Atmel 8051 Bedienungsanleitung

Atmel 8051 Microcontrollers

Hardware Manual

Atmel 8051 Microcontrollers Hardware Manual 1

4316B–8051–02/04

Table of Contents

Section 1

The 8051 Instruction Set.......................................................................1-2

1.1 Program Status Word................................................................................1-2

1.2 Addressing Modes ....................................................................................1-3

1.3 Arithmetic Instructions...............................................................................1-5

1.4 Logical Instructions ...................................................................................1-6

1.5 Data Transfers .........................................................................................1-7

1.6 External RAM.........................................................................................1-10

1.7 Lookup Tables .......................................................................................1-10

1.8 Boolean Instructions ...............................................................................1-11

1.9 Jump Instructions....................................................................................1-13

1.10 Read-Modify-Write Instruction Features .................................................1-15

1.11 Instruction Set Summary.........................................................................1-16

1.12 Instructions That Affect Flag Settings .....................................................1-20

1.13 Instruction Table .....................................................................................1-21

1.14 Instruction Definitions..............................................................................1-24

Section 2

Common Features Description...........................................................2-64

2.1 Introduction ............................................................................................2-64

2.2 Special Function Registers .....................................................................2-65

2.3 Oscillator and Clock Circuit.....................................................................2-68

2.4 CPU Timing.............................................................................................2-69

2.5 Port Structures and Operation ................................................................2-71

2.6 Accessing External Memory....................................................................2-75

2.7 PSEN ......................................................................................................2-76

2.8 ALE .........................................................................................................2-76

2.9 Timer/Counters .......................................................................................2-78

2.10 Timer 0....................................................................................................2-78

2.11 Timer 1....................................................................................................2-81

2.12 Timer 2....................................................................................................2-86

2.13 Serial Interface........................................................................................2-91

2.14 Framing Error Detection........................................................................2-101

2.15 Automatic Address Recognition............................................................2-102

2.16 Interrupts...............................................................................................2-109

Atmel 8051 Microcontrollers Hardware Manual 1-2

Rev. 4316B–8051–02/04

Section 1

The 8051 Instruction Set

The 8051 instruction set is optimized for 8-bit control applications. It provides a variety of

fast addressing modes for accessing the internal RAM to facilitate byte operations on

small data structures. The instruction set provides extensive support for one-bit vari-

ables as a separate data type, allowing direct bit manipulation in control and logic

systems that require Boolean processing.

An overview of the 8051 instruction set is presented below, with a brief description of

how certain instructions might be used.

1.1 Program Status

Word The Program Status Word (PSW) contains several status bits that reflect the current

state of the CPU. The PSW, shown in Table 1-1 on page 3, resides in SFR space. It

contains the Carry bit, the Auxiliary Carry (for BCD operations), the two register bank

select bits, the Overflow flag, a parity bit, and two user-definable status flags.

The Carry bit, other than serving the functions of a Carry bit in arithmetic operations,

also serves as the “Accumulator” for a number of Boolean operations.

The bits RS0 and RS1 are used to select one of the four register banks shown below.

A number of instructions refer to these RAM locations as R0 through R7. The selection

of which of the four banks is being referred to is made on the basis of the bits RS0 and

RS1 at execution time.

The parity bit reflects the number of 1’s in the Accumulator: P = 1 if the Accumulator

contains an odd number of 1’s, and P = 0 if the Accumulator contains an even number of

1’s. Thus the number of 1’s in the Accumulator plus P is always even.

Two bits in the PSW are uncommitted and may be used as general purpose status flags.

The PSW register contains program status information as detailed in Table 1-1.

The 8051 Instruction Set

1-3 Atmel 8051 Microcontrollers Hardware Manual

4316B–8051–02/04

Table 1-1. PSW: Program Status Word Register

1.2 Addressing

Modes The addressing modes in the 8051 instruction set are as follows:

1.2.1 Direct Addressing

In direct addressing the operand is specified by an 8-bit address field in the instruction.

Only 128 Lowest bytes of internal Data RAM and SFRs can be directly addressed.

1.2.2 Indirect Addressing

In indirect addressing the instruction specifies a register which contains the address of

the operand. Both internal and external RAM can be indirectly addressed.

The address register for 8-bit addresses can be R0 or R1 of the selected register bank,

or the Stack Pointer. The address register for 16-bit addresses can only be the 16-bit

“data pointer” register, DPTR.

1.2.3 Register Instructions

(MSB) (LSB)

CY AC F0 RS1 RS0 OV - P

Symbol Position Name and Significance

CY PSW.7 Carry flag

AC PSW.6 Auxiliary Carry flag.

(For BCD operations.)

F0 PSW.5 Flag 0

(Available to the user for general purposes.)

RS1 PSW.4

by software to determine working register bank (see

Note).

RS0 PSW.3

OV PSW.2 Overflow flag.

- PSW.1 (reserved)

PPSW.0

Parity flag.

Set/cleared by hardware each instruction cycle to

indicate and odd/even number of “one” bits in the

accumulator, i.e., even parity.

Note:

The contents of (RS1, RS0) enable the working register banks as follows:

(0.0)-Bank 0(00H-07H)

(0.1)-Bank 1(08H-0FH)

(1.0)-Bank 2(10H-17H)

(1.1)-Bank 3(18H-1FH)

The 8051 Instruction Set

Atmel 8051 Microcontrollers Hardware Manual 1-4

4316B–8051–02/04

The register banks, containing registers R0 through R7, can be accessed by certain

instructions which carry a 3-bit register specification within the opcode of the instruction.

Instructions that access the registers this way are code efficient, since this mode elimi-

nates an address byte. When the instruction is executed, one of the eight registers in the

selected bank is accessed. One of four banks is selected at execution time by the two

bank select bits in the PSW.

1.2.4 Register-specific Instructions

Some instructions are specific to a certain register. For example, some instructions

always operate on the Accumulator, or Data Pointer, etc., so no address byte is needed

to point to it. The opcode does this itself. Instructions that refer to the Accumulator as ‘A’

assemble as accumulator-specific opcodes.

1.2.5 Immediate Constants

The value of a constant can follow the opcode in Program Memory. For example;

MOV A, # 100

loads the Accumulator with the decimal number 100. The same number could be speci-

fied in hex digits as 64H.

1.2.6 Indexed Addressing

Only Program Memory can be accessed with indexed addressing, and it can only be

read. This addressing mode is intended for reading look-up tables in Program Memory.

A 16-bit base register (either DPTR or the Program Counter) points to the base of the

table, and the Accumulator is set up with the table entry number. The address of the

table entry in Program Memory is formed by adding the Accumulator data to the base

pointer.

Another type of indexed addressing is used in the “case jump” instruction. In this case

the destination address of a jump instruction is computed as the sum of the base pointer

and the Accumulator data.

The 8051 Instruction Set

1-5 Atmel 8051 Microcontrollers Hardware Manual

4316B–8051–02/04

1.3 Arithmetic

Instructions The menu of arithmetic instructions is listed in Table 1-2. The table indicates the

addressing modes that can be used with each instruction to access the <byte> operand.

For example, the ADD A, <byte> instruction can be written as:

ADD A,7FH (direct addressing)

ADD A,@ R0(indirect addressing)

ADD A,R7 (register addressing)

ADD A,# 127(immediate constant)

The execution times listed in Table 1-2 assume a 12 MHz clock frequency and X1

mode. All of the arithmetic instructions execute in 1 µs except the INC DPTR instruction,

which takes 2 µs, and the Multiply and Divide instructions, which take 4 µs.

Note that any byte in the internal Data Memory space can be incremented or decre-

mented without going through the Accumulator.

One of the INC instructions operates on the 16-bit Data Pointer. The Data Pointer is

used to generate 16-bit addresses for external memory, so being able to increment it in

one 16-bit operation is a useful feature.

The MUL AB instruction multiplies the Accumulator by the data in the B register and puts

the 16-bit product into the concatenated B and Accumulator registers.

The DIV AB instruction divides the Accumulator by the data in the B register and leaves

the 8-bit quotient in the Accumulator, and the 8-bit remainder in the B register.

Oddly enough, DIV AB finds less use in arithmetic “divide” routines than in radix conver-

sions and programmable shift operations. An example of the use of DIV AB in a radix

conversion will be given later. In shift operations, dividing a number by 2nshifts its n bits

to the right. Using DIV AB to perform the division completes the shift in 4 µs leaves the B

Table 1-2. A list of the Atmel 8051 Arithmetic Instructions.

Mnemonic Operation Addressing Modes

Execution Time in X1

Mode

@12 MHz (µs)

Dir Ind Reg Im

ADD A, <byt>e A = A + <byte> X X X X

ADDC A,

<byte> A = A + <byte> + C X X X X 1

SUBB A,

<byte> A = A – <byte> – C X X X X 1

INC A A = A + 1 Accumulator only 1

INC <byte> <byte> = <byte> + 1 X X X 1

INC DPTR DPTR = DPTR + 1 Data Pointer only 2

DEC A A = A – 1 Accumulator only 1

DEC <byte> <byte> = <byte> – 1 X X X 1

MUL AB B:A = B ×A ACC and B only 4

DIV AB A = Int [A/B]

B = Mod [A/B] ACC and B only 4

DA A Decimal Adjust Accumulator only 1

The 8051 Instruction Set

Atmel 8051 Microcontrollers Hardware Manual 1-6

4316B–8051–02/04

The DA A instruction is for BCD arithmetic operations. In BCD arithmetic ADD and

ADDC instructions should always be followed by a DA A operation, to ensure that the

result is also in BCD. Note that DAA will not convert a binary number to BCD. The DA A

operation produces a meaningful result only as the second step in the addition of two

BCD bytes.

1.4 Logical

Instructions Table 1-3 shows the list of logical instructions. The instructions that perform Boolean

operations (AND, OR, Exclusive OR, NOT) on bytes perform the operation on a bit-by-

bit basis. That is, if the Accumulator contains 00110101B and <byte> contains

01010011B, then

ANL A,<byte>

will leave the Accumulator holding 00010001B.

The addressing modes that can be used to access the <byte> operand are listed in

Table 1-3. Thus, the ANL A, <byte> instruction may take any of the following forms.

ANL A, 7FH(direct addressing)

ANL A, @ R1(indirect addressing)

ANL A, R6(register addressing)

ANL A, # 53H(immediate constant)

All of the logical instructions that are Accumulator specific execute in 1 µs (using a

12 MHz clock and X1 mode). The others take 2 µs.

Table 1-3. A list of the Atmel 8051 Logical Instructions

Mnemonic Operation Addressing Modes Execution Time

@ 12MHz (µs)

Dir Ind Reg Imm

ANL A, <byte> A = A AND <byte> X X X X 1

ANL <byte>, A <byte> = <byte> AND A X 1

ANL <byte>, #

data <byte> = <byte> AND # data X 2

ORL A, <byte> A = A OR <byte> X X X X 1

ORL <byte>, A <byte> = <byte> OR A X 1

ORL <byte>, #

data <byte> = <byte> OR # data X 2

XRL A, <byte> A = A XOR <byte> X X X X 1

XRL <byte>, A <byte> = <byte> XOR A X 1

XRL <byte>, #

data <byte> = <byte> XOR # data X 2

CLR A A = 00H Accumulator only 1

CLP A A = NOT A Accumulator only 1

RL A Rotate ACC Left 1 bit Accumulator only 1

RLC A Rotate Left through Carry Accumulator only 1

RR A Rotate ACC Right 1 bit Accumulator only 1

RRC A Rotate Right through Carry Accumulator only 1

SWAP A Swap Nibbles in A Accumulator only 1

The 8051 Instruction Set

1-7 Atmel 8051 Microcontrollers Hardware Manual

4316B–8051–02/04

Note that Boolean operations can be performed on any byte in the internal Data Memory

space without going through the Accumulator. The XRL <byte>, # data instruction, for

example, offers a quick and easy way to invert port bits, as in

XRL P1, #OFFH

If the operation is in response to an interrupt, not using the Accumulator saves the time

and effort to stack it in the service routine.

The Rotate instructions (RL A, RLC A, etc.) shift the Accumulator 1 bit to the left or right.

For a left rotation, the MSB rolls into the LSB position. For a right rotation, the LSB rolls

into the MSB position.

The SWAP A instruction interchanges the high and low nibbles within the Accumulator.

this is a useful operation in BCD manipulations. For example, if the Accumulator con-

tains a binary number which is known to be less than 100, it can be quickly converted to

BCD by the following code:

MOV B, #10

DIV AB

SWAP A

ADD A,B

Dividing the number by 10 leaves the tens digit in the low nibble of the Accumulator, and

the ones digit in the B register. The SWAP and ADD instructions move the tens digit to

the high nibble of the Accumulator, and the ones digit to the low nibble.

1.5 Data Transfers

1.5.1 Internal RAM

Table 1-4 shows the menu of instructions that are available for moving data around

within the internal memory spaces, and the addressing modes that can be used with

each one. With a 12 MHz clock and X1 mode, all of these instructions execute in either

1 or 2 µs.

The MOV <dest>, <src> instruction allows data to be transferred between any two inter-

nal RAM or SFR locations without going through the Accumulator. Remember the Upper

128 bytes of data RAM can be accessed only by indirect, and SFR space only by direct

addressing.

Note that in all 8051 devices, the stack resides in on-chip RAM, and grows upwards.

The PUSH instruction first increments the Stack Pointer (SP), then copies the byte into

the stack. PUSH and POP use only direct addressing to identify the byte being saved or

restored, but the stack itself is accessed by indirect addressing using the SP register.

The 8051 Instruction Set

Atmel 8051 Microcontrollers Hardware Manual 1-8

4316B–8051–02/04

This means the stack can go into the Upper 128, if they are implemented, but not into

SFR space.

The Upper 128 are not implemented in the 8 standard 8051, nor in their ROMless. With

these devices, if the SP points to the Upper 128 PUSHed bytes are lost, and POPped

bytes are indeterminate.

The Data Transfer instructions include a 16-bit MOV that can be used to initialize the

Data Pointer (DPTR) for look-up tables in Program Memory, or for 16-bit external Data

Memory accesses.

The XCH A, <byte> instruction causes the Accumulator and addressed byte to

exchange data.

The XCHD A, @ Ri instruction is similar, but only the low nibbles are involved in the

exchange.

The see how XCH and XCHD can be used to facilitate data manipulations, consider first

the problem of shifting an 8-digit BCD number two digits to the right. Table 1-5 shows

how this can be done using direct MOVs, and for comparison how it can be done using

XCH instructions. To aid in understanding how the code works, the contents of the reg-

isters that are holding the BCD number and the content of the Accumulator are shown

alongside each instruction to indicate their status after the instruction has been

executed.

After the routine has been executed, the Accumulator contains the two digits that were

shifted out on the right. Performing the routine with direct MOVs uses 14 code bytes and

9 µs of execution time (assuming a 12 MHz clock and X1 mode). The same operation

with XCHs uses less code and executes almost twice as fast.

Table 1-4. Atmel 8051 Data Transfer Instructions that Access Internal Data Memory

Space

Mnemonic Operation Addressing Modes Execution Time

@ 12MHz (µs)

Dir Ind Reg Imm

MOV A, <src> A = <src> X X X X 1

MOV <dest>, A <dest> = A X X X 1

MOV <dest>,

<src> <dest> = <src> X X X X 2

MOV DPTR, #

data 16 DPTR = 16-bit immediate

constant X2

PUSH <src> INC SP: MOV “@SP”, <scr> X 2

POP <dest> MOV <dest>, “@SP”: DEC SP X 2

XCH A, <byte> ACC and <byte> Exchange Data X X X 1

XCHD A, @Ri ACC and @ Ri exchange low

nibbles X1

The 8051 Instruction Set

1-9 Atmel 8051 Microcontrollers Hardware Manual

4316B–8051–02/04

To right-shift by an odd number of digits, a one-digit shift must be executed. Table 1-6

shows a sample of code that will right-shift a BCD number one digit, using the XCHD

instruction. Again, the contents of the registers holding the number and of the Accumu-

lator are shown alongside each instruction.

First, pointers R1 and R0 are set up to point to the two bytes containing the last four

BCD digits. Then a loop is executed which leaves the last byte, location 2EH, holding

the last two digits of the shifted number. The pointers are decremented, and the loop is

Table 1-5. Shifting a BCD Number Two Digits to the Right

2A 2B 2C 2D 2E ACC

MOV A,2EH

MOV 2EH, 2DH

MOV 2DH, 2CH

MOV 2CH, 2BH

MOV 2BH, # 0

Note: Using direct MOVs: 14 bytes, 9 µs

2A 2B 2C 2E 2E ACC

CLR A

XCH A,2BH

XCH A,2CH

XCH A,2DH

XCH A,2EH

Note: Using XCHs: 9 bytes, 5 µs

Table 1-6. Shifting a BCD Number One Digit to the Right

2A 2B 2C 2D 2E ACC

MOVR1,#2EH 0012345678XX

MOVR0,#2DH 0012345678XX

loop for R1 = 2EH:

LOOP:MOVA,@R1 001234567878

XCHD A, @R0 00 12 34 58 78 76

SWAPA 001234587867

MOV@R1,A 001234586767

DEC R1 00 12 34 58 67 67

DEC R0 00 12 34 58 67 67

CJNE R1, #2AH, LOOP

loop for R1 = 2DH: 00 12 38 45 67 45

loop for R1 = 2CH: 00 18 23 45 67 23

loop for R1 = 2BH: 08 01 23 45 67 01

CLRA 080123456700

XCHA,2AH 000123456708

Inhaltsverzeichnis

Andere Atmel Mikrocontroller Handbücher

Atmel

Atmel AVR2131 Bedienungsanleitung

Atmel

Atmel AVR262 Montage- und Bedienungsanleitung

Atmel

Atmel AVR XMEGA D Series Bedienungsanleitung

Atmel

Atmel ATF15 DK3-U Series Bedienungsanleitung

Atmel

Atmel ATZB-EVB-24-SMA Bedienungsanleitung

Atmel

Atmel ATSAMB11 BluSDK SMART Bedienungsanleitung

Atmel

Atmel AT91CAP9A-DK Bedienungsanleitung

Atmel

Atmel STK200 Bedienungsanleitung

Atmel

Atmel ATtiny26 Bedienungsanleitung

Atmel

Atmel AVR AT90S4434 Bedienungsanleitung

Atmel

Atmel STK512 Bedienungsanleitung

Atmel

Atmel AT88CK101BK8 Installationshandbuch

Atmel

Atmel SAM4N Xplained Pro Bedienungsanleitung

Atmel

Atmel ATmega161 Bedienungsanleitung

Atmel

Atmel AVR ATtiny15L Bedienungsanleitung

Atmel

Atmel AVR2052 Bedienungsanleitung

Atmel

Atmel AVR 1908 Bedienungsanleitung

Atmel

Atmel AVR ATmega103 Bedienungsanleitung

Atmel

Atmel 80C51 Montage- und Bedienungsanleitung

Atmel

Atmel AVR ATtiny15L Betriebsanleitung

Atmel

Atmel AVR1605 Bedienungsanleitung

Atmel

Atmel AT32UC3L064 Bedienungsanleitung

Atmel

Atmel AT01607 Montage- und Bedienungsanleitung

Atmel

Atmel SAM L21 Xplained Pro Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung