Atmel ATmega128A-STK600 Montage- und Bedienungsanleitung

APPLICATION NOTE

Hardware and Software Getting Started

ATmega128A-STK600

Introduction

An easy and fast way to start developing and evaluating the ATmegaS128 device

is to use the ATmega128A industrial version with the STK600 starter-kit.

This document guides you step by step to setup the hardware and software, to

program and run your first code with the ATmega128A device.

Requirements

To use this “Getting Started” document you need to gather the following

materials:

- One STK600 evaluation kit (ATSTK600)

- One STK600-RC064M-9 Routing board (ATSTK600-RC09)

- One STK600-TQFP64 Socket Board with a ZIF socket. (ATSTK600-SC02)

- One ATmega128A in TQFP64 package

- Atmel Studio available from : http://www.atmel.com/Microsite/atmel-studio

- “ATmegaS128_led_chaser.zip” software File

Objective

The aim is prepare the hardware, program and run a short demo based on the

“led chaser” software.

Atmel-41074B-Aero-Hardware and Software Getting Started-05/2016

ATmega128A-STK600 [APPLICATION NOTE]

Atmel-41074B-Aero-Hardware and Software Getting Started-05/2016

1 Hardware Configuration

1.1 Step 1.

Unpack the STK600 kit and install the RC064M-9 routing board as shown on the figure below.

ATmega128A-STK600 [APPLICATION NOTE]

Atmel-41074B-Aero-Hardware and Software Getting Started-05/2016

1.2 Step 2.

Install the STK600-TQFP64 socket board as shown on the figure below.

ATmega128A-STK600 [APPLICATION NOTE]

Atmel-41074B-Aero-Hardware and Software Getting Started-05/2016

1.3 Step 3.

Connect an USB cable between your workstation and the STK600 board and connect an 8-wires flat cable

between the ports A(0-7) and LED(0-7) as shown in the figure below. Before connecting the USB cable, set the

power switch to “Off” position. Those two cables are supplied in the STK600 kit.

ATmega128A-STK600 [APPLICATION NOTE]

Atmel-41074B-Aero-Hardware and Software Getting Started-05/2016

1.4 Step 4.

Install the ATmega128A device into the TQFP64 socket being careful to insert it in the right direction by

matching together the indexes of the package and the device as shown in the figure below.

1.5 Step 5.

Verify that the jumpers and the switch are configured as shown on the figure below. The jumpers VTARGET,

RESET, AREF0, AREF1 must be set and the clock switch must be set to “INT” position.

ATmega128A-STK600 [APPLICATION NOTE]

Atmel-41074B-Aero-Hardware and Software Getting Started-05/2016

1.6 Step 6.

Connect a 10-wires flat cable on the JTAG connector as shown on the figure below. The cable is supplied in

the STK600 kit.

Move the power switch to “ON” position. The hardware configuration is now complete. The next step will

consist to run the application software.

ATmega128A-STK600 [APPLICATION NOTE]

Atmel-41074B-Aero-Hardware and Software Getting Started-05/2016

2 Software Configuration

This section guides you in few steps to prepare your workstation to program and run the “led chaser” demo.

Prerequisite 1.: download Atmel Studio from the URL http://www.atmel.com/Microsite/atmel-studio and install

it on your workstation.

Prerequisite 2.: unzip the “led chaser” demo file.

2.1 Step 7.

Double click on the file “Led_Chaser.atsln”. It makes run Atmel Studio (if a window requesting an update

appears, you can close it).

2.2 Step 8.

Click on the programming Icon as shown on the figure below.

ATmega128A-STK600 [APPLICATION NOTE]

Atmel-41074B-Aero-Hardware and Software Getting Started-05/2016

2.3 Step 9.

A window should pop as shown on the figure below.

Select STK600 as tools, ATmega128A as device and JTAG as Interface then click on the “Apply” button.

In return, the system should display the information shown on the figure below, meaning that the hardware

configuration has been recognized by the system.

ATmega128A-STK600 [APPLICATION NOTE]

Atmel-41074B-Aero-Hardware and Software Getting Started-05/2016

2.4 Step 10.

Click on the “Read” button to get the signature bytes of the ATmega128A.

The voltage supply of the ATmega128A device can be adjusted from your workstation. If the voltage level is

close to zero, it is not possible to read the signature bytes. Therefore the voltage supply must be tuned.

You should read the value 0x1E9702 meaning that the system is able to communicate with the ATmega128A

device. If an error message comes up, check the device voltage by clicking on the “Read” button. If it is not

possible, click on the “board settings” option from the left menu.

Note: The ATmegaS128 is a 3.3V device while the ATmega128A is a 2.7-5.5V device. Therefore, the

ATmega128A lets you the choice between 3.3V or 5V. The pictures of this document are provided with the 5V

option.

ATmega128A-STK600 [APPLICATION NOTE]

Atmel-41074B-Aero-Hardware and Software Getting Started-05/2016

Adjust the voltage level by means of the cursor as shown on the figure below then click on the “Write” button.

Verify the target voltage and the availability of the signature bytes (0x1E9702).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Atmel Mikrocontroller Handbücher

Atmel

Atmel AVR365 Bedienungsanleitung

Atmel

Atmel UC3-L0 Xplained Montage- und Bedienungsanleitung

Atmel

Atmel 80C51 Montage- und Bedienungsanleitung

Atmel

Atmel SAM L21 Xplained Pro Bedienungsanleitung

Atmel

Atmel SAM L22G Bedienungsanleitung

Atmel

Atmel AVR AVR350 Montage- und Bedienungsanleitung

Atmel

Atmel QTouch Montage- und Bedienungsanleitung

Atmel

Atmel ATmega32M1 Bedienungsanleitung

Atmel

Atmel AVR4901 Montage- und Bedienungsanleitung

Atmel

Atmel AVR AT90CAN32 Bedienungsanleitung

Atmel

Atmel AVR XMEGA D Series Bedienungsanleitung

Atmel

Atmel AT91FR40162S Bedienungsanleitung

Atmel

Atmel 80C51 Montage- und Bedienungsanleitung

Atmel

Atmel AT43DK370 Bedienungsanleitung

Atmel

Atmel AT90S2313 Bedienungsanleitung

Atmel

Atmel ATF15 DK2 Series Bedienungsanleitung

Atmel

Atmel AT88RF1354 Bedienungsanleitung

Atmel

Atmel STK512 Bedienungsanleitung

Atmel

Atmel AVR042 Montage- und Bedienungsanleitung

Atmel

Atmel megaAVR Bedienungsanleitung

Atmel

Atmel ATmega48A Bedienungsanleitung

Atmel

Atmel ATSAMB11 BluSDK SMART Bedienungsanleitung

Atmel

Atmel ATtiny104 Xplained Nano Bedienungsanleitung

Atmel

Atmel ARIS+ AT88SC-ADK2 Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung