Atlantic Alfea Excellia A.I. 024114 Bedienungsanleitung

U0611757_1876_EN_14

02/02/2023

Outdoor unit

WOYG112LHT

WOYG140LCTA

WOYK112LCTA

WOYK140LCTA

WOYK160LCTA

Hydraulic unit

024114

024115

INSTALLATION

Alféa Excellia A.I.

Air/water heat pump split 1 service

For professionals.

To be kept by the user for future reference

Heat pumps & boilers

■Installation and maintenance rules

The appliance must be installed and maintained

by an approved professional in accordance with

current regulations and codes of practice.

• Warning, hydraulic unit should not be installed

in an air current.

■Handling

The outdoor unit must not be placed in a horizontal

position during transport.

If not kept upright during transport, the appliance

could be damaged through displacement of

the refrigerant and damage to the compressor

suspension.

Any damage caused by transportation in a horizontal

position is not covered by the warranty.

If necessary, the outdoor unit may be tilted only

during manual handling (to go through a door or up

a staircase). This operation must be conducted very

carefully and the appliance must be immediately

restored to the upright position.

■Containment of refrigeration circuits

All refrigeration circuits are sensitive to

contamination from dust and moisture. If any such

pollutants penetrate the refrigeration circuit, they

can aﬀect the reliability of the heat pump.

Make sure that the connections and refrigeration

circuits (hydraulic unit, outdoor unit) are

protected correctly.

In the event of a subsequent failure and following

an inspection, the presence of moisture or

foreign bodies in the compressor oil would

automatically void the warranty.

- Check upon receipt that the ﬁttings and refrigeration

circuit caps mounted on hydraulic unit and outdoor

unit are properly seated and secured (cannot be

loosened with bare hands). If this is not the case,

tighten them using a C spanner.

- Check also that the refrigeration connections are

sealed (plastic caps or tubes crimped at the ends

and brazed). If the caps must be removed during

the installation (tubes to be re-cut for example),

put them back as soon as possible.

■Hydraulic connections

The connection must comply with industry standard

practice according to current regulations.

Remember: Seal everything when ﬁtting in

accordance with industry standard practice for

plumbing work:

- Use suitable seals (ﬁbre gasket, O-ring).

- Use Teﬂon or hemp tape.

- Use sealing paste (synthetic depending on the

case).

Use glycol/water mix if the minimum ﬂow

temperature is set below 10°C. If you are using a

glycol/water mix, arrange for an annual check on

the quality of the glycol. Use monopropylene glycol

only. The recommended concentration is 30%

minimum. Never use monoethylene glycol.

• In some installations, the presence of diﬀerent

metals can cause corrosion problems;

the formation of metal particles and sludge can

appear in the hydraulic circuit.

• In this case, it is advisable to use a corrosion

inhibitor in the proportions indicated by the

manufacturer.

• You must also ensure that treated water does

not become corrosive.

■Electrical connections

• Before any maintenance operation, ensure

that the general power supply is switched oﬀ.

• Speciﬁcations of electricity supply

The electrical installation must be carried out in

accordance with current regulations.

Electrical connections will only be made once all

other installation operations (fastening, assembly,

etc.) have been completed.

Warning!

The contract signed with the energy provider must

be suﬃcient not only to cover the heat pump's power

requirements but also the combined sum of all the

appliances likely to be operating at the same time. If

the power is too low, check the power rating stated

in your contract with your energy provider.

Never use a power socket for the power supply.

The heat pump must be supplied directly with power

(without external switch) by special protected leads

from the electric panel via dedicated bipolar circuit

breakers, C curve for the outdoor unit, C curve for

the electrical heating and domestic water backups

(see tables page 35).

The electrical installation must be ﬁtted with a 30mA

RCD.

This appliance is designed to operate using a

nominal voltage of 230 V +/- 10%, 50 Hz.

• General remarks on electrical connections

It is essential to maintain neutral-phase polarity

when making electrical connections.

Rigid wires are preferable for ﬁxed installations,

particularly in a building.

Tighten the cables using the cable glands to prevent

the feed wires from being accidentally disconnected.

The earth connection and its continuity must be

ensured.

• Cable glands

To ensure the stability of power (Low Voltage) and

sensor (Extra-Low Voltage) cables, it is essential

that the cable glands are tightened according to the

following recommendations:

Size of cable

gland (PE)

(mm)

Diameter of

cable

(mm)

Cable gland

tightening

torque

(check-nut)

(N.m)

Coupling net

tightening

torque

(N.m)

PG7 1 to 5 1.3 1

PG9 1.5 to 6 3.3 2.6

PG16 5 to 12 4.3 2.6

• Connecting to screw terminals

The use of ring, spade or blade terminals or

caps is prohibited.

- Always select wire that complies with current

standards.

- Bare the end of the wire to around 25 mm.

- With round end pliers, form a loop with a diameter

which matches the tightening screws on the

terminal.

- Tighten the terminal screw ﬁrmly onto the

loop created. Insuﬃcient tightening can cause

overheating, leading to breakdown or even ﬁre.

Rigid wire Loop

25 mm Spade

or blade

terminal

on ﬂexible

wire

is prohibited

Screw and special

washer

Terminal

• Connecting to controller boards

- Remove the corresponding connector and make

the connection.

Pre-cabled bundle connector and/or screw connector

• Connecting to spring terminals

- Bare the end of the wire to around 12 mm.

- Push the spring with a screwdriver so that the wire

enters the cage.

- Slide the wire into the opening provided for this

purpose.

- Remove the screwdriver and then check that the

wire stays gripped by the cage by pulling on it.

- 4 -

Contents

Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Unpacking and supplies . . . . . . . . . . . . . . . . . . . . 6

Deﬁnitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Optional equipment . . . . . . . . . . . . . . . . . . . . . . . . 6

Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . 6

General characteristics . . . . . . . . . . . . . . . . . . . . . 7

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Operating principle . . . . . . . . . . . . . . . . . . . . . . . 14

Installation 16

Installation of refrigeration connections. . . . . . . . 16

Installation of the outdoor unit . . . . . . . . . . . . . . . 18

Installation of the hydraulic unit . . . . . . . . . . . . . . 20

 Electrical connections 34

Cable dimensions and protection rating . . . . . . . 35

Electrical connections on the single phase outdoor

unit side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Electrical connections on the 3 phase outdoor unit

side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Electrical connections on the hydraulic unit side. 38

Outside sensor . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Room sensor (option) . . . . . . . . . . . . . . . . . . . . . 42

 Controller Interface 46

User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Display Description . . . . . . . . . . . . . . . . . . . . . . . 47

Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Navigating the Menus . . . . . . . . . . . . . . . . . . . . . 48

Modifying Settings . . . . . . . . . . . . . . . . . . . . . . . . 49

Temperature control . . . . . . . . . . . . . . . . . . . . . . 50

This appliance must be installed by qualiﬁed personnel holding a certiﬁcate of competence in the handling

of refrigerants.

 Description of the equipment 6

 Refrigeration connections 22

Rules and precautions. . . . . . . . . . . . . . . . . . . . . 22

Shaping the refrigeration pipes . . . . . . . . . . . . . . 22

Checks and connection . . . . . . . . . . . . . . . . . . . . 25

Filling the installation with gas. . . . . . . . . . . . . . . 26

 Hydraulic connections 30

Connecting the hydraulic unit to the heating circuit . . . 30

Filling and bleeding the installation . . . . . . . . . . . 31

Heating circulation pump speed settings. . . . . . . 32

 Commissioning 44

alfea excellia A.I. / Installation / 1876 - EN

- 5 -

 Controller Menu 52

Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Installed options . . . . . . . . . . . . . . . . . . . . . . . . . 53

Hydraulic conﬁguration . . . . . . . . . . . . . . . . . . . . 53

Heat Pump Conﬁguration . . . . . . . . . . . . . . . . . . 58

System status . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Auxiliary functions . . . . . . . . . . . . . . . . . . . . . . . . 62

Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Easy Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Basic Hydraulic Layout 70

Electrical Cabling Plans 72

 Fault Diagnosis 76

Hydraulic checks . . . . . . . . . . . . . . . . . . . . . . . . . 78

Checking the outdoor unit . . . . . . . . . . . . . . . . . . 78

Electrical checks . . . . . . . . . . . . . . . . . . . . . . . . . 78

Other maintenance 79

Emptying the hydraulic unit . . . . . . . . . . . . . . . . . 79 Distribution valve . . . . . . . . . . . . . . . . . . . . . . . . . 79

 Quick-start procedure 80

Start-up check-list . . . . . . . . . . . . . . . . . . . . . . . . 80 Commissioning technical datasheet . . . . . . . . . . 82

 Instructions for the end user 83

Faults in the Hydraulic Unit . . . . . . . . . . . . . . . . . 76 Faults in the Outdoor Unit . . . . . . . . . . . . . . . . . . 77

 Maintenance of the installation 78

alfea excellia A.I. / Installation / 1876 - EN

- 6 -

►

Packing

• 1 package: Outdoor unit.

• 1 package: Hydraulic unit and outside temperature

sensor.

►

Unpacking and supplies

While the courier is still present, carefully check the

general appearance of the appliances and check

that the outdoor unit has not been laid in a horizontal

position.

In the event of a dispute, send any relevant reservations

to the carrier in writing within 48 hours and send a copy

of the letter to Customer Services.

►

Deﬁnitions

- Split: The heat pump consists of two elements

(an outdoor unit to be installed outdoors and a hydraulic

unit to be installed inside the dwelling).

- Air/water: The surrounding air is the energy source.

This energy is transmitted to the heating circuit water

by the heat pump.

- Inverter: The fan and compressor speeds are

modulated according to the heating requirements.

This technology enables you to save on energy and

operate on a single-phase power supply, whatever

the heat pump's output, by avoiding pulling signiﬁcant

amounts of current at start-up.

- COP (Coeﬃcient of Performance): This is the

relationship between the energy transmitted to the

heating circuit and consumed electrical energy.

 Description of the equipment

alfea excellia A.I. / Installation / 1876 - EN

Packing contents list

Heat Pump Outdoor unit Hydraulic unit

Model International

Code Reference Code Reference Code

Alféa Excellia A.I. 11 526350 WOYG112LHT 700197 Alféa Excellia A.I.

single phase 024114

Alféa Excellia A.I. 14 526351 WOYG140LCTA 700175

Alféa Excellia A.I. tri 11 526352 WOYK112LCTA 700176

Alféa Excellia A.I.

3-phase 024115Alféa Excellia A.I. tri 14 526353 WOYK140LCTA 700177

WOYK140LCT 700143

Alféa Excellia A.I. tri 16 526354 WOYK160LCTA 700178

►

Optional equipment

• dual circuit kit (code 570630

(074725+075311)

)

for connecting 2 heating circuits.

• DHW kit (code 073991)

for connecting a mixed DHW tank

(with built-in electrical backups).

• Boiler connection kit (code 073989)

for connecting a boiler to the heat pump.

• Wireless room sensor A59(code 074208) for

correcting the ambient temperature.

• Wireless room sensor A75 (code 074213),

Wireless room sensor A78 (code 074214)

for correcting the ambient temperature and

programming the heat pump.

• Cooling kit (code 075328).

• High ﬂow rate circulation pump kit (code 074077)

for the installation of 1 underﬂoor heating circuit

• Anti-vibration blocks (code 523574).

• White PVC ﬂoor support (ref. 809532) or

Black rubber ﬂoor support (ref. 809536).

►

Operating Range

This heat pump provides:

- Heating in winter,

- The management of electrical backups, for extra

heating on the coldest days,

- Installation with boiler connection* for extra heating on

the coldest days,

- Management of two heating circuits*,

- Production of domestic hot water* (provided that it is

combined with a mixed DHW tank),

- Cooling in summer* (for underﬂoor heating-cooling

system or fan-convectors).

*: These options require the use of additional kits

(see chapter "Required accessory" or "Optional equipment").

- 7 -

Model name Alféa Excellia A.I. 11 14 tri 11 tri 14 tri 16

Rated heating performances (outdoor temp. / ﬂow temp.)

Heat output

+7°C/+35°C - Underﬂoor heating system kW 10.80 13.50 10.80 13.00 15.17

-7°C/+35°C - Underﬂoor heating system kW 10.38 11.54 10.38 12.20 12.98

+7°C/+55°C - Radiator kW 7.59 9.48 9.29 10.60 12.24

-7°C/+55°C - Radiator kW 7.57 9.20 9.27 10.10 12.00

Power consumption

+7°C/+35°C - Underﬂoor heating system kW 2.54 3.23 2.51 3.11 3.70

-7°C/+35°C - Underﬂoor heating system kW 4.32 5.08 4.28 5.13 5.40

+7°C/+55°C - Radiator kW 3.07 3.95 3.52 4.40 4.93

-7°C/+55°C - Radiator kW 4.57 5.08 5.09 5.65 6.89

Coeﬃcient of performance (COP) (+7°C/+ 35°C) 4.25 4.18 4.30 4.18 4.10

Electrical speciﬁcations

Electrical voltage (50 HZ) V 230 400

Maximum current for appliance A 22 25 8.5 9.5 10.5

Nominal current A 11.4 14.2 3.7 4.8 5.5

Maximum current of the Heating system electrical backup A 13.05 / 26.1 3x13

Power of the Heating system electrical backup kW 6 kW (mono) 9 kW (tri)

Circulation pump actual power consumption W 39.5

Maximum power consumed by the outdoor unit W 5060 5750 5865 6555 7245

Rate according to EN14825 0.0049 0.0039 0.0066 0.0053 0.0045

Hydraulic Circuit

Maximum operating pressure

MPa (bar)

0.3 (3)

Flow rate of the hydraulic circuit for 4°C<Δt<8°C

(rated conditions) minimum / maximum l/h 1170 / 2340 1460 / 2920 1170 / 2340 1390 / 2790 1650 / 3290

Miscellaneous

Weight of outdoor unit Kg 92 99

Noise level at 1 m 1(hydraulic unit) dB (A) 39

Sound power level in accordance with EN 12102 2(hydraulic unit) dB (A) 46

Noise level at 5 m 1(outdoor unit) dB (A) 47 47 46 47 47

Sound power level in accordance with EN 12102 2(outdoor unit) dB (A) 69 69 68 69 69

Weight of hydraulic unit (empty / full of water) Kg 42 / 58

Hydraulic unit water capacity l 16

Heating system operating limits

Outdoor temperature min/max °C -25 / +35

Max. heating water ﬂow temperature underﬂoor heating °C 45

Max. heating water ﬂow temperature low temperature radiator °C 60

Min. ﬂow water temperature °C 8

Refrigeration circuit

Gas pipe diameters Inches 5/8

Liquid Piping Diameters Inches 3/8

Factory ﬁll of refrigerant R410A 3g 2500

Maximum operating pressure

MPa (bar)

4.15 (41.5)

Minimum / Maximum length of pipes 4 / 6 m 5 / 15

Maximum length of pipes 5/Maximum level diﬀerence 5m 20 / 15

►

General characteristics

1Sound pressure level at (x) m from the appliance, 1.5m off the ground, open ﬁeld

directionality 2.

2The sound power level is a laboratory measurement of the emitted sound power. It

does not correspond to a measurement of the perceived sound power.

3Refrigerant R410A as per NF EN 378.1 standard.

4Filling with refrigerant R410A is done at the factory.

5Taking into account a possible additional ﬁll of refrigerant R410A (see "Additional

ﬁlling", page 28).

6 The announced thermal and acoustic performances are measured with 7,5m

length refrigerant lines.

alfea excellia A.I. / Installation / 1876 - EN

- 8 -

ﬁg. 1 - Dimensions in mm

31 77900330 12

400

650

Air

Orifice d’écoulement (Ø 20) 4 trous Ø 12

Vue de dessus

Vue de face

Vue de dessous

Vue de coté

1290

151

170

196

370

3/8”

5/8”

Air

900

1290

650

370

Air

31 12330

400

Air

Front view

Top view

Side view

alfea excellia A.I. / Installation / 1876 - EN

■Outdoor Unit,

Excellia A.I. 11 and 14

■Outdoor Unit,

Excellia A.I. tri 11, 14 and 16

4 holesOverﬂow hole

Bottom view

- 9 -

448

9896 477

847

804

Heating return

ø M 26x34

Heating ﬂow

ø M 26x34

Front view Side view

■Hydraulic unit

Space requirements of the hydraulic unit, see page 20.

ﬁg. 2 - Dimensions in mm

1* 2*

1 Elbow

for condensate evacuation.

Plugs (x2)

(depending on

model)

ﬁg. 3 - Accessories provided with the outdoor unit

 6

5 Bracket for attaching hydraulic

unit.

6 Outside sensor to monitor the outdoor

temp.

ﬁg. 4 - Accessories provided with the hydraulic unit

alfea excellia A.I. / Installation / 1876 - EN

- 10 -

-50

1000

10000

43907

2490

338

-25 0 25 50 75

°C

2500

5000

7500

10000

12500

15000

17500

20000

22500

25000

27500

30000

32500

0 10203040 5060 708090100

Outside sensor QAC34

HP return sensor.

HP ﬂow sensor.

ﬁg. 5 - Ohmic sensor values (Hydraulic unit)

ﬁg. 6 - Available hydraulic pressures and ﬂow rates

Variable pressure

Constant speed

Constant pressure

0.2 0.4 0.6 0.8 1 1.2 1.4 1.6

m3/h

mCE (1 mbar = 10 mmCE = 100 Pa)

0 0,5 1 1,5 2 2,5

III

0.2 0.4 0.6 0.8 1 1.2 1.4 1.6

m3/h

mCE (1 mbar = 10 mmCE = 100 Pa)

III

0.2 0.4 0.6 0.8 1 1.2 1.4 1.6

m3/h

mCE (1 mbar = 10 mmCE = 100 Pa)

0 0,5 1 1,5 2 2,5

III

alfea excellia A.I. / Installation / 1876 - EN

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Atlantic Wärmepumpe Handbücher

Atlantic

Atlantic WOYG LCT Series Technisches Handbuch

Atlantic

Atlantic alfea S14 excellia 3-phase Bedienungsanleitung

Atlantic

Atlantic AOYA 30 LBTL Installations- und Betriebshandbuch

Atlantic

Atlantic Loria 6000 R32 Bedienungsanleitung

Atlantic

Atlantic Loria duo 6000 Series Bedienungsanleitung

Atlantic

Atlantic Loria 6000 R32 Bedienungsanleitung

Atlantic

Atlantic Loria 6000 Series Bedienungsanleitung

Atlantic

Atlantic alfea hybrid duo gas Installations- und Betriebshandbuch

Atlantic

Atlantic Alfea Extensa A.I. R32 Bedienungsanleitung

Atlantic

Atlantic Alfea Evolution 5 Bedienungsanleitung

Atlantic

Atlantic Aurea M Series Bedienungsanleitung

Atlantic

Atlantic Alfea Series Bedienungsanleitung

Atlantic

Atlantic Alfea Extensa Duo A.I. 5 R32 Bedienungsanleitung

Atlantic

Atlantic ALFEA Excellia mono Series Bedienungsanleitung

Atlantic

Atlantic Alfea hybrid duo gas Series Installations- und Betriebshandbuch

Atlantic

Atlantic WOYA060LFCA Installations- und Betriebshandbuch

Atlantic

Atlantic Alfea Extensa Duo A.I. 5 Bedienungsanleitung

Atlantic

Atlantic 024122 Installations- und Betriebshandbuch

Atlantic

Atlantic EGEO Bedienungsanleitung

Atlantic

Atlantic Alfea Extensa Duo + 10 Bedienungsanleitung

Atlantic

Atlantic WOYG112LCT Installations- und Betriebshandbuch

Atlantic

Atlantic WOYG112LCT Bedienungsanleitung

Atlantic

Atlantic WOYG112LHT Bedienungsanleitung

Atlantic

Atlantic alfea extensa Series Bedienungsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung