T Page 1 of 4

Installation Guide

AWM-A71T

AWM 710 Arm

COMPONENT CHECKLIST

Monitor Arm

(x1)

VESA Head

(x1)

Channel Clamp

(x1)

Screw

M4x10mm

(x4)

Security

Screw

(x1)

4mm

Allen Key

(x1)

REQUIRED TOOLS

WEIGHT RANGE

• Phillips Head Screwdriver

Monitor weight should be within the

weight range of all modular elements

that make up the complete monitor

mounting solution.

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! Do not remove or throw away the plastic sleeve on the channel clamp.

! The manufacturer accepts no responsibility for incorrect installation.

! This product is compatible with Atdec AWM Series Posts and Wall Channels

! This product is not suitable for outdoor use or mobile applications

! Do not over-tighten screws and adjustment points on product.

! VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA locations, and unevenly weighted monitors

(relative to the center of the VESA mounting interface) exert additional leverage that can exceed the capacity of the mount even

though the monitor weight may be within the stated range. Please contact Atdec if you would like further information.

Flat Monitor

0 - 9kg

(0 - 20lb)

Curved Monitor

0 - 9kg

(0 - 20lb)

Curved monitors with an overall

depth up to 140mm (5.5”).

AWM-A71T Page 2 of 4

1. Fix channel clamp to post or wall channel

1.1 Ensure knob is undone. 1.2 Slide channel clamp into channel.

Push knob to

aid insertion

1.3 Hold clamp in desired position on

channel and turn knob to lock in place.

1. Ensure Knob is undone

3. Fit arm onto channel clamp

Note: Check the

arm rotation is

smooth after

tightening.

3.1 Push arm onto shaft. 3.2 Ensure arm is fully pushed onto shaft. 3.3 Tighten joint screw.

2. Ensure arm is fully pushed onto clamp

3. Tighten set screw

Tip: Check the

arm rotation is

smooth after

tightening.

IMPORTANT

Ensure plastic

sleeve is tted

on clamp

3. Place the rotation ring

in the desired postion

2. OPTIONAL Set arm rotation to 180°

2.1 Remove plastic sleeve

from channel clamp.

2.2 Remove rotation ring. 2.3 Place rotation ring in desired position and replace plastic sleeve

Note: rotation ring placement

depends on the position of the clamp

on the post. The tag on the ring

should always face toward the user.

1. Remove plastic sleeve

2. Remove rotation ring

1. Press

2. Lift

Note rotation is set to 360° by default.

180°

360°

Default

Position

Flipped

Position

Tag

AWM-A71T Page 3 of 4

6. Monitor arm cable management

Important

Ensure enough

cable slack is

given to allow

for movement

of the monitor

6.1 Plug cables into the monitor

and route the cables down the arm

using the cable hooks and clips.

4. Attach VESA head to monitor

Too long

Monitor

VESA Plate

VESA Screw

Too short

4.2 Attach VESA head

onto monitor with

provided screws.

(Alternatively, use

fasteners specied

by the monitor

manufacturer)

4.1 Check VESA mounting

compatibility of monitor

100mm

75mm

100mm

75mm

Note: For other sizes, use

a suitable adaptor plate

(sold separately).

Note: Recessed 75x75

VESA interfaces will

require a Spacer Kit

(sold separately)

Note: ensure screw length

suits the monitor VESA

mounting holes.

5. Attach monitor to arm

5.1 Fit monitor onto arm.

Note: VESA Head will

automatically latch

onto the tilt head.

Click

5.2 OPTIONAL SECURITY SCREW

If desired, once monitor is attached to the

arm, Install the security screw. This disables

the release switch, preventing theft.

AWM-A71T Page 4 of 4

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

DO NOT OVERTIGHTEN

Increasing tension only stiffens

movement and cannot lock off

arm movement.

TIGHTEN LOOSEN

7. OPTIONAL Adjust tilt tension

Note: Support

monitor while

adjusting.

7.1 Factory set tilt tension will be

suitable for most monitors.

If required, adjust the tilt tension

using the 4mm hex key.

TIGHTEN

LOOSEN

8. OPTIONAL Adjust rotation tension

8.1 Tune the rotation tension

using 4mm hex key.

Adjustment may only be

required for ultrawide monitors.

HOLDS POSITIONDROOPS FORWARD

HOLDS POSITIONDRIFTS

9.1 Arm movement can be

adjusted to be rmer or more

free. Use the 4mm hex key to

adjust the tension of the three

pivot joints on the arm.

9. OPTIONAL Adjust arm joint tension

10. Removing monitor

10.1 Slide release switch up and

click into unlocked position, then

lift monitor away from the arm.

Click

Slide

Andere Atdec Rack & Stand Handbücher

Atdec

Atdec AWM-LR Bedienungsanleitung

Atdec

Atdec Levitate Betriebsanleitung

Atdec

Atdec VFS-DH Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-FS Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-FS Bedienungsanleitung

Atdec

Atdec AWMS-DW Bedienungsanleitung

Atdec

Atdec AD-TVC-45 Bedienungsanleitung

Atdec

Atdec ADBS-4x1-39TW Merkblatt

Atdec

Atdec AWM-A71 Bedienungsanleitung

Atdec

Atdec AD-TVAC-CM Bedienungsanleitung

Atdec

Atdec VFS-DH Bedienungsanleitung

Atdec

Atdec AD-TVAC-CM Bedienungsanleitung

Atdec

Atdec ADBS-3x1-30T3C Bedienungsanleitung

Atdec

Atdec Visidec Focus Articulated Arm Wall Betriebsanleitung

Atdec

Atdec AF-WD Bedienungsanleitung

Atdec

Atdec AWMS-46W35 Bedienungsanleitung

Atdec

Atdec TH-1040-CTS Bedienungsanleitung

Atdec

Atdec Visidec Freestanding Double Bedienungsanleitung

Atdec

Atdec Visidec Focus Micro Betriebsanleitung

Atdec

Atdec AWM-W6 Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-G Bedienungsanleitung

Atdec

Atdec AWM-LR Bedienungsanleitung

Atdec

Atdec Freestanding Quad Bedienungsanleitung

Atdec

Atdec TH-3060-UFL Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung