Atdec AWMS-2-BT75-FS Bedienungsanleitung
AWMS-2-BT75-FS Page 1 of 4
Installation Guide
AWMS-2-BT75-FS
COMPONENT CHECKLIST
B
Bridge
(x1)
C
Leg
(x2)
A
Post
(x1)
D
Bracket
(x2)
F
4mm/6mm
Hex Key
(x1 each)
E
VESA Plate
(x2)
G
M8x30mm
Cap Screw
(x4)
J
M8x80
Cap Screw
(x2)
I
M8 Washer
(x2)
L
M4x10 Screw
(x8)
K
Post Cap
(x1)
M
M4x20 Screw
(x8)
N
10mm Spacer
(8x)
H
M8 Nut
(x4)
IMPORTANT INFORMATION
! Product should only be assembled and used as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! EachBracketsupportsamaximumweightasperabovecapacityspecication.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! Do not move mount with displays attached.
! VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA locations exert additional leverage that can
exceed the capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you
would like further information.
! WARNING! Death or serious injury may occur if a child climbs on or tips product. Anchor product if applicable. Never place
product in an unstable location.
Freestanding Heavy Duty
Dual Vertical Monitor Mount
REQUIRED TOOLS
• Phillips Head Screwdriver
CAPACITY
Flat Monitor
4.5 - 25kg (10 - 55lb)
Curved Monitor
4.5 - 18kg (10 - 40lb)
Display Size
24” - 55”
300mm (12”) max overall
display depth
Scan to access
more information
AWMS-2-BT75-FS Page 2 of 4
2. Attach Post to Base
2.1 Insert M8x80 Cap Screws (x2)
through M8 Washers and holes in
Base then fasten to Post.
Tightenrmly.
I
J
A
1. Assemble Base
1.1 Align Bridge holes and Leg
holes. Use 6mm Hex Key.
Hold M8 Nut in hexagonal
recess until M8x30 Cap Screw
engages. Tighten screw.
65%
A
B
G
H
1.2 Repeat on
opposite Leg.
2.2 Remove clips and covers
from post by sliding up and out
or by squeezing sides.
NOTE:
Rest short end of Bridge on a
soft surface while fastening
C
B
G
H
F
65%
A
B
G
H
NOTE:
Assemble with Cable Covers facing backwards
(Towards the small side of Base)
SQUEEZE
to release
I
J
A
75mm
100mm
75mm
100mm
NOTE:
For 75mm VESA unscrew
5mm to access top holes
3.2 Attach VESA Plate
with M4x10 Screws.
3.2 For recessed VESA use
10mm Spacers and M4x20
screws.
OR
3.1 VESA compatibility.
NOTE:
Some displays require the use of
a VESA adapter before attaching
the VESA Plate. This VESA adapter
may ship in the box with the display.
Consult your display’s installation
guide for further information.
3. Attach VESA Plates to Displays
E
L
TOP
E
M
N
AWMS-2-BT75-FS Page 3 of 4
5. Attach Bottom Display
5.1 Set VESA Plate to
open position.
Bottom display must be
attachedtoBracketrst.
WARNING:
Use two people to install
display
OPEN
WARNING:
Do not loosen
hand knob once
display attached
5.4 Set VESA Plate to closed
position by sliding clips on
both sides inwards.
5.5 Adjust display tilt
angle by gripping edges
of screen and rolling up or
down to desired position.
OPEN
TILT KNOBS
5.6 Set display
angle by tightening
tilt knobs.
F
OPTIONAL
ADJUSTMENT -
TILT FRICTION
Clockwise = More friction
Anticlockwise = Less friction
4mm Hex Key can
be used to reduce
tilt friction (for
light screen) or
increase tilt friction
(for heavy screen)
5.3 Centre VESA Plate
close to Post and slowly
lower until bar on VESA
Plate sits in saddle in
Bracket.
5.2 Place mount on the
stable surface where it
will be used.
Lift display until VESA
Plate is above the
Bracket.
CLOSED
4. Slide Brackets onto Post and Set Height
4.1 Line up the inner guide
on rear of Bracket with rear
channel on Post.
Slide inner guide into channel,
then lower Bracket.
D
TIGHTEN
WARNING:
Never loosen knob while
display is on bracket
DMEASURE
≥Display
height
between
brackets
K
MEASURE to
ensure clearance
to base
4.2 Firmly tighten hand knob at
chosen height.
Ensureheightissufcientfor
screen to clear base once in place.
Repeat with second bracket and t
Post Cap.
MEASURE
≥Display
height
between
brackets
K
MEASURE to
ensure clearance
to base
AWMS-2-BT75-FS Page 4 of 4
7. Fine Adjustment
6. Attach Top Display
ii
iii
iv
i
LHS &
RHS
TOP &
BOTTOM
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reservestherighttoalterspecicationswithoutnotice.©20221125
6.1 Check that distance
between Brackets is
equal to or greater than
the height of the display.
Repeat Step 5 to attach
top display and set tilt
angle.
Lower
Close
Adjust angle
Set angle
i
ii
iii
iv
Unstacked Stacked
Cables can
exit from
the side of
the cable
cover
PUSH
PUSH
PUSH
8. Cable Management
8.1 Load cables into
cable clip.
8.2 Insert one side of the
cable clip into a channel
on the post, then push in
the other side.
Load cables into
cable cover
8.3 Load
cables into
cable cover.
8.3 Clip the cable cover
back onto rear post
channels.
7.1 To correct horizontal angle
of display +/- 3 °:
Turnasinglenetune
adjustment knob to adjust
angle of screen.
Clockwise = Higher
Anti-clockwise = Lower
7.2 To close small gap between
displays +/-6mm (1/4”):
Turnbothnetuneadjustment
knobs - alternating sides a few
rotations at a time.
Clockwise = Higher
Anti-clockwise = Lower
ii
iii
iv
i
LHS &
RHS
TOP &
BOTTOM
FINE HEIGHT ADJUST
FINE ADJUSTMENT
KNOBS
NOTE:
Ensure clips are in
CLOSED position
WARNING:
Always remove displays
before moving mount
Andere Atdec Rack & Stand Handbücher
Atdec
Atdec AWM-LC Bedienungsanleitung
Atdec
Atdec AWMS-3-137140-C Bedienungsanleitung
Atdec
Atdec TH-2050-VFM Bedienungsanleitung
Atdec
Atdec AF Series Bedienungsanleitung
Atdec
Atdec AWM-LR Bedienungsanleitung
Atdec
Atdec AWM Series Bedienungsanleitung
Atdec
Atdec AF-AT Bedienungsanleitung
Atdec
Atdec AD-AC-PH Bedienungsanleitung
Atdec
Atdec AWM-WS Bedienungsanleitung
Atdec
Atdec TELEHOOK 12/30 Multi Bedienungsanleitung
Atdec
Atdec AF-AT-NBC Bedienungsanleitung
Atdec
Atdec SYSTEMA SW6S Bedienungsanleitung
Atdec
Atdec AWM-P G Bedienungsanleitung
Atdec
Atdec AF-ATC Bedienungsanleitung
Atdec
Atdec AWM-W6 Bedienungsanleitung
Atdec
Atdec AF-MC Bedienungsanleitung
Atdec
Atdec Visidec Focus Micro Betriebsanleitung
Atdec
Atdec VFS-DV Bedienungsanleitung
Atdec
Atdec AWMS-2-BT75-FS Bedienungsanleitung
Atdec
Atdec AWMS-2-4640-C Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
