ATI Technologies 39-0215 Bedienungsanleitung

ATL HDX Active Sync Manual

Version - 1.1

Date - October 2017

Part Number - 39-0215

Innovation In and

Out of Parlour

Good Practice 2

ATL V2.00 HDX Reader Synchronisation Connections: 3

ATL V3.00 HDX Reader Synchronisation Connections: 4

GOOD PRACTICE: Control, Power and Data Cables and Conduit.

Cables must be kept as short as possible running directly from point to point. Cut out any

excess cable rather than leaving it coiled.

Where ever possible cables should be contained in a waterproof conduit using the correct

csa cable specified in the diagrams.

Entries must be made into the bottom of power supply or control casings but never into the

top. This will invalidate the warranty.

Strip existing cables back to bright copper before connection.

Keep multicore cables away from other cables especially those carrying mains or heavy

currents. Cross only at 90 where necessary and do not enclose in conduit with other cables.

Keep feeder cables and coaxial cables in separate conduits.

Make sure diodes are fitted to all feeders, pulsators and solenoid valve. These should be

fitted as close as possible to feeder motor or solenoid coil.

INDEX

The ATL HDX Reader

The ATL HDX reader can be found in all ATL products which use automatic identification. Examples are parlour auto-id systems, Pegasus sorting gate systems and out of parlour feeding systems.

If an ATL HDX reader and a non-HDX reader are in close proximity, they may interfere with one another and adversely affect performance. In order to overcome this, the readers need to be

synchronised together. This can be achieved by using the Active Sync and connecting into the synchronisation port as shown in the diagram below.

Innovation In and Out of Parlour

2 | ATL HDX Active Sync Manual | v1.1

ATL V2.00 HDX Reader Synchronisation to Non-ATL HDX Reader

WARNING: DO NOT RUN TWISTED PAIR

DATA CABLE NEXT TO MAINS CABLES OR

CABLES CARRYING HIGH CURRENT AS

WILL CAUSE INTERFERENCE AND SYSTEM

WILL NOT FUNCTION CORRECTLY.

V2.00.03

16-12-08

+12v In

Out

Active Sync Unit

+0V In

Master / Slave Jumper Settings

= Master

= Slave

Master / Slave Jumper

*see below

Sync Port

Ground

+12v

The jumper should be set to slave to synchronise.

Place Active Sync PCB in close proximity to

the non-ATL HDX reader antenna.

Innovation In and Out of Parlour

3 | ATL HDX Active Sync Manual | v1.1

ATL V3.00 HDX Reader Synchronisation to Non-ATL HDX Reader

WARNING: DO NOT RUN TWISTED PAIR

DATA CABLE NEXT TO MAINS CABLES OR

CABLES CARRYING HIGH CURRENT AS

WILL CAUSE INTERFERENCE AND SYSTEM

WILL NOT FUNCTION CORRECTLY.

V3.02

+12v In

Out

Active Sync Unit

+0V In

Master / Slave Switch (Switch 1)

Set to ON to synchronise

Sync Input Pin

Ground

+12v

Place Active Sync PCB in close proximity to

the non-ATL HDX reader antenna.

Innovation In and Out of Parlour

4 | ATL HDX Active Sync Manual | v1.1

1 2 3 4

Inhaltsverzeichnis

Andere ATI Technologies Messgerät Handbücher

ATI Technologies

ATI Technologies Q-Card Technisches Datenblatt

ATI Technologies

ATI Technologies 2i Bedienungsanleitung

ATI Technologies

ATI Technologies Q46P Bedienungsanleitung

ATI Technologies

ATI Technologies 39-0080 Bedienungsanleitung

ATI Technologies

ATI Technologies Q46 Series Bedienungsanleitung

ATI Technologies

ATI Technologies Q45R Bedienungsanleitung

ATI Technologies

ATI Technologies A15/82 Bedienungsanleitung

ATI Technologies

ATI Technologies Q46H/65 Bedienungsanleitung

ATI Technologies

ATI Technologies Q46F/82 Bedienungsanleitung

ATI Technologies

ATI Technologies Q46 Series Gebrauchs- und Pflegehandbuch

ATI Technologies

ATI Technologies Q46 Series Gebrauchs- und Pflegehandbuch

ATI Technologies

ATI Technologies Q46H/79PR Bedienungsanleitung

ATI Technologies

ATI Technologies TDA-110P Handbuch

ATI Technologies

ATI Technologies Q45D Bedienungsanleitung

ATI Technologies

ATI Technologies Scorpion X2 Bedienungsanleitung

ATI Technologies

ATI Technologies C12-17 Bedienungsanleitung

ATI Technologies

ATI Technologies 39-0050 Leitfaden

ATI Technologies

ATI Technologies Metrinet Bedienungsanleitung

ATI Technologies

ATI Technologies SmartTachSmartTach Bedienungsanleitung

ATI Technologies

ATI Technologies Q45D Bedienungsanleitung

ATI Technologies

ATI Technologies 39-0062 Bedienungsanleitung

ATI Technologies

ATI Technologies PQ45H Bedienungsanleitung

ATI Technologies

ATI Technologies Q-Blast Q46D Bedienungsanleitung

ATI Technologies

ATI Technologies Q45S/87 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung