Atlona AT-HD-V40SRS Bedienungsanleitung

AtlonA

HDMI 1.3 over Single CAT5 Extender

AT-HD-V40SRS

User Manual

TABLE OF CONTENTS

1. Introduction .................................................. 1

2. Features .................................................. 1

3. Specication .................................................. 2

4. Package Contents .................................................. 3

5. Connection Diagram .................................................. 3

6. Panel Descriptions .................................................. 4

6.1. AT-HD-V40SS .................................................. 4

6.2. AT-HD-V40RS .................................................. 5

7. Hardware Installation .................................................. 6

8. EDID Learning .................................................. 6

9. Notice .................................................. 7

10. Safety Information .................................................. 8

11. Warranty .................................................. 9

12. Atlona Product Registration .................................................. 10

INTRODUCTION

Atlona’s AT-HD-V40SRS HDMI 1.3 over Single CAT5 Extender boosts up your video/audio transmission

distance up to 60m (200ft) in HDTV 1080i format, 40m (130ft) in HDTV 1080p format, and 20m (65ft) in

HDTV 1080p with 36 bit color depth. With only one cost effective LAN cable, users can readily extend

HDTV sources from DVD players, Blu-ray Disc player, PS3, PC, and any other kinds of sources compli-

ant with TMDS to distant display monitors including HDMI/DVI enabled TV sets or LCD PC monitors.

With the state-of-the-art Silicon Image chipsets equipped, deep color video, DTS-HD or Dolby TrueHD

audio, and HDCP supports and compatibility are all further insured. This exibility makes HDCP com-

pliant DVD players or PS3 transmit utmost high quality video and audio with a greater distance at the

minimal cost, when integrating several components apart.

The AT-HD-V40SRS includes two units: Sender (AT-HD-V40SS) and Receiver (AT-HD-V40RS) units.

The Sender unit is used to capture the input HDMI/DVI signals and carry the signals through one RJ-45

connector into one cost effective CAT-5/5e/6 LAN cable. The Receiver unit is responsible for equaliz-

ing the sent TMDS multimedia data. The transmission distance between the sender and receiver units

can be up to 60m (200ft) under HD (720p/1080i) or 40m (130ft) under Full HD (1080p). With an 8-level

equalization control knob on the receiving unit, users can adjust the equalization strength to the re-

ceived TMDS signals accordingly, and therefore optimize the transmission distance between source and

destination.

• State-of-the-art Silicon Image (founder of HDMI) chipset embedded for upmost compatibility and reli-

ability

• HDMI 1.3c compliant

• Extend the transmission length up to 60m (200ft) from the HDMI sources under HD resolution (1080i

or 720p at 24-bit color depth)

• Extend the transmission length up to 40m (130ft) from the HDMI sources under Full HD resolution

(1080p at 24-bit color depth)

• Extend the transmission length up to 20m (65ft) from the HDMI sources under Full HD resolution

(1080p at 36-bit color depth)

• HDCP 1.1 compliant

• Minimize the cable skew by adjustable 8-level equalization control

• Pure unaltered uncompressed 7.1ch digital HDMI over LAN cable transmission

• DTS-HD and Dolby True HD high bit rate audio support

• Allows cascading

• Wall mounting housing design for easy installation

• Perfectly integrated with other HDMI over CAT5 series products

Note: The length depends on the characteristics and quality of the cables. Higher resolutions and longer trans-

mission distances require low skew cables (<25ns/100m) for best performance. Unshielded CAT6 with metal

RJ-45 connectors is recommended.

FEATURES:

SPECIFICATIONS

Technical AT-HD-V40SS AT-HD-V40RS

Role of usage Sender Receiver

HDMI compliance HDMI 1.3c

HDCP compliance Yes

Video bandwidth Single-link 225MHz [6.75Gbps]

Video support 480i / 480p / 720p / 1080i / 1080p60

HDMI transmission over

LAN cable [24-bit]

Full HD (1080p)-40m (130ft) [CAT5e] / 50m (165ft) [CAT6]

HD (720p/1080i)-50m (165ft) [CAT5e] / 60m (200ft) [CAT6]

Audio support Surround sound (up to 7.1ch) or stereo digital audio

Equalization 8-level digital control at RX

Input TMDS signal 1.2 Volts [peak-to-peak]

Input DDC signal 5 Volts [peak-to-peak, TTL]

ESD protection [1] Human body model — ±15kV [air-gap discharge] & ±8kV [contact

discharge]

[2] Core chipset — ±8kV

PCB stack-up 4-layer board [impedance control — differential 100 ; single 50 ]

Input 1x HDMI 1x RJ-45

Output 1x RJ-45 1x HDMI

HDMI source control No

IR remote control N/A

HDMI connector Type A [19-pin female]

RJ-45 connector WE/SS 8P8C with 2 LED indicator

3.5mm connector None

Rotary control switch Mode Signal level

Mechanical

Housing Metal case

Dimensions

[L x W x H]

Model

[Sender/

Receiver]

93 x 60 x 25mm [3.7”x2.4”x1”]

Package 270 x 175 x 80mm [10.6” x 6.9” x 3.1”]

Carton 450 x 370 x 300mm (1’6” x 1’3” x 11.8”]

Weight Model 405g [14.2oz]

Package 815g [1.8 lbs]

Fixedness Wall-mounting case with screws

Power supply 5V 2A DC

Power consumption 1 Watt [max]

Operation temperature 0~40oC [32~104oF]

Storage temperature -20~60oC [-4~140oF]

Relative humidity 20~90% RH [no condensation]

2 3

1. 1xAT-HD-V40SRS [Sender/Receiver]

2. 1x 5V power adapter

3. 1x User Manual

PACKAGE CONTENTS:

CONNECTION DIAGRAM

HDMI Display

HDMI Projector/Display DVI Projector/Display

HDMI Source

AT-HD-V40SS

AT-HD15SRS AT-DVI15SRS

AT-HD-V40RS

HDMI Cable

Single CAT 5e

AT-HD-V40SS

Front Panel

HDMI IN: Connects to an HDMI source with an HDMI Male-Male cable here

MODE: 0 = [Video] – supports up to HDMI 1.3 output. [Audio] – supports up to 7.1ch output

1 = [Video] – supports up to HDMI 1.3 output. [Audio] – locks to stereo audio output

2 = [Video] – locks to HDMI 1.2 output. [Audio] – supports up to 7.1ch output

3 = [Video] – locks to HDMI 1.2 output. [Audio] – locks to stereo audio output

4 = [Video] – DVI display mode. [Audio] – no audio output

5 = [Safe Mode] – uses default EDID1 with video supported up to 720p/1080i

6 = [Default Mode] – uses default EDID2 with video supported up to 1080p

7 = [EDID Learning Mode] – learns EDID3 from the display

Note for EDID (Extended Display Identication Data) learning

1.If you cannot get the audio/video output from the connected display from the rst time setup. Please follow the instructions below to check if

the extender is OK:

Step 1 – Please set the rotary arrow on Sender at “Mode 5” for Safe Mode, and wait for the LED of the RJ-45 connector blinks for a couple

seconds.

Step 2 – Please turn the rotary arrow counterclockwise from Mode 5 to Mode 3. If you can get audio/video from the display, you can stay

tune at this setting for 720p or 1080i and stereo audio. If you need to get 720p/1080i with 7.1ch audio output, please turn the rotary arrow

counterclockwise from Mode 3 to Mode 2. For better audio/video output, please check Note#2. If you still cannot get the audio/video out

normally, please go on the next step.

Step 3 – Please turn the rotary arrow counterclockwise from Mode 3 to Mode 7. Wait a few seconds until the LED of the RJ-45 connector

dims and then lights again.

Step 4 – Please turn the rotary arrow clockwise from Mode 7 to Mode 1. You should have normal audio/video output. If not, please contact

technical support.

2.For desirable 1080p video output, please follow the instructions below:

Step 1 – Please set the rotary arrow on Sender at “Mode 6” for Default Mode, and wait for the LED of the RJ-45 connector blinks for a couple

seconds.

Step 2 – Please turn the rotary arrow clockwise from Mode 6 to Mode 1. If you can get audio/video from the display, you can stay tune at

this setting for 1080p and stereo audio. If you need to get 1080p with 7.1ch audio output, please turn the rotary arrow counterclockwise from

Mode 1 to Mode 0. If you cannot get the audio/video out normally, please go on the next step.

Step 3 – Please turn the rotary arrow counterclockwise from Mode 0/1 to Mode 7. Wait a few seconds until the LED of the RJ-45 connec-

tor dims and then lights again.

Step 4 – Please turn the rotary arrow clockwise from Mode 7 to Mode 0/1. You should have your desirable audio/video output. If not,

please follow the instruction in Note#1.

3.To learn EDID from the HDMI display, please follow the instruction below:

Step 1 – Please connect the display which you want to read EDID with a HDMI cable to the transmitter’s HDMI IN and set the rotary arrow at

Mode 7 so the Sender can learn the EDID information from the connected display. The LED on the RJ45 connector of Sender will dim and light

again in a few seconds, which indicates the EDID learning procedure is complete.

Step 2 – Please turn the rotary arrow clockwise from Mode 7 to Mode 0 or Mode 1 for desirable audio setting and enjoy the experience.

DO NOT let the rotary arrow pass by Mode 5 and Mode 6 which will erase the EDID just learned and restore the default EDID.

PANEL DESCRIPTIONS

4 5

Rear Panel

+5V DC: Connect to 5V DC power supply.

HDMI Signal OUT: Plug in a CAT-5/5e/6 LAN cable that needs to be linked to the RJ-45 connector of the receiver unit

AT-HD-V40RS.

AT-HD-V40RS

Front Panel

HDMI OUT: Connect to a HDMI display with a HDMI Male-Male cable here.

Signal Level: Adjust the 8-level equalization rotary control switch to the received HDMI signals. 0 – 7 = strongest – weakest. It

is recommended to switch from 7 to 0 to nd the optimal visual experience.

Rear Panel

HDMI Signal IN: Plug in a CAT-5/5e/6 cable that needs to be linked to the RJ-45 connector of the Sender unit AT-HD-V40SS.

+5V DC: Connect to 5V DC power supply.

1.Connect the HDMI/DVI source (such as a Blu-ray Disc player) to the Sender unit AT-HD-

V40SS.

2.Connect the HDMI/DVI display (such as a LCD TV) to the Receiver unit AT-HD-V40RS.

3.Connect a CAT-5/5e/6 LAN cable between the transmitting and receiving units.

4.Make sure this CAT-5/5e/6 LAN cable is tightly connected and not loose.

5.Plug in 5V DC power cord to the power jack of the receiving unit AT-HD-V40RS.

6.Plug in 5V DC power cord to the power jack of the transmitting unit AT-HD-V40SS.

7. If a ickering or a blinking image is seen, try to adjust the rotational switch to improve the

cable skew. 0 stands for the strongest HDMI signal level while 7 stands for the weakest. Try

adjusting the signal level from 7 to 0 to accommodate the length of HDMI over CAT5 trans-

mission.

1.Turn on AT-HD-V40SS.

2.Turn the Mode of AT-HD-V40SS to 7.

3.Connect the HDMI display to the “HDMI IN” of AT-HD-V40SS with a HDMI cable. The LED

on the RJ-45 connector of AT-HD-V40SS will dim and light again, which indicates the EDID

learning procedure is complete.

4.Turn the Mode of AT-HD-V40SS clockwise from 7 to 0 (for surround sound) or 1 (for ste-

reo). The most important thing is don’t let the rotary arrow pass through mode 5 and Mode 6

which will erase the EDID just learned and restore to default EDID.

5.Unplug the HDMI cable from the display and follow the instruction in [Hardware Installation]

to set up the AT-HD-V40SRS and enjoy the experience.

HARDWARE INSTALLATION:

EDID LEARNING

NOTICE

1.If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to

retrieve and provide DVI/HDMI EDID information.

2.All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e

125MHz LAN cable and ASTRODESIGN Video Signal Generator VG-859C.

3.The transmission length is largely affected by the type of LAN cables, the type of HDMI

sources, and the type of HDMI display. The testing result shows solid LAN cables (usu-

ally in bulk cable 300m or 1000ft form) can transmit a lot longer signals than stranded LAN

cables (usually in patch cord form). Shielded STP cables are better suit than unshielded UTP

cables. A solid UTP CAT5e cable shows longer transmission length than stranded STP CAT6

cable. For long extension users, solid LAN cables are your only choice.

4.EIA/TIA-568-B termination (T568B) for LAN cables is recommended for better performance.

5.To reduce the interference among the unshielded twisted pairs of wires in LAN cable, you

can use shielded LAN cables to improve EMI problems, which is worsen in long transmis-

sion.

6.Because the quality of the LAN cables has the major effects in how long transmission dis-

tance will be made and how good is the received display, the actual transmission length is

subject to your LAN cables. For resolution greater than 1080i or 1280x1024, a CAT6 cable is

recommended.

7. If your HDMI display has multiple HDMI inputs, it is found that the rst HDMI input [HDMI

input #1] generally can produce better transmission performance among all HDMI inputs.

Performance Guide for HDMI over LAN Cable Transmission

Performance rating Type of LAN cable

Wiring Shielding CAT5 CAT5e CAT6

Solid Unshielded (UTP) *** **** *****

Shielded (STP) *** *** ****

Stranded Unshielded (UTP) * ** **

Shielded (STP) * * **

Termination Please use EIA/TIA-568-B termination (T568B) at any time

SAFETY INFORMATION

Safeguards

To reduce the risk of electric shock, do not

expose this product to rain or moisture.

If the wall plug does not t into your local

power socket, hire an electrician to replace

your obsolete socket.

Do not modify the wall plug.

Doing so will void the warranty and safety

features.

This equipment should be installed near

the socket outlet and the device should

be easily accessible in case it requires

disconnection.

Precautions

FCC Regulations state that any

unauthorized changes or modications to

this equipment not expressly approved by

the manufacturer could void the

user’s authority to operate this

equipment.

Operate this product using only the

included external power supply. Use of

other power supplies could impair

performance, damage the product or cause

res.

In the event of an electrostatic discharge,

this device may automatically turn off. If this

occurs, unplug the device, and plug it back

in.

Protect and route power cords so they will

not be stepped on or pinched by anything

placed on or against them. Be especially

careful of plug-ins, or cord exit points from

this product.

Avoid excessive humidity, sudden

temperature changes or temperature

extremes.

Keep this product away from wet locations

such as bathtubs, sinks, laundries, wet

basements and swimming pools.

Use only accessories recommended by

ATLONA to avoid re, shock or other

hazards.

Unplug the product before cleaning. Use

a damp cloth for cleaning. Do not use

cleaning uid or aerosols, which could

enter the unit and cause damage, re or

electrical shock. Some substances may

also mar the nish of the product.

Never open or remove unit panels or make

any adjustments not described in this

manual. Attempting to do so could expose

you to dangerous electrical shock or other

hazards. It may also cause damage to your

AT-HD-V40SRS. Opening the product will

void the warranty.

Do not attempt to service the unit. Instead

disconnect it and contact your Authorized

ATLONA reseller or contact ATLONA

directly.

Andere Handbücher für AT-HD-V40SRS

Inhaltsverzeichnis

Andere Atlona Extender Handbücher

Atlona

Atlona AT-HD4-SI40SR Bedienungsanleitung

Atlona

Atlona AT-RGB45SR Bedienungsanleitung

Atlona

Atlona AT-DVI15SRS Bedienungsanleitung

Atlona

Atlona AT-COMP300SL Bedienungsanleitung

Atlona

Atlona AT-VGA180AR Bedienungsanleitung

Atlona

Atlona AT-HD4-V40SRS Bedienungsanleitung

Atlona

Atlona AT-VGA180AS Bedienungsanleitung

Atlona

Atlona AT-HD-IR40SR Bedienungsanleitung

Atlona

Atlona AT-VBNC400SR Bedienungsanleitung

Atlona

Atlona AT-VGA-RS300SRS Bedienungsanleitung

Atlona

Atlona AT-UHD-EX-70-KIT Bedienungsanleitung

Atlona

Atlona AT-DVITX-RSNET Bedienungsanleitung

Atlona

Atlona AT-DVIF20SR Bedienungsanleitung

Atlona

Atlona AT-VGA100-SR Bedienungsanleitung

Atlona

Atlona AT-VGA-RS300SRS Bedienungsanleitung

Atlona

Atlona AT-IR300SRS Bedienungsanleitung

Atlona

Atlona AT-HDTX Bedienungsanleitung

Atlona

Atlona AT-2VGA300SL Bedienungsanleitung

Atlona

Atlona AT-UHD-EX-70C-KIT Bedienungsanleitung

Atlona

Atlona AT-PRO2HD1616M-RX Bedienungsanleitung

Atlona

Atlona AT-DVIDF40SR Bedienungsanleitung

Atlona

Atlona AT-HD4-SI40SR Bedienungsanleitung

Atlona

Atlona AT-UHD-EX-70-2PS Series Bedienungsanleitung

Atlona

Atlona AT-80120HD Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung