Atlantic WOYA060LFCA Installations- und Betriebshandbuch

Installation

and commissioning

instructions

for professionals

to be kept by the user

for future reference

U0611747_1818_EN_5

18/07/2018

Alféa Extensa A.I.

atlantic-comfort.com

FR NL DE EN IT

ES PT PL PT PT

Air/water heat pump

split 1 service

Outdoor unit Hydraulic unit

WOYA060LFCA 024119

WOYA080LFCA 024120

WOYA100LFTA

"Installation

and maintenance regulations

The appliance must be installed and maintained by

an approved professional in accordance with current

regulations and codes of practice.

"Handling

The outdoor unit must not be placed in a horizontal

position during transport.

If not kept upright during transport, the appliance could

be damaged through displacement of the refrigerant

and damage to the compressor suspension.

Any damage caused by transportation in a horizontal

position is not covered by the warranty.

If necessary, the outdoor unit may be tilted only during

manual handling (to go through a door or up a staircase).

This operation must be conducted very carefully and the

appliance must be immediately restored to the upright

position.

"Containment of refrigeration circuits

All refrigeration circuits are sensitive to contamination

from dust and moisture. If such pollutants penetrate the

refrigeration circuit, they can affect the reliability of the

heat pump.

"Make sure that the connections and refrigeration

circuits (hydraulic unit, outdoor unit) are

protected correctly.

"In the event of a subsequent failure and following

an inspection, the presence of moisture or

foreign bodies in the compressor oil would

automatically void the warranty.

- Check upon receipt that the ttings and refrigeration

circuit caps mounted on hydraulic unit and outdoor unit

are properly seated and secured (cannot be loosened

with bare hands). If this is not the case, tighten them

using a C spanner.

- Check also that the refrigeration connections are

sealed (plastic caps or tubes crimped at the ends

and brazed). If the caps must be removed during the

installation (tubes to be re-cut for example), put them

back as soon as possible.

"Hydraulic connections

The connection must comply with industry standard

practice according to current regulations.

Remember: Seal everything when tting in accordance

with industry standard practice for plumbing work:

- Use suitable seals (bre gasket, O-ring).

- Use Teon or hemp tape.

- Use sealing paste (synthetic depending on the case).

Use glycol/water mix if the minimum ow temperature

is set below 10°C. If you are using a glycol/water

mix, arrange for an annual check on the quality

of the glycol. Use monopropylene glycol only.

The recommended concentration is 30% minimum.

Never use monoethylene glycol.

Remember: The presence at installation of a

CB-type disconnection function, for preventing heating

water being returned to the drinking water system, is

required by articles 16.7 and 16.8 of the Local Plumbing

Regulations.

"In some installations, the presence of different

metals can cause corrosion problems; the

formation of metal particles and sludge can

appear in the hydraulic circuit.

"In this case, it is advisable to use a corrosion

inhibitor in the proportions indicated by the

manufacturer.

- Please refer to the chapter "Treatment of domestic

and heating water" in our price catalogue.

"You must also ensure that treated water does

not become corrosive.

Installation manual "1818- EN"

Alféa Extensa A.I. Heat Pump

- 2 -

• General remarks on electrical connections

It is essential to maintain neutral-phase polarity when

making electrical connections.

Rigid wires are preferable for xed installations,

particularly in a building.

Tighten the cables using the cable glands to prevent the

feed wires from being accidentally disconnected.

The earth connection and its continuity must be ensured.

• Connecting to screw terminals

"The use of ring, spade or blade terminals or

caps is prohibited.

- Always select wire that complies with current standards.

- Bare the end of the wire to around 25 mm.

- With round end pliers, form a loop with a diameter

which matches the tightening screws on the terminal.

- Tighten the terminal screw rmly onto the loop created.

Insufcient tightening can cause overheating, leading

to breakdown or even re.

Rigid wire Loop

25 mm Spade

or blade

terminal

on exible

wire

is prohibited

Screw and special

washer

Terminal

• Connecting to controller boards

- Remove the corresponding connector and make the

connection.

Pre-cabled bundle connector and/or screw connector

• Connecting to spring terminals

- Bare the end of the wire to around 10 mm.

- Push the spring with a screwdriver so that the wire

enters the cage.

- Slide the wire into the opening provided for this purpose.

- Remove the screwdriver and then check that the wire

stays gripped by the cage by pulling on it.

"Electrical connections

• Before any maintenance operation, ensure that

the general power supply is switched off.

• Specications of electricity supply

The electrical installation must be carried out in

accordance with current regulations.

Electrical connections will only be made once all other

installation operations (fastening, assembly, etc.) have

been completed.

"Warning!

The contract signed with the energy provider must

be sufcient not only to cover the heat pump's power

requirements but also the combined sum of all the

appliances likely to be operating at the same time. If the

power is too low, check the power rating stated in your

contract with your energy provider.

Never use a power socket for the power supply.

The heat pump must be supplied directly with power

(without external switch) by special protected leads

from the electric panel via dedicated bipolar circuit

breakers, C curve for the outdoor unit, C curve for

the electrical heating and domestic water backups

(see tables page 39).

The electrical installation must be tted with a 30mA

RCD.

This appliance is designed to operate using a nominal

voltage of 230 V +/- 10%, 50 Hz.

Installation manual "1818- EN" - 3 -

Alféa Extensa A.I. Heat Pump

Contents

Packing . . . . . . . . . . . . . . . . . . . . . . . .6

Unpacking and supplies . . . . . . . . . . . . . . . . 6

Denitions . . . . . . . . . . . . . . . . . . . . . . . 6

General characteristics . . . . . . . . . . . . . . . .7

Description. . . . . . . . . . . . . . . . . . . . . . 14

Operating principle . . . . . . . . . . . . . . . . . 16

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Installation of refrigeration connections . . . . . . . 18 Installation of the outdoor unit . . . . . . . . . . . . 20

Installation of the hydraulic unit . . . . . . . . . . . 22

Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Cable dimensions and protection rating . . . . . . . 39

Electrical connections on the outdoor unit side . . . 40

Electrical connections on the hydraulic unit side . . 42

Outdoor sensor . . . . . . . . . . . . . . . . . . . 44

Room sensor (option) . . . . . . . . . . . . . . . . 44

Controller Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

User Interface . . . . . . . . . . . . . . . . . . . . 48

Display Description . . . . . . . . . . . . . . . . . 49

Installer Menu . . . . . . . . . . . . . . . . . . . . 50

Navigating the Menus . . . . . . . . . . . . . . . . 50

Modifying Settings . . . . . . . . . . . . . . . . . . 51

Temperature control . . . . . . . . . . . . . . . . . 52

This appliance must be installed by qualied personnel holding a certicate of competence in the handling

of refrigerants.

Description of the equipment . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Refrigeration connections and lling the installation with gas . . . . . . . 24

Rules and precautions. . . . . . . . . . . . . . . . 24

Shaping the refrigeration pipes . . . . . . . . . . . 24

Checks and connection . . . . . . . . . . . . . . . 27

Filling the installation with gas. . . . . . . . . . . . 28

Hydraulic connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Connecting the hydraulic unit to the heating circuit . 34

Filling and bleeding the installation . . . . . . . . . 35

Heating circulation pump speed settings . . . . . . 36

Commissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Installation manual "1818- EN"

Alféa Extensa A.I. Heat Pump

- 4 -

Basic Hydraulic Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Electrical Cabling Plans . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Fault Diagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Faults in the hydraulic unit. . . . . . . . . . . . . . 80 Faults in the outdoor unit . . . . . . . . . . . . . . 81

Maintenance of the installation . . . . . . . . . . . . . . . . . . . . . . . . 82

Checking the hydraulic circuit . . . . . . . . . . . . 82

Checking the outdoor unit . . . . . . . . . . . . . . 82

Checking the electrical circuit . . . . . . . . . . . . 82

Other maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Emptying the hydraulic unit . . . . . . . . . . . . . 83 Distribution valve . . . . . . . . . . . . . . . . . . 83

Quick-start procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Start-up check-list . . . . . . . . . . . . . . . . . . 84 Commissioning technical datasheet. . . . . . . . . 86

ErP performance gures. . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Controller Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Menu Structure . . . . . . . . . . . . . . . . . . . 54

Installed options . . . . . . . . . . . . . . . . . . . 55

Hydraulic conguration . . . . . . . . . . . . . . . 55

Heat Pump Conguration . . . . . . . . . . . . . . 60

System status . . . . . . . . . . . . . . . . . . . . 62

Auxiliary functions . . . . . . . . . . . . . . . . . . 64

Settings . . . . . . . . . . . . . . . . . . . . . . . 66

Easy Start . . . . . . . . . . . . . . . . . . . . . . 70

Denition of ErP . . . . . . . . . . . . . . . . . . . 88

ErP specication. . . . . . . . . . . . . . . . . . . 88

Package datasheet . . . . . . . . . . . . . . . . . 90

Instructions for the end user . . . . . . . . . . . . . . . . . . . . . . . . . 91

Installation manual "1818- EN" - 5 -

Alféa Extensa A.I. Heat Pump

1.1 Packing

• 1 package: Outdoor unit.

• 1 package: Hydraulic unit and outdoor temperature

sensor.

1.2 Unpacking and supplies

While the courier is still present, carefully check the

general appearance of the appliances and check

that the outdoor unit has not been laid in a horizontal

position.

In the event of a dispute, send any relevant reservations

to the carrier in writing within 48 hours and send a copy

of the letter to Customer Services.

1.3 Denitions

- Split: The heat pump consists of two elements

(an outdoor unit to be installed outdoors and a hydraulic

unit to be installed inside the dwelling).

- Air/water: The surrounding air is the energy source.

This energy is transmitted to the heating circuit water

by the heat pump.

- Inverter: The fan and compressor speeds are

modulated according to the heating requirements.

This technology enables you to save on energy and

operate on a single-phase power supply, whatever

the heat pump's output, by avoiding pulling signicant

amounts of current at start-up.

- COP (Coefcient of Performance): This is the

relationship between the energy transmitted to the

heating circuit and consumed electrical energy.

1 Description of the equipment

Installation manual "1818- EN"

Alféa Extensa A.I. Heat Pump

- 6 -

Packing contents list

Heat Pump Outdoor unit Hydraulic unit

Model Export

code Reference Code Reference Code

Alféa Extensa A.I. 5 526220 WOYA060LFCA 700171 Alféa Extensa A.I. 5 024119

Alféa Extensa A.I. 6 526221

Alféa Extensa A.I. 6-10 024120

Alféa Extensa A.I. 8 526222 WOYA080LFCA 700172

Alféa Extensa A.I. 10 526223 WOYA100LFTA 700173

Optional equipment

• Dual circuit kit (code 074025)

for connecting 2 heating circuits.

• 6 kW backup relay kit (code 075327)

for switching to HP electrical backup of 3 to 6 kW.

• DHW kit (code 073991)

for connecting a mixed DHW tank

(with built-in electrical backups).

• Boiler connection kit (code 073989)

for connecting a boiler to the heat pump.

• Wireless room sensor A59(code 074208) for

correcting the ambient temperature.

• Wireless room sensor A75 (code 074213),

Wireless room sensor A78 (code 074214)

for correcting the ambient temperature and

programming the heat pump.

• Cooling kit (code 075328).

• High ow rate circulation pump kit (code 074077)

for the installation of 1 underoor heating circuit.

• Anti-vibration blocks (code 523574).

• White PVC oor support (ref. 809532) or

Black rubber oor support (ref. 809536).

Operating Range

This heat pump provides:

- Heating in winter,

- The management of electrical backups, for extra

heating on the coldest days,

- Installation with boiler connection* for extra heating on

the coldest days,

- Management of two heating circuits*,

- Production of domestic hot water* (provided that it is

combined with a mixed DHW tank),

- Cooling in summer* (for underoor heating-cooling

system or fan-convectors).

*: These options require the use of additional kits (see chapter

"Required accessory" or "Optional equipment").

1.4 General characteristics

Model name Alféa Extensa A.I. 5 6 8 10

Rated heating performances (outdoor temp. / ow temp.)

Heat output

+7°C/+35°C - Underoor heating system kW 4.50 6.00 7.50 10.00

-7°C/+35°C - Underoor heating system kW 4.10 4.60 5.70 7.40

+7°C/+45°C - LT radiator kW 4.50 5.10 6.20 8.27

-7°C/+45°C - LT radiator kW 4.10 4.45 5.05 7.40

+7°C/+55°C - Radiator kW 4.50 4.50 5.00 7.00

-7°C/+55°C - Radiator kW 3.70 3.85 5.20 7.00

Power consumption

+7°C/+35°C - Underoor heating system kW 1.00 1.41 1.84 2.49

-7°C/+35°C - Underoor heating system kW 1.47 1.74 2.23 2.97

+7°C/+45°C - LT radiator kW 1.31 1.50 1.87 2.53

-7°C/+45°C - LT radiator kW 1.86 2.04 2.47 3.70

+7°C/+55°C - Radiator kW 1.79 1.79 1.94 2.86

-7°C/+55°C - Radiator kW 2.20 2.33 3.34 4.15

Coefcient of Performance (COP) (+7°C/+35°C) 4.52 4.26 4.08 4.02

Electrical specications

Electrical voltage (50 Hz) V 230

Maximum current for appliance A 11 12.5 17.5 18.5

Nominal current A 4.5 6.3 8.1 10.9

Maximum current of the Heating system electrical backup A 13.05 / 26.1

Power of the Heating system electrical backup kW 3 (6 kW option available)

Circulation pump actual power consumption W 24 24 24 24

Maximum power consumed by the outdoor unit W 2530 2875 4025 4255

Rate according to EN14825 0.0100 0.0070 0.0057 0.0044

Hydraulic Circuit

Maximum operating pressure MPa (bar) 0.3 (3)

Flow rate of the hydraulic circuit for 4°C<Δt<8°C (rated conditions)

minimum / maximum l/h 490/980 650/1300 810/1620 1080/2160

Miscellaneous

Weight of outdoor unit Kg 41 41 42 60

Noise level 1at 1 metre (hydraulic unit) dB (A) 39

Sound power level in accordance with EN 12102 2(hydraulic unit) dB (A) 46

Noise level 1at 5 metre (outdoor unit) dB (A) 41 41 47 47

Sound power level in accordance with EN 12102 2(outdoor unit) dB (A) 63 63 69 69

Weight of hydraulic unit (empty / full of water) Kg 46 / 62

Hydraulic unit water capacity l 16

Heating system operating limits

Outdoor temperature min/max °C -20 / +35 -20 / +35 -20 / +35 -20 / +35

Underoor heating system max. heating ow water temperature °C 45

LT radiator max. heating ow water temperature °C 55 55 55 55

Min. ow water temperature °C 8

Refrigeration circuit

Gas pipe diameters Inches 1/2 1/2 5/8 5/8

Liquid Piping Diameters Inches 1/4 1/4 1/4 3/8

Factory ll of refrigerant R410A 3g 1100 1100 1400 1800

Maximum operating pressure MPa (bar) 4.15 (41.5)

Minimum / Maximum length of pipes 4 / 6 m 5 / 15 5 / 15 5 / 15 5 / 15

Maximum length of pipes 5/Maximum level difference m 30 / 20 30 / 20 30 / 20 30 / 20

1Hydraulic unit: Sound pressure level at (x) m from the appliance, 1.5m off the

ground, open eld directionality 2 / Outdoor unit : Sound pressure level at (x) m

from the device, halfway between the ground and top of the outdoor unit, open

eld directionality 2.

The sound power level is a laboratory measurement of the emitted sound

power. It does not correspond to a measurement of the perceived sound

power.

3Refrigerant R410A as per NF EN 378.1 standard.

4Filling with refrigerant R410A is done at the factory.

5 Taking into account a possible additional ll of refrigerant R410A

(see "Additional lling", page 31).

6 The announced thermal and acoustic performances are measured with 7,5m

length refrigerant lines.

Installation manual "1818- EN" - 7 -

Alféa Extensa A.I. Heat Pump

gure 1 - Dimensions in mm

650

AIR

370

830

196

900 77

33031

147

170

400

540

4 holes Ø11

790

290

18 23

209

352

620

320

110

175

AIR

4 holes ø11

Installation manual "1818- EN"

Alféa Extensa A.I. Heat Pump

- 8 -

"Outdoor Unit,

Alféa Extensa A.I. 5, 6 and 8

"Outdoor Unit,

Alféa Extensa A.I. 10



Installation manual "1818- EN" - 9 -

Alféa Extensa A.I. Heat Pump

448

9896 477

842

804

Heating return

ø M 26x34

Heating ow

ø M 26x34

Front view Side view

"Hydraulic unit

gure 4 - Dimensions in mm

Space requirements of the hydraulic unit, see page 22

5 6 7

5 Bracket for attaching hydraulic

unit.

6Outdoor sensor to monitor the outdoor

temp.

7* Adapter 1/2" - 5/8" and/

or 1/4" - 3/8" for are connection to

hydraulic unit.

8* Nut 1/2" and/or 1/4"

* only for Alféa Extensa A.I. 5, 6 and 8.

gure 3 - Accessories provided

with the hydraulic unit

gure 2 - Accessories provided

with the outdoor unit

1* Elbow

for condensate evacuation

Plugs (x2)

(depending on

model)

* only for Alféa Extensa A.I. 10.

1* 2*

3**

Installation manual "1818- EN"

Alféa Extensa A.I. Heat Pump

- 10 -

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Atlantic Wärmepumpe Handbücher

Atlantic

Atlantic alfea excellia duo 11 Installations- und Betriebshandbuch

Atlantic

Atlantic Alfea Hybrid Duo Series Installations- und Betriebshandbuch

Atlantic

Atlantic EGEO Bedienungsanleitung

Atlantic

Atlantic WOYG112LHT Bedienungsanleitung

Atlantic

Atlantic Loria Duo 6000 R32 Bedienungsanleitung

Atlantic

Atlantic alfea S S5 Bedienungsanleitung

Atlantic

Atlantic 023159 Bedienungsanleitung

Atlantic

Atlantic Alfea Extensa A.I. R32 WOYA060KLT Bedienungsanleitung

Atlantic

Atlantic Loria 6000 Series Bedienungsanleitung

Atlantic

Atlantic alfea extensa duo+ Bedienungsanleitung

Atlantic

Atlantic AOYA 18 LALL Bedienungsanleitung

Atlantic

Atlantic Alfea Excellia HP Duo A.I. Series Bedienungsanleitung

Atlantic

Atlantic Alfea Evolution 5 Bedienungsanleitung

Atlantic

Atlantic Alfea Series Bedienungsanleitung

Atlantic

Atlantic WOYA 060 LDC Bedienungsanleitung

Atlantic

Atlantic WOYG160LJL Bedienungsanleitung

Atlantic

Atlantic Loria 6000 R32 Bedienungsanleitung

Atlantic

Atlantic Geolia 5 Bedienungsanleitung

Atlantic

Atlantic Alfea Extensa A.I. R32 Bedienungsanleitung

Atlantic

Atlantic Geolia 13 Bedienungsanleitung

Atlantic

Atlantic 024122 Installations- und Betriebshandbuch

Atlantic

Atlantic CALYPSO VM Bedienungsanleitung

Atlantic

Atlantic 024306 Bedienungsanleitung

Atlantic

Atlantic Alfea Extensa Duo A.I. 5 R32 Bedienungsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung