ATOMSTACK X7 Pro Series Bedienungsanleitung
ATOMSTACK X7 Pro series L a s e r
En g r a v e r I n s t a llation M a n u a l
Version: V1.0
English
Deutsche
Français
note: (The picture is for reference only, the actual product shall prevail)
Before Using the laser engraving, please read this safety guide carefully, it mentions situations that require special attention and
includes warnings of unsafe practices that can cause damage to your property or even endanger your personal safety.
1. The product belongs to Class 4 laser products, the laser system itself must meet the requirements of IEC 60825-1 latest version,
otherwise the product is prohibited to be used.
2. Our laser engraver has a protective case that prevents people from laser radiation when in place.
3. If a protective housing is equipped with an access panel which provides "walk-in" access then:
a)means shall be provided so that any person inside the protective housing can prevent activation of a laser hazard that is equivalent to
Class 3B or Class 4.
b）There is a warning device so as to provide adequate warning of emission of laser radiation equivalent to Class 3R in the wavelength
range below 400 nm and above 700 nm, or of laser radiation equivalent to Class 3B or Class 4 to any person who might be within the
protective housing.
c)Where “walk-in” access during operation is intended or reasonably foreseeable, emission of laser radiation that is equivalent to Class
3B or Class 4 while someone is present inside the protective housing of a Class 1, Class 2, or Class 3R product shall be prevented by
engineering means.
NOTE Methods to prevent human from radiation when persons are inside the protective housing can include pressure sensitive floor
mats, infrared detectors, etc.
Part 1： Security Statment Before Installation
4. The laser itself has a protective cover, the protective cover is fastened by screws. When the laser is installed on the laser engraver, the
protective cover should be checked to be reliably locked, and can not be removed in the energized state.
5. The housing of the laser engraver have an interlock function. When the housing is opened or removed, the laser can be automatically
turned off.
6. The laser engraver have an emergency stop button, which can immediately stop the output of the laser when pressed under
unexpected circumstances.
7. The laser engraver have a reset button, which can resume work under the condition of confirming safety after lifting the interlock or
emergency stop.
8. Laser engraver use physical keys, dongle, password system and other ways to manage and control, and prevent personnel without
safety training from operating such equipment.
9. Set a warning mark on any window or channel that can actively observe or passively receive laser radiation on the laser engraving
machine.
10. If the laser burns the skin or eyes, please go to a nearby hospital for examination and treatment immediately.
Laser Light can hurt the human eyes and skin. Do not expose the eye or skin to laser light directly. This Laser product has an optical
lens and emits a collimated laser beam. The light emitted by the product, whether it is direct or reflected, is very harmful. Because it can
propagate a long distance while maintaining high optical density. When handling the product,you must wear appropriate
goggles(OD5+) to protect eyes from laser light including reflected and stray light. The reflected and stray light spilling into an
unintended area should be attenuated and/or absorbed.
2.1 Laser safety
We installed a laser shield on the laser, the shield can largely filter out the diffuse reflection of the laser spot. However, when using laser
engraving machine, it is recommended that you should wear laser protective glasses. Avoid skin exposure to type 4 laser beams,
especially at the closed distance.Teenagers must have parental supervision in the process of using it. Do not touch the laser engraving
module when the machine is activated.
2.2 Fire safety
Because cutting burns off the substrate, a high-intensity laser beam generates extremely high temperatures and a lot of heat.Certain
materials can catch fire during cutting, creating gases and fumes inside the equipment.A small flame usually appears here when a laser
beam hits the material.It will move with the laser and will not stay lit when the laser passes by. Do not leave the machine unattended
during the engraving process. After use, be sure to clean up the debris, debris and flammable materials in the laser cutting machine.
Always keep an available fire extinguisher nearby to ensure safety.When laser engraving machines are used, smoke, vapour, particles,
and potentially highly toxic materials (plastics and other combustible materials) are produced from the material.These fumes or air
pollutants can be hazardous to health.
Part 2：User Security Statement
2.3 Material safety
Do not engrave materials with unknown properties. Materials Recommended:Wood, bamboo, leather, plastic, fabric, paper, opaque
acrylic, glass.Materials not recommended:Metal, precious stones, transparent materials, reflective materials etc.
2.4 Use Safety
Use the engraver only in horizontal position and ensure that it has been securely fixed to prevent fires caused by accidental shifting or
dropping from the workbench during work.It is forbidden to point the laser to people, animals or any combustible object, whether it is
in working condition or not.
2.5 Powersafety
Topreventaccidentaldisasterssuchasfireandelectricshock,the LaserEngraverprovidesapoweradapterwitha groundwire.When
using the laser engraving machine, insert the power plug into a power socket with a ground wire withaground wirewhenusing
theLaserEngraver.
2.6 Environment safety
When installing engraving and cutting equipment, please make sure that the workplace must be cleaned up, and there should be no
flammable and explosive materials around the equipment. A metal plate must be placed under the bottom when engraving or cutting.
Part 3: Disclaimer and warning
Thisproductisnotatoyandisnotsuitableforpeopleunder15.Donotallowchildrentotouchthelaser
module.Pleasebecarefulwhenoperatinginsceneswithchildren.
Thisproductisalaser module,visithttp://www.atomstack3d.com/laserengraverdownloadto get the
complete"usermanual"andthelatestinstructionsandwarnings.ShenzhenAtomStackTechnologiesCo.,Ltd.(Atomstack)reservestherightto
updatethisDisclaimerandSafeOperationGuidelines.
Pleasebesuretoreadthisdocumentcarefullybeforeusingtheproducttounderstandyourlegalrights,responsibilitiesandsafetyinstructions;
Otherwise,itmaybringpropertyloss,safetyaccidentandhiddendangerofpersonalsafety.Onceyouusethisproduct,youshallbedeemedto
haveunderstood,andacceptedalltermsandcontentsofthisdocument.Userundertakestoberesponsibleforhisorheractionsandallconse
quencesarisingtherefrom.UseragreestousetheProductonlyforlegitimatepurposesandagreestotheentiretermsandcontentsofthisdocu
mentandanyrelevantpoliciesorguidelinesthatAtomStackmayestablish.
You understand and agree that AtomStack may not be able to provide you with the cause of the damage or accident and provide you with
AtomStack's after-sale service unless you provide the original engraving or cutting files, engraving software configuration parameters used,
operating system information, video of the engraving or cutting process, and operational steps prior to the occurrence of a problem or failure.
AtomStackisnotliableforanyandalllossesarisingfromtheuser'sfailuretousetheproductinaccordancewiththismanual,Without the
guidance of the company's technical personnel, users are prohibited from disassembling the machine by themselves. If this behavior occurs, the
loss caused by the user shall be borne by the user.
Atomstackhastheultimaterighttointerpretthedocument,subjecttolegalcompliance.Atomstackreservestherighttoupdate,modify,orter
minatetheTermswithoutpriornotice.
Logo side up
Screw:
M5*25
Gap side
outwarder
1
1
33
3
Y
X
2M5-6
2
S t e p 2
The guide rail passes through the middle of the 3
rollers. Loosen the distance between the upper and
lower guide wheels appropriately.
3
4
1
2
3 3
Tighten the T nut and cut off
the excess belt.
group 2
installation hole
slide block
torx handle
Alongside
Figure 3
Figure 4
Fasten
Screw
Figure 2
Figure 1
S t e p 3
S t e p 1
S t e p 4
Engraving or cutting scope
0~65mm
Engraving or cutting
scope 0~45mm
Engraving or cutting scope
0~85mm
Group 3rd
Group 2nd
Group 1st
P a r t 4 ：I n s t a l l a t i o n S t e p s
YX
Y-axis
limiter
TIPS：How to determine the tightness of eccentric nuts?
Under the condition of ensuring that the bracket does not shake, you can lift one
end of the machine to an angle of 45 degrees with the horizontal plane, and release
the X-axis or Y-axis bracket from a high place. If the bracket can slide at a constant
speed to the end, the tightness is suitable.
S t e p 5
Use a wrench to
turn the eccentric
nut to adjust the
tightness of the
guide wheel and
the guide rail
Partial
enlarged
view
1
3
S t e p 6
S t e p 7
Installation Manual:
1. As shown in the picture, place the cutting pad under the
engraved/cut object
2. As shown in the figure, the cutting pad should be placed to
cover the working area as far as possible
Part 5：Control box
description
①
②③
④
⑤
⑥
1.Emergency stop switch：In case of emergencies, the machine will immediately stop working when you press it. When you
need to unlock it, turn the button clockwise to restart the engraver.
2.Power socket: DC 12V power supply.
3.USB interface: control the engraver on the computer with connecting to the computer through a USB cable.
4. Power switch: control the power on and off.
5. TF card slot: here to insert the TF card.
6. Reset switch: When an emergency occurs or the machine is stuck, press the reset button to restart the engraver.
Part 6：Instructions for use of the display
LaserGRBL exports nc
format, Lightburn exports
gc format
Insert SD card Click Cavre to
enter the SD card
file list
Press the power
button to enter the
home page of the
display
Select the file to be
engraved and move
the laser to the position
to be engraved
Laser fixed focus
method: use a fixed
focus lens below the
laser to determine the
focal length
Select the number of
times you want to
engrave/cut, start
engraving/cutting
Click the position
button to determine
the origin of the laser
Finish carving
Click the frame button
to confirm the
engraving range
Click the
button to start carving
During the engraving
process, the engraving
speed and energy can
be adjusted. If there is
an abnormal situation,
you can press the pause
or stop function key
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere ATOMSTACK Graveur Handbücher
ATOMSTACK
ATOMSTACK X20 Pro Bedienungsanleitung
ATOMSTACK
ATOMSTACK MAKER AC1 Bedienungsanleitung
ATOMSTACK
ATOMSTACK A5 M50 Pro Bedienungsanleitung
ATOMSTACK
ATOMSTACK A5 Bedienungsanleitung
ATOMSTACK
ATOMSTACK A5 10W Bedienungsanleitung
ATOMSTACK
ATOMSTACK M100 Bedienungsanleitung
ATOMSTACK
ATOMSTACK Befon A5 Pro Plus Bedienungsanleitung
ATOMSTACK
ATOMSTACK A 5 Pro Bedienungsanleitung
ATOMSTACK
ATOMSTACK P7 Series Bedienungsanleitung
ATOMSTACK
ATOMSTACK A6 PRO Bedienungsanleitung
