ATOMSTACK MAKER AC1 Bedienungsanleitung
ATOMSTACK MAKER AC1 User Manual
English
F03-0107-0AA1
Version: A
Table of contents
1. Declaration
2. Precautions
3. Assembly steps
4. Preparation (installation and debugging)
5. Calibrate Camera Lens
6. Calibrate Camera Alignment
7. How to use positioning
8. How to record video
2
2
3
4
5-6
7-8
9
10
1
1 Declaration
2 Precautions
ATOMSTACK MAKER AC1 camera functions need to be controlled by LightBurn, please download the ocial version of LightBurn
software. LightBurn is a third-pay software, so ATOMSTACK seice is not responsible for any loss caused by the operation of LightBurn,
the rmware of ATOMSTACK has been tested in detail by ATOMSTACK, and the situation of incompatibility with software or hardware is
still possible occur. If an error occurs due to incompatibility, you can contact our customer depament seice for technical suppo.
suppo@atomstack.com
1. Do not collide or move the camera during the calibration process.
2. Do not collide or move the camera after the alignment of the calibration camera is completed. If the camera is collided and the camera
is shifted left and right, the camera lens and camera alignment need to be recalibrated.
3. Cardboard and dot cards need to be at.
2
3 Assembly steps
3
4. Preparation (installation and debugging)
4.1 Place the 100mm*100mm cardboard atly in the working area of the engraving machine, x the focus, and then return the laser to
the origin of the machine to engrave a pattern of 400*400mm.
4.2 Fix the assembled camera on the machine (Picture 1), Pay attention to keep the position of the machine and the paper unchanged;
adjust the position of the camera so that the distance between the working plane and the camera lens is 420mm (Picture 2), and make the
center of the camera lens align with the cross position as much as possible (Picture 3).
Picture 1 Picture 2 Picture 3
420mm
4
400*400
5 Calibrate Camera Lens
5.1 Check camera control in the Window drop-down menu 5.2 Select the camera in the camera control window.
5.3 Right-click in the camera control window and
click Calibrate Camera Lens.
5.4 Click Update Overlay, select the Camera name, Standard Lens, and
None - do full calibration in the pop-up window.
5
5.5 Click to close Honeycomb check enabled.
5.7 Place the dot card in ve positions, left, right, top, bottom, and middle, and capture 5 times. If the captured result Score≤1 and the
pattern is slightly deformed or not deformed, click Next; if the pattern cannot be captured, repeat step 2 Fine-tune the lens or move the
position of the dot card to capture again (the recommended order of dot card placement is left, right, top, bottom, and middle) until the
capture is successfully completed.
5.6 Obsee whether the xed focus plate in the preview window is tilted or not.
If it is tilted, adjust the knob to ne-tune the camera lens so that the cross mark
is in the center of the eld of view, and the top, bottom, left, and right are as
symmetrical as possible.
Adjustment knob
left right top bottom middle
5 Calibrate camera lens
6
6 Calibration Camera Alignment
6.1 Take away the xed focus card, click on the "Camera
Alignment" window, if this inteace is closed, please click
"Camera Control" -> "Camera Alignment" -> "Camera" ->
Next
6.2 Set the engraving parameters (refer to the laser parameter table),
and set the Scale value according to the actual positioning size, see
the table below
6.3 Click Frame to see if there is a collision, if there is a
collision, you need to set a smaller Scale value, or recalibrate
the camera
6.4 Click Sta and make a positioning mark
Scale
100
150
200
200*200
300*300
400*400
mm^2
Size
7
6.5 After the engraving is complete, click the button in the red
box to move the laser to the upper position so as not to block
the engraved pattern, click Capture Image, and then click Next.
6.6 First zoom in on the pattern at position 1, double-click the cross
point, and click the cross point position in the order of numbers 1-4. If the
double-clicked cross has obvious deviation, you can click Undo Last or a
blank position, and then double-click to re-select the cross point.
6.7 Remove the cardboard when nished and click Update Overlay
Intersection
6 Calibration Camera Alignment
8
7 How to use positioning
7.1 Place the engraving or cutting material within the engraving range,
and x the focus, click "Home" to return the laser to the machine origin,
click Update Overlay, and move the engraving pattern to the position
you want to engrave.
7.3 The engraving is completed, the eect is shown below
7.2 Set the parameters of engraving and click sta
9
Inhaltsverzeichnis
Sprachen:
Andere ATOMSTACK Graveur Handbücher
ATOMSTACK
ATOMSTACK M100 Bedienungsanleitung
ATOMSTACK
ATOMSTACK A5 Bedienungsanleitung
ATOMSTACK
ATOMSTACK A5 M50 Pro Bedienungsanleitung
ATOMSTACK
ATOMSTACK A5 10W Bedienungsanleitung
ATOMSTACK
ATOMSTACK A 5 Pro Bedienungsanleitung
ATOMSTACK
ATOMSTACK Befon A5 Pro Plus Bedienungsanleitung
ATOMSTACK
ATOMSTACK A6 PRO Bedienungsanleitung
ATOMSTACK
ATOMSTACK P7 Series Bedienungsanleitung
ATOMSTACK
ATOMSTACK X20 Pro Bedienungsanleitung
ATOMSTACK
ATOMSTACK X7 Pro Series Bedienungsanleitung
