Atmel AT90S1200 Bedienungsanleitung

Features

•Utilizes the AVR®RISC Architecture

•AVR –High-performance and Low-power RISC Architecture

–89 Powerful Instructions –Most Single Clock Cycle Execution

–32 x 8 General Purpose Working Registers

–Up to 12 MIPS Throughput at 12 MHz

•Data and Non-volatile Program Memory

–1K Byte of In-System Programmable Flash

Endurance: 1,000 Write/Erase Cycles

–64 Bytes of In-System Programmable EEPROM

Endurance: 100,000 Write/Erase Cycles

–Programming Lock for Flash Program and EEPROM Data Security

•Peripheral Features

–One 8-bit Timer/Counter with Separate Prescaler

–On-chip Analog Comparator

–Programmable Watchdog Timer with On-chip Oscillator

–SPI Serial Interface for In-System Programming

•Special Microcontroller Features

–Low-power Idle and Power-down Modes

–External and Internal Interrupt Sources

–Selectable On-chip RC Oscillator for Zero External Components

•Specifications

–Low-power, High-speed CMOS Process Technology

–Fully Static Operation

•Power Consumption at 4 MHz, 3V, 25°C

–Active: 2.0 mA

–Idle Mode: 0.4 mA

–Power-down Mode: <1 µA

•I/O and Packages

–15 Programmable I/O Lines

–20-pin PDIP, SOIC and SSOP

•Operating Voltages

–2.7 - 6.0V (AT90S1200-4)

–4.0 - 6.0V (AT90S1200-12)

•Speed Grades

–0 - 4 MHz, (AT90S1200-4)

–0 - 12 MHz, (AT90S1200-12)

Pin Configuration

8-bit

Microcontroller

with 1K Byte

of In-System

Programmable

Flash

AT90S1200

Rev. 0838H–AVR–03/02

2AT90S1200

0838H–AVR–03/02

Description The AT90S1200 is a low-power CMOS 8-bit microcontroller based on the AVR RISC

architecture. By executing powerful instructions in a single clock cycle, the AT90S1200

achieves throughputs approaching 1 MIPS per MHz allowing the system designer to

optimize power consumption versus processing speed.

The AVR core combines a rich instruction set with the 32 general purpose working reg-

isters. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU),

allowing two independent registers to be accessed in one single instruction executed in

one clock cycle. The resulting architecture is more code efficient while achieving

throughputs up to ten times faster than conventional CISC microcontrollers.

Block Diagram Figure 1. The AT90S1200 Block Diagram

The architecture supports high-level languages efficiently as well as extremely dense

assembler code programs. The AT90S1200 provides the following features: 1K byte of

In-System Programmable Flash, 64 bytes EEPROM, 15 general purpose I/O lines, 32

general purpose working registers, internal and external interrupts, programmable

watchdog timer with internal oscillator, an SPI serial port for program downloading and

two software selectable power-saving modes. The Idle Mode stops the CPU while allow-

AT90S1200

0838H–AVR–03/02

ing the Registers, Timer/Counter, Watchdog and Interrupt system to continue

functioning. The Power-down mode saves the register contents but freezes the Oscilla-

tor, disabling all other chip functions until the next External Interrupt or hardware Reset.

The device is manufactured using Atmel’s high-density nonvolatile memory technology.

The On-chip In-System Programmable Flash allows the program memory to be repro-

grammed in-system through an SPI serial interface or by a conventional nonvolatile

memory programmer. By combining an enhanced RISC 8-bit CPU with In-System Pro-

grammable Flash on a monolithic chip, the Atmel AT90S1200 is a powerful

microcontroller that provides a highly flexible and cost-effective solution to many embed-

ded control applications.

The AT90S1200 AVR is supported with a full suite of program and system development

tools including: macro assemblers, program debugger/simulators, in-circuit emulators,

and evaluation kits.

Pin Descriptions

VCC Supply voltage pin.

GND Ground pin.

Port B (PB7..PB0) Port B is an 8-bit bi-directional I/O port. Port pins can provide internal pull-up resistors

(selected for each bit). PB0 and PB1 also serve as the positive input (AIN0) and the

negative input (AIN1), respectively, of the On-chip Analog Comparator. The Port B out-

put buffers can sink 20 mA and thus drive LED displays directly. When pins PB0 to PB7

are used as inputs and are externally pulled low, they will source current if the internal

pull-up resistors are activated. The Port B pins are tri-stated when a reset condition

becomes active, even if the clock is not active.

Port B also serves the functions of various special features of the AT90S1200 as listed

on page 30.

Port D (PD6..PD0) Port D has seven bi-directional I/O pins with internal pull-up resistors, PD6..PD0. The

Port D output buffers can sink 20 mA. As inputs, Port D pins that are externally pulled

low will source current if the pull-up resistors are activated. The Port D pins are tri-stated

when a reset condition becomes active, even if the clock is not active.

Port D also serves the functions of various special features of the AT90S1200 as listed

on page 34.

RESET Reset input. A low level on this pin for more than 50 ns will generate a reset, even if the

clock is not running. Shorter pulses are not guaranteed to generate a reset.

XTAL1 Input to the inverting oscillator amplifier and input to the internal clock operating circuit.

XTAL2 Output from the inverting oscillator amplifier.

Crystal Oscillator XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier which can

be configured for use as an On-chip Oscillator, as shown in Figure 2. Either a quartz

crystal or a ceramic resonator may be used. To drive the device from an external clock

source, XTAL2 should be left unconnected while XTAL1 is driven as shown in Figure 3.

4AT90S1200

0838H–AVR–03/02

Figure 2. Oscillator Connections

Note: When using the MCU Oscillator as a clock for an external device, an HC buffer should be

connected as indicated in the figure.

Figure 3. External Clock Drive Configuration

On-chip RC Oscillator An On-chip RC Oscillator running at a fixed frequency of 1 MHz can be selected as the

MCU clock source. If enabled, the AT90S1200 can operate with no external compo-

nents. A control bit (RCEN) in the Flash Memory selects the On-chip RC Oscillator as

the clock source when programmed (“0”). The AT90S1200 is normally shipped with this

bit unprogrammed (“1”). Parts with this bit programmed can be ordered as

AT90S1200A. The RCEN-bit can be changed by parallel programming only. When

using the On-chip RC Oscillator for Serial Program downloading, the RCEN bit must be

programmed in Parallel Programming mode first.

XTAL2

XTAL1

GND

MAX 1 HC BUFFER

AT90S1200

0838H–AVR–03/02

Architectural

Overview

The fast-access register file concept contains 32 x 8-bit general purpose working regis-

ters with a single clock cycle access time. This means that during one single clock cycle,

one ALU (Arithmetic Logic Unit) operation is executed. Two operands are output from

the register file, the operation is executed, and the result is stored back in the register

file –in one clock cycle.

Figure 4. The AT90S1200 AVR RISC Architecture

The ALU supports arithmetic and logic functions between registers or between a con-

stant and a register. Single register operations are also executed in the ALU. Figure 4

shows the AT90S1200 AVR RISC microcontroller architecture. The AVR uses a Har-

vard architecture concept –with separate memories and buses for program and data

memories. The program memory is accessed with a 2-stage pipeline. While one instruc-

tion is being executed, the next instruction is pre-fetched from the program memory.

This concept enables instructions to be executed in every clock cycle. The program

memory is In-System Programmable Flash memory.

With the relative jump and relative call instructions, the whole 512 address space is

directly accessed. All AVR instructions have a single 16-bit word format, meaning that

every program memory address contains a single 16-bit instruction.

6AT90S1200

0838H–AVR–03/02

During interrupts and subroutine calls, the return address Program Counter (PC) is

stored on the stack. The stack is a 3-level-deep hardware stack dedicated for subrou-

tines and interrupts.

The I/O memory space contains 64 addresses for CPU peripheral functions such as

Control Registers, Timer/Counters, A/D Converters and other I/O functions. The mem-

ory spaces in the AVR architecture are all linear and regular memory maps.

A flexible interrupt module has its control registers in the I/O space with an additional

global interrupt enable bit in the status register. All the different interrupts have a sepa-

rate interrupt vector in the interrupt vector table at the beginning of the

program memory. The different interrupts have priority in accordance with their interrupt

vector position. The lower the interrupt vector address, the higher the priority.

General Purpose

Figure 5 shows the structure of the 32 general purpose registers in the CPU.

Figure 5. AVR CPU General Purpose Working Registers

All the register operating instructions in the instruction set have direct and single cycle

access to all registers. The only exception is the five constant arithmetic and logic

instructions SBCI, SUBI, CPI, ANDI, ORI between a constant and a register and the LDI

instruction for load immediate constant data. These instructions apply to the second half

of the registers in the register file (R16..R31). The general SBC, SUB, CP, AND, OR

and all other operations between two registers or on a single register apply to the entire

ALU –Arithmetic Logic

Unit

The high-performance AVR ALU operates in direct connection with all the 32 general

purpose working registers. Within a single clock cycle, ALU operations between regis-

ters in the register file are executed. The ALU operations are divided into three main

categories –arithmetic, logic and bit-functions.

In-System

Programmable Flash

Program Memory

The AT90S1200 contains 1K bytes On-chip In-System Programmable Flash memory for

program storage. Since all instructions are single 16-bit words, the Flash is organized as

512 x 16. The Flash memory has an endurance of at least 1000 write/erase cycles.

The AT90S1200 Program Counter is 9 bits wide, thus addressing the 512 words Flash

program memory.

See page 37 for a detailed description on Flash data downloading.

General …

Purpose …

Working R28

Registers R29

R30 (Z-Register)

R31

AT90S1200

0838H–AVR–03/02

Program and Data

Addressing Modes

The AT90S1200 AVR RISC Microcontroller supports powerful and efficient addressing

modes. This section describes the different addressing modes supported in the

AT90S1200. In the figures, OP means the operation code part of the instruction word.

To simplify, not all figures show the exact location of the addressing bits.

Figure 6. Direct Single Register Addressing

The operand is contained in register d (Rd).

The register accessed is the one pointed to by the Z-register (R30).

Rd and Rr

Figure 8. Direct Register Addressing, Two Registers

8AT90S1200

0838H–AVR–03/02

Operands are contained in register r (Rr) and d (Rd). The result is stored in register d

(Rd).

I/O Direct Figure 9. I/O Direct Addressing

Operand address is contained in 6 bits of the instruction word. n is the destination or

source register address.

Relative Program Addressing,

RJMP and RCALL

Figure 10. Relative Program Memory Addressing

Program execution continues at address PC + k + 1. The relative address k is -2048 to

2047.

Subroutine and Interrupt

Hardware Stack

The AT90S1200 uses a 3 level deep hardware stack for subroutines and interrupts. The

hardware stack is 9 bits wide and stores the Program Counter (PC) return address while

subroutines and interrupts are executed.

RCALL instructions and interrupts push the PC return address onto stack level 0, and

the data in the other stack levels 1 - 2 are pushed one level deeper in the stack. When a

RET or RETI instruction is executed the returning PC is fetched from stack level 0, and

the data in the other stack levels 1 - 2 are popped one level in the stack.

If more than three subsequent subroutine calls or interrupts are executed, the first val-

ues written to the stack are overwritten.

AT90S1200

0838H–AVR–03/02

EEPROM Data Memory The AT90S1200 contains 64 bytes of data EEPROM memory. It is organized as a sepa-

rate data space, in which single bytes can be read and written. The EEPROM has an

endurance of at least 100,000 write/erase cycles. The access between the EEPROM

and the CPU is described on page 25 specifying the EEPROM address register, the

EEPROM data register, and the EEPROM control register. For the SPI data download-

ing, see page 44 for a detailed description.

Instruction Execution

Timing

This section describes the general access timing concepts for instruction execution and

internal memory access.

The AVR CPU is driven by the System Clock Ø, directly generated from the external

clock crystal for the chip. No internal clock division is used.

Figure 11 shows the parallel instruction fetches and instruction executions enabled by

the Harvard architecture and the fast-access register file concept. This is the basic pipe-

lining concept to obtain up to 1 MIPS per MHz with the corresponding unique results for

functions per cost, functions per clocks, and functions per power-unit.

Figure 11. The Parallel Instruction Fetches and Instruction Executions

Figure 12 shows the internal timing concept for the register file. In a single clock cycle

an ALU operation using two register operands is executed, and the result is stored back

to the destination register.

Figure 12. Single-cycle ALU Operation

System Clock Ø

1st Instruction Fetch

1st Instruction Execute

2nd Instruction Fetch

2nd Instruction Execute

3rd Instruction Fetch

3rd Instruction Execute

4th Instruction Fetch

T1 T2 T3 T4

System Clock Ø

Total Execution Time

ALU Operation Execute

Result Write Back

T1 T2 T3 T4

10 AT90S1200

0838H–AVR–03/02

I/O Memory The I/O space definition of the AT90S1200 is shown in the following table.

Note: Reserved and unused locations are not shown in the table.

All AT90S1200 I/Os and peripherals are placed in the I/O space. The different I/O loca-

tions are accessed by the IN and OUT instructions transferring data between the 32

general purpose working registers and the I/O space. I/O registers within the address

range $00 - $1F are directly bit-accessible using the SBI and CBI instructions. In these

registers, the value of single bits can be checked by using the SBIS and SBIC instruc-

tions. Refer to the instruction set chapter for more details.

For compatibility with future devices, reserved bits should be written to zero if accessed.

Reserved I/O memory addresses should never be written.

Some of the status flags are cleared by writing a logical one to them. Note that the CBI

and SBI instructions will operate on all bits in the I/O register, writing a one back into any

flag read as set, thus clearing the flag. The CBI and SBI instructions work with registers

$00 to $1F only.

The different I/O and peripherals control registers are explained in the following

sections.

Table 1. The AT90S1200 I/O Space

Address Hex Name Function

$3F SREG Status REGister

$3B GIMSK General Interrupt MaSK register

$39 TIMSK Timer/Counter Interrupt MaSK register

$38 TIFR Timer/Counter Interrupt Flag register

$35 MCUCR MCU general Control Register

$33 TCCR0 Timer/Counter0 Control Register

$32 TCNT0 Timer/Counter0 (8-bit)

$21 WDTCR Watchdog Timer Control Register

$1E EEAR EEPROM Address Register

$1D EEDR EEPROM Data Register

$1C EECR EEPROM Control Register

$18 PORTB Data Register, Port B

$17 DDRB Data Direction Register, Port B

$16 PINB Input Pins, Port B

$12 PORTD Data Register, Port D

$11 DDRD Data Direction Register, Port D

$10 PIND Input Pins, Port D

$08 ACSR Analog Comparator Control and Status Register

Andere Handbücher für AT90S1200

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Atmel Mikrocontroller Handbücher

Atmel

Atmel SAM4SD32B Bedienungsanleitung

Atmel

Atmel AT90USB162 Bedienungsanleitung

Atmel

Atmel ATmega168PB Xplained Mini Bedienungsanleitung

Atmel

Atmel AVR1605 Bedienungsanleitung

Atmel

Atmel AVR1014 Bedienungsanleitung

Atmel

Atmel AVR XMEGA D Series Bedienungsanleitung

Atmel

Atmel AT89C5130A-M Bedienungsanleitung

Atmel

Atmel ATmega328PB Xplained Mini Montage- und Bedienungsanleitung

Atmel

Atmel ATmega645 Montage- und Bedienungsanleitung

Atmel

Atmel AT90USB162 Bedienungsanleitung

Atmel

Atmel develer DevelBoard Blue Kurzanleitung

Atmel

Atmel AT43DK355 Bedienungsanleitung

Atmel

Atmel Atmel-ICE Bedienungsanleitung

Atmel

Atmel AVR042 Montage- und Bedienungsanleitung

Atmel

Atmel AVR32918 Bedienungsanleitung

Atmel

Atmel ATmega48PV Bedienungsanleitung

Atmel

Atmel MC320 Bedienungsanleitung

Atmel

Atmel CAP AT91CAP7X-DK Bedienungsanleitung

Atmel

Atmel SAM4L Xplained Pro Bedienungsanleitung

Atmel

Atmel AT89STK-09 Bedienungsanleitung

Atmel

Atmel AVR XMEGA E Montage- und Bedienungsanleitung

Atmel

Atmel XMEGA A3 series Bedienungsanleitung

Atmel

Atmel SAM L21 Xplained Pro Bedienungsanleitung

Atmel

Atmel AT43DK380 Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung