ATN Aries MK 6650 Bedienungsanleitung

AMERICAN

TECHNOLOGIES

NETWORK

CORP.

u s e r ` s g u i d e

Aries MK 6600/6650

Aries MK 7700/7750

Aries MK 8700/8750

The information in this manual furnished for information use only, is subject to change without notice, is not to be

construed as a commitment by ATN Corp.

ATN Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.

Master power

(ON/OFF) switch

Control

panel

Remote control panel

Battery

compartment

Manual focus lens;

5’ to infinity

100m Infra-red

illuminator Proximity sensor

Windage

Elevation

Fixator screws

Mounting bracket (mounts to standard

U.S. 7/8” weaver rail)

Diopter

Remote control

Reticle Pattern

Selector button

Aries MK6650/7750/8750

Aries MK6600/7700/8700

The information in this manual furnished for information use only, is subject to change without notice, is not to be

construed as a commitment by ATN Corp.

ATN Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.

APPLICATION

The Aries MK6600/6650/7700/7750/8700/8750 night vision weapon scope is a complex computer-

ized system for the observation of objects at low light levels. Containing an onboard computer these

scopes are some of the most advanced night vision weapon scopes in the world.

The Aries MK6600/6650/7700/7750/8700/8750 consists of the objective lens assembly, ocular

lens assembly and the body. The body contains the image intensifier tube assembly with the inte-

grated high voltage power source. The body also houses the electronics for the reticle, the computer

console for the “Smart Technology” as well as the battery compartment. The 100M infra-red illumi-

nator is located on the top of the unit.

The objective lens protective cover (not shown) is designed to protect the lens from scratches and

abrasions. This cover also protects the image intensifier tube from exposure to daylight or other

bright light sources. The protective cover acts as a daylight filter, note the pinhole in the center of

the lens cap.

MASTER POWER SWITCH

The Master ON/OFF switch is to be found on top of

MK6600/6650/7700/7750/8700/8750. Once the

scope’s master power is switched on you can adjust

the scope using the buttons on the control box.

CONTROL PANEL

The control box with the cluster of three buttons on it can be found on the left side of the Aries

MK6600/6650/7700/7750/8700/8750. ”SL” button acts as a three-way selection toggle. By press-

ing it once you will see one of three colored diodes located on the rear side of the control box light

up. Make sure to keep both eyes open; your right eye is expected to aim through the scope so that

your left eye perceives the changes on the rear side of the control box. “+” and “-” buttons are used

to correspondingly increase or decrease adjustments for a chosen function.

The three colored led diodes represent the scope function mode. “B” stands for brightness of the

light intensifier tube, “R”- for reticle brightness, and “I”- for IR illuminator brightness.

Brightness LED

Reticle brightness LED

Illuminator brightness LED

“+” adjustment button

“-” adjustment button

“SL” selection button

Master power switch

INFRA-RED ILLUMINATION

By pressing “SL” button three times you can switch to Red diode

“I”. Red diode represents 100M infra-red illuminator’s bright-

ness adjustment mode. Adjustments can be easily observed

through the Aries scope while pressing” +” /” -” adjustment but-

tons.

Infra-red illuminators, or IR illuminators, are common to night

vision. The IR light greatly enhances to the performance of the

Aries MK6600/6650/7700/7750/8700/8750 while remaining

almost totally invisible to the unaided eye.

Power up the Aries scope in a dark environment. Find an object

and examine it with IR off, then on. You could observe illumina-

tion difference. It is important to remember that the IR illuminator

is simply an infra-red light source and like any light source it may

loose its effectiveness over long distances.

To change the field of coverage from the IR illuminator, focus

the beam by turning IR illuminator lens to slightly alter the beam

width.

RETICLE BRIGHTNESS ADJUSTMENT

By pressing the SL button twice you switch to a yellow “R”

diode next to the green one. The yellow diode represents the

reticle’s brightness. Adjustments could be easily seen if you look

through the Aries MK6600/6650/7700/7750/8700/8750 while

pressing “ +” /” -” adjustment buttons.

To adjust the brightness of the reticle or to turn it off use the con-

trol box buttons located on the side of the unit. Press and hold “+

“or” -” adjustment buttons while the yellow diode is on and see

brightness changes looking through the scope. After appropriate

level of brightness has been set release the button.

LIGHT INTENSIFIER TUBE BRIGHTNESS ADJUSTMENT

The green led “B” represents the light intensifier tube power

ratio. Once this is lit you can adjust the brightness of the light

intensifier with the “+” and “-” adjustment buttons.

Green LED “B”

Yellow LED “R”

Red LED “I”

SLEEP MODE

One of the greatest new features that your Smart scope has is the SLEEP mode. This feature has

been designed to considerably extend the period of scope’s functioning, to set the scope to memo-

rize your initial settings and endure battery’s life (by settings we mean only digital settings which

include brightness of the tube, brightness of the reticle, and magnitude of the IR.) Here is a descrip-

tion as to now the sleep mode functions:

The scope will automatically shut down if it does not sense any activity (i.e. pressing any of the but-

tons or simply moving the scope back and forth away from your face) for 20 minutes. When activat-

ing the sleep mode the scope will first warn you by turning off the reticle for 10 seconds. If you intend

is to keep using the scope simply touch any key and the scope will reactivate.

One of the reasons for the SLEEP mode being programmed into your scope is to keep the light

intensifier tube and batteries safe in case you forget to turn your unit off. If you notice that the reticle

turned off after 20 minutes just push the SL button and the scope will return to its previous settings.

To put your scope in the “SLEEP” mode any time, just push the SL button and “-” simultaneously.

Push SL to return to previous settings and the SMART scope will remember them. This feature will

come very handy, if you are waiting for game to come: you can prepare all of the settings, place

the unit in SLEEP mode and activate it precisely when you need it. To disable the proximity sensor

press SL and “+” simultaneously. In order to turn the proximity sensor back on, press SL and “+”

simultaneously again.

NOTE: The scope is capable of running in SLEEP mode for more than 10 (ten) days and is ready for

use at any moment. Remember, you don’t have to turn the unit off while you are using it (“Smart” sight

remembers all the settings). Use the master ON/OFF switch only to store the scope.

PROXIMITY SENSOR

If you turn the proximity sensor on it will activate the

scope when brought to your eye. The proximity sensor

disables the scope when you take it away from your

face. This feature has been introduced to prolong the

life of the tube and the battery.

To turn the proximity sensor on press SL and + at the

same time.

To disable the proximity sensor press SL and + at the

same time again.

NOTE: Proximity sensor would not turn on automati-

cally after master power has been switched on.

Proximity sensor

FOCUSING

To focus the Aries MK6600/6650/7700/7750/8700/8750 you need to adjust the diopter first thing.

Simply turn the diopter clockwise until it stops. Then concentrate on any object and slowly turn the

diopter back counter clockwise until the grain in the image is sharp.

When you are under low-light conditions and the daylight filter is off you may focus the front lens for

the image to be sharp. The diopter is not to be adjusted.

NOTE: The front lens should be readjusted for viewing objects at different distances.

You scope has ability to focus either long range or short. To adjust focus unlock front lens with the

Large Allen wrench (included with scope). After focusing lens to desired distance re-lock lens in

place to insure no movement of reticle while shooting.

NOTE:To remove the front lens to clean, you must unlock the above set screw.

MOUNTING THE ARIES MK6600/6650/7700/7750/8700/8750

1. Slightly loosen the horizontal and vertical fixing screws on the 7/8” weaver rail built into the

MK6600/6650/7700/7750/8700/8750.

2. Place the scope on the dovetail mount of the fire arm making certain that the mount aligns with the

receptor attachment screw groove. Adjust as necessary.

3. Tighten the horizontal fixing screws.

NOTE: Receptor attachment screws may need to be tightened after continuous shooting.

Fixator screws

Diopter

Front lens

Insert large allen wrench

here to lock/unlock and

to remove lens

USING THE REMOTE CONTROL

Below the control box you can find the panel with two

screws to fix Aries MK6600/6650/7700/7750/8700/

8750.

To plug in the remote control, remove the screws and the

small panel to disclose the inlet.

The three remote control buttons’ function similarly to

control box buttons. Once the remote control is plugged in

you may use both panels to adjust the scope.

The remote control can be attached to the weapon of your

choice through whatever means best suiting your shoot-

ing style and grip. We suggest an elastic Velcro® loop

fastener similar to the trigger switches found on the weapon mounted laser pointers.

RANGE FINDER

The range finder reticle in your Aries MK6600/7700/

8700 has been designed to assist you in determining

the range of your target. These distances are based

on a 6’ target. A 6’ target fits between the numbered

baseline (the three short horizontal lines just next to

the numbers) and the main horizontal line. If the 6’

target fits between the 1 and the right horizontal posts

of the main line the target is 100 yards away. If the

same target fits between the 2 and the right post of the

main line the target is 200 yards away. The same is

with the three, the target is 300 yards away.

If the “Red on Green” reticule is not perpendicular to

the bore of the rifle, it can be adjusted by doing the

following:

1. Unscrew the cover between the windage and eleva-

tion adjustments.

2. Loosen the flat-head screw about 1/2 - 3/4 of a turn.

3. Rotate the central threaded shaft with two notches

as needed (make sure that you do not rotate the round

plate mounted on this shaft individually. They will

rotate together, but if you move the plate itself, if will

interfere with the focus of the reticule).

WINDAGE AND ELEVATION

To adjust vertical and horizontal positions for the

Aries MK6600/6650/7700/7750/8700/8750 turn the

elevation and windage adjustment mechanisms. Each

click equals to 1/8 inch at 100 yards. Do not use force

having reached the maximum of rotation.

If a 6` target fits between

these two lines then the

target is 100 yards away

If a 6` target fits between

these two lines then the

target is 300 yards away

Windage Elevation

3 2 1

PREPARATION FOR OPERATION

Before getting started make sure to follow these steps:

• Take the scope out of the case.

• Insert the batteries into their housing with the polarity order shown on the main body of the unit.

• Switch on your MK6600/6650/7700/7750/8700/8750 scope by the master power switch, make

sure the protective lens cover is still attached to the lens.

• We expect your right eye to aim through the scope. Keep both of your eyes open so you are able

to see the color-coded LEDs with your left eye.

• In order to assure the proper functioning of the proximity sensor make certain that the protective

glass surface of the sensor is always clean.

• When the scope is first powered up the initial settings are:

- Light intensifier tube brightness -100%

- Reticle brightness -100%

- Illuminator brightness -100%.

• Observe the scene and adjust the diopter for optimal image clarity.

• You may now enter the dark environment or simply shut the lights off in order to darken the room.

• Remove the lens cap/daylight filter.

• Observe the scene and adjust the front lens for ideal focus.

• Adjust the digital features as needed.

• To increase the battery life the LED diodes go off after 10 seconds.

• You will need to focus for different distances.

• Take your time to learn about your “Smart” scope. It will take practice to properly use this device.

As you use this scope you will be able to improve your speed of focusing, as well as sharpness of

image.

• Have fun and enjoy.

1 MOA

60 MOA

Open Cross Hair

2 MOA

Dot 1 MOA

60 MOA

Post

6 MOA

60 MOA

1 MOA

Post with Dot 60 MOA

1 MOA

60 MOA

6 MOA

Cross Hair

RETICLE PATTERNS

The Aries MK6650/7750/8750 scopes comes

with five reticle patterns:

• Dot

• Post

• Post with Dot

• Open Cross Hair

• Cross Hair

You can choose your preferred pattern by

pushing the Reticle Pattern Selector button. Reticle Pattern

Selector button

Aries

MK6650

MK7750

MK8750

CLEANING THE EYEPIECE

You may need to clean the eyepiece of the riflescope from time to time in order to guarantee top per-

formance. When you receive your riflescope you should check for dust on the eyepiece of the unit.

First you will need to remove the eyepiece. To do that you will need to initially loosen the 2 set screws

that can be found on the base. Then unscrew the eyepiece counter-clockwise to remove it.

NOTE: You do not have to remove the set screws completely, they are very small and easy to mis-

place.

CAUTION: Use only Photographic lens cleaning tissue on these surfaces. Be careful not to scratch

or smudge any of these surfaces. When using compressed air to blow dust away, make sure to avoid

inverting the can while spraying. This can cause frozen propellant to exit the can, which can cause

serious problems with the glass and phosphor screen.

WARNINGS AND CAUTIONS

• Always remember to turn off the Aries MK6600/6650/7700/7750/8700/8750 when it is not in use.

If you do not plan on using your aries scope for a period of more than 10 days, you should remove

the batteries.

• Keep lens cap/daylight filter on when not in use.

• Avoid contact with dust, steam, and gas.

• The Aries MK6600/6650/7700/7750/8700/8750 are not harmful to the user or the environment.

• Do not disassemble except to clean the front lens and the eyepiece: it will void your warranty.

• Evaluate the scopes function by looking through it in a lit environment with the daylight filter lens

cap on. Never use in daylight without the daylight filter lens cap on. Do not surpass ten minutes of

testing.

• Never point the Aries MK6600/6650/7700/7750/8700/8750 at a bright light source. If the scope

shuts off automatically after directing it at a bright light source, turn the unit off and wait 1 - 2 min-

utes before turning the unit back on.

• Adverse atmospheric conditions such as fog, smog, or haze and a lack of ambient light (moon or

starlight) may diminish the effective viewing distance. All technical data for this unit was compiled

in a controlled environment.

TROUBLE SHOOTING

Q: Flashes, flickers, or clicking occur while operating

S: If it occurs within the first five minutes of inserting new batteries, it is normal and the device will

resume normal operation soon thereafter. If it occurs for more than 10 minutes, contact your dealer

or other authorized service representative for service instructions.

Q: Dark spots on screen.

S: These are cosmetic blemishes in the intensifier tube. They are a by-product of the process of

manufacturing night vision tubes. They will not impede your viewing ability.

Q: Image not clear.

S: Adjust focus ring. If problem persists, increase viewing distance

Q: Fixed-pattern noise in a honeycomb shape.

S: Usually a cosmetic blemish characterized by a faint honeycomb-type pattern. This usually occurs

when viewing very bright lights. Adjust the potentiometer, to reduce brightness.

Q: A pattern of dark thin lines which look like chicken wire.

S: Turn on illuminator, if purchased. If illuminator doesn’t brighten image, replace batteries. If

problem persists, contact ATN for service instructions.

FEATURES

• Digital “Smart technology”

• Total darkness technology

• Internally adjustable lit reticle for windage and elevation

• Automatic brightness control

• Range finder

• Built in 100m IR illuminator

• Mounts to standard U.S. weaver

• Recoil & flash resistant intensifiertube

• Auto “Sleep” mode

• Video/35mm camera adaptable

• Superb multi-coated 6 element lens system

• Manufactured exclusively by ATN

• Two year warranty

• Assembled in U.S.A.

SPECIFICATION

Total Darkness Technology...........Standard

“Smart” Technology ......................Standard

Magnification ................................4x

Intensifier Tube .............................US 2nd Gen. (MK6600/6650)

......................................................US 3rd Gen. (MK7700/7750)

......................................................US 4th Gen. (MK8700/8750)

Detection Range ...........................250 m (MK6600/6650)

......................................................300 m (MK7700/7750)

......................................................400 m (MK8700/8750)

Recognition Range .......................175 m (MK6600/6650)

......................................................225 m (MK7700/7750)

......................................................275 m (MK8700/8750)

Lens System .................................6 element 90 mm; F1.7

Field of View .................................12°

Diopter Adjustment........................±5

Resolution ....................................34 lp/mm (MK6600/6650)

......................................................51 lp/mm (MK7700/7750)

......................................................64 lp/mm (MK8700/8750)

Range of Focus ............................1.8 m to infinity

Reticle ...........................................Red on green rangefinder

......................................................5 reticle patterns (MK6650, MK7750, MK8750)

Controls.........................................Digital and remote

Power Supply ...............................Two 3 volt lithium

Battery Life ...................................10-20 hours

Dimensions ...................................300 mm x 110 mm x 85 mm

Operating Temperatures ..............-40°C to +40°C

Weight ....................................... 1.5 kg

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ATN Zielfernrohr Handbücher

ATN

ATN Ultra Sight Digital Bedienungsanleitung

ATN

ATN ThOR-HD 384 2 - 8x Bedienungsanleitung

ATN

ATN Daytime 3-9x55LU Bedienungsanleitung

ATN

ATN Ultra Sight DC Bedienungsanleitung

ATN

ATN Trident Pro2x-2 Bedienungsanleitung

ATN

ATN Professional 12-36x80 Bedienungsanleitung

ATN

ATN 10x65Z-Army Mil-Dot Bedienungsanleitung

ATN

ATN Aries MK300 Bedienungsanleitung

ATN

ATN MARS4-4 Bedienungsanleitung

ATN

ATN 4-12x80 DNS Bedienungsanleitung

ATN

ATN Digital Ultra Sight Bedienungsanleitung

ATN

ATN PS-40 Bedienungsanleitung

ATN

ATN ELCAN SpecterCT Bedienungsanleitung

ATN

ATN Daytime Series Bedienungsanleitung

ATN

ATN Mars4x-3P Bedienungsanleitung

ATN

ATN Aries 6800C Defender Bedienungsanleitung

ATN

ATN ThOR 2 B&W Bedienungsanleitung

ATN

ATN PS40-3P Bedienungsanleitung

ATN

ATN Aries MK390 "Paladin" Bedienungsanleitung

ATN

ATN nIGHT aRROW 4 Bedienungsanleitung

ATN

ATN Trident Pro2x-2 Bedienungsanleitung

ATN

ATN Aries MK410 "Spartan" Bedienungsanleitung

ATN

ATN Mars 2 Bedienungsanleitung

ATN

ATN Mars4x-3 Bedienungsanleitung

Beliebte Zielfernrohr Handbücher anderer Marken

Leupold

Leupold Hunting Equipment Benutzerhandbuch

Newcon Optik

Newcon Optik DN482 Bedienungsanleitung

Bushnell

Bushnell ET3124F Bedienungsanleitung

Newcon Optik

Newcon Optik NVS-33 Bedienungsanleitung

Nikon

Nikon 8442 - Omega Muzzleloader Scope 1.65-5x36 Bedienungsanleitung

Pulsar

Pulsar Trail Series Bedienungsanleitung

FLIR

FLIR ThermoSight T50 Bedienungsanleitung

Pulsar

Pulsar Digisight Ultra N450 Bedienungsanleitung

Nikon

Nikon 1.65-5x36 Bedienungsanleitung

Nikon

Nikon OMEGA Muzzleloading 3-9x40 Bedienungsanleitung

Zeiss

Zeiss Classic Diatal T Series Bedienungsanleitung

Nikon

Nikon 4-16x50SF - Monarch Riflescope - BDC Bedienungsanleitung

COT

COT NM-108 BC Bedienungsanleitung

Nikon

Nikon 4-16x42SF - Monarch Riflescope Bedienungsanleitung

Minox

Minox ZP5 3-15x50 Bedienungsanleitung

Bushnell

Bushnell 20-4124 Bedienungsanleitung

StreamLight

StreamLight STINGER 700025 Bedienungsanleitung

Bushnell

Bushnell 71-3946 Bedienungsanleitung