Audiovox XM SRXM-001 Bedienungsanleitung

FOR USE WITH THE RADIO RECEIVER

UNIT (RRU) MODEL XM-RCV

INSTALLATION MANUAL

ELECTRONICS COR

999.audiovox.com

For Customer Service

Visit Our Website At

Product Information, Photos,

FAQ’s Owner’s Manuals

XM®SATELLITE DIGITAL AUDIO

RECEIVER SYSTEM MODEL SRXM-001

The Audiovox Electronics XM®Satellite Digital Audio Control And Receiver System (Model

SRXM-001) was developed to allow the user to listen to a huge selection of programming

supplied by a subscription to XM®Radio. (XM®-compatible antenna also required).

The Audiovox Electronics XM®Satellite Digital Audio Control And Receiver System is easily

installed using the installation instructions herein, and is designed to work with the user’s

existing car stereo system through an unused FM frequency or the auxiliary audio inputs.

The programming and use of this system is described in detail in the supplied Owner’s

Manual.

The Audiovox Electronics XM®Satellite Digital Audio Control and Receiver System comes

with a satellite RADIO RECEIVER UNIT (RRU), a SATELLITE SYSTEM CONTROL UNIT

(SCU), and a FM MODULATOR/CONTROL INTERFACE unit that allows the user to select

an exact XM®Radio channel on the easy to read display. The controller is compact, pleas-

antly designed and can be mounted in the cab of the vehicle in numerous ways. This Instal-

lation Guide depicts typical installation scenarios.

It is important that the installer reads and understands all of the installation procedures for

each of the components to be installed, either supplied with the Audiovox Electronics XM

Satellite Digital Audio Control and Receiver System (Model SRXM-001) or equipment that

is to be installed in conjunction with the system such as the XM®Antenna.

The Audiovox Electronics XM®Satellite Digital Audio Control and Receiver System (Model

SRXM-001) comes with a 36 month limited warranty (see the back cover of the owner’s

manual for details)

INTRODUCTION

TRADEMARKS

www.pro-fit-intl.com

Other product names mentioned in this manual may be trademarks or registered trademarks

of their respective companies and are hereby acknowledged.

INSTALLATIONandWIRINGPRECAUTIONS

1. To prevent a short-circuit, Be sure to turn off the ignition and remove the negative (-)

battery cable, prior to installation. Connect power wires last.

NOTE: If the SRXM-001 System is to be installed in a car that is equipped with an on-board

drive or navigation computer, do not disconnect the battery cable. If the cable is discon-

nected, the computer memory may be lost. Under these conditions, use extra caution during

installation not to cause a short circuit.

2. Do not install the unit in the following locations:

Locations exposed to direct sunlight.

Where hot air is discharged from the car heater.

Inareassubjecttoextremetemperatures.

3. Incorrectinstallationmaycause damagetothesystem. Mounttheunit firmlyinplace, using

the supplied brackets and screws.

4. Be careful not to damage the car wiring.

5. Be sure to use the supplied screws and washers.

6. Be careful not to snag any wires when tightening screws.

Satellite Radio

Wireless Remote

Control Model

#SAT-RC

Self-tapping Screws (5mm x 15mm), with

Flat Washers and Lock Washers

(Used to mount RRU to mounting surface)

FMModulatorControl

Interface Wire Harness

1 pc.

(P/O SAT-COM)

PhillipsRoundHead

Screw (4mm x 8mm)

w/ External Tooth Washer

(Used to mount SCU to mounting

surface)

4 pcs. each

(P/O XM-RCV)

INSTALLATION PARTS

SRXM-001 MAIN SYSTEM COMPONENTS

(NOTE: Components are not drawn to scale.)

PACKING LIST

PhillipsRoundHead

Screw (4mm x 8mm)

(Used to mount

bracket to RRU)

4 pc.

(P/O XM-RCV)

RRU Mounting

Brackets

2 pc.

(P/O XM-RCV)

Din Cable, 13- pin

(6 Meter)

To connect the RRU to the FM Modula-

tor / Control Interface

1 pc.

(P/O XM-RCV)

AUDIO OUT

LR DIN OUTSAT.TER.

AUDIO OX

SATELLITESYSTEMCONTROL

UNIT(SCU)

Model # SAT-COM

1 pc.

FM MODULATOR /

CONTROL INTERFACE

1 pc.

(P/O SAT-COM)

RADIO RECEIVER UNIT (RRU)

Model # XM-RCV

1 pc.

PhillipsRound

Head. Screw

(4mm x 12mm)

(Used to mount FM MOD

to mounting surface)

4 pc.

(P/O SAT-COM)

SFT

AUDIO OX

Hook & Loop

AdhesiveTape

1 cut set.

(P/O SAT-COM)

Quick

Reference

Card

1 pc.

(P/O SAT-COM)

Owner's

Manual

1 pc.

(P/O SAT-COM)

SUPPLIED

ACCESSORIES

OPTIONAL

ACCESSORIES

Trim Ring,

Satellite Control

Model #SAT-PF

4 pcs. each

(P/O XM-RCV)

RCAtoRCA Cable

(6 Meter)

To connect the RRU to the FM Modula-

tor / Control Interface

1 pc.

(P/O XM-RCV)

RLTO RRUTO SCU

ANT.

POWER

TO CAR

TO RADIO

ANT.

SATELLITE RADIO RF MODULATOR

AUDIO OX

SFT

SATELL ITE RADIO RF MODULATOR

TO SCU

AUDIO OX

ANT.

TO RADIO

TO CAR

ANT.

RLTO RRU

PO WER

AUDIO OX

TER. SAT. DIN OUT

AUDIO OUT

R L

TYPICAL FM MODULATED SYSTEM

INSTALLATION

NOTE:“A”To Satellite Radio Antenna

(Soldseparately)

*Green=Terrestrial connection

*Yellow= Satellite connection

NOTE: “B” RCA to RCA Cable (supplied

withsystem) used to connect the RRU Audio

Ouput tothe RF Mododulator Audio Input.

IMPORTANT - Some vehicles use a special dual antenna “Diversity" system.

If the vehicle into which this system is being installed has this type of antenna

system, the antenna cable will not fit the socket on the FM modulator. Use

of the SRXM-001 system with “Diversity" systems is not recommended. You

may also find some cars have an antenna plug that is too small to mate with

the socket on the FM modulator. If this is the case, call Audiovox’s Toll-Free

Assistance for a special adaptor. This adaptor can also be purchased at most

car stereo installation centers.

NOTE: “C” Before routing the Din Cable to

connecttheFM Modulator to the RRU,

observethe color code to avoid any

unnecessaryre-work. The Gray connector is

matchedto the FM Modulator and the Black

connectorismatched to the RRU.

TYPICAL AUXILLARY AUDIO SYSTEM

INSTALLATION

ANT.

TO CAR

AUDIO OX

TER. SA T. L

AUDIO OUT

RDIN OUT

TO RADIO

ANT.

PO WE R

TO RR U

AUDIO OX

SATELLITE RADIO RF MODULATOR

LTO SCU

AUDIO OX

SFT

NOTE:“A”To Satellite Radio Antenna

(Soldseparately)

*Green=Terrestrial connection

*Yellow= Satellite connection

NOTE: “B” RCA to RCA Cable (supplied

withsystem) used to connect the RRU Audio

Ouput tothe Radio Reciever Auxilary Input.

-or-

RCAto 1/8” Stereo Plug Cable (not supplied

withsystem) used to connect the RRU Audio

Outputto the Radio Reciever AuxilaryInput.

IMPORTANT - Some vehicles use a special dual antenna “Diversity" system.

If the vehicle into which this system is being installed has this type of antenna

system, the antenna cable will not fit the socket on the FM modulator. Use

of the SRXM-001 system with “Diversity" systems is not recommended. You

may also find some cars have an antenna plug that is too small to mate with

the socket on the FM modulator. If this is the case, call Audiovox’s Toll-Free

Assistance for a special adaptor. This adaptor can also be purchased at most

car stereo installation centers.

NOTE: “C” Before routing the Din Cable to

connecttheFM Modulator to the RRU,

observethe color code to avoid any

unnecessaryre-work. The Gray connector is

matchedto the FM Modulator and the Black

connectorismatched to the RRU.

TYPICAL FM MODULATED INSTALLATION for

SRXM-001 SYSTEM COMPONENT LAYOUT

MOUNTING THE FM MODULATOR

Install the FM Modulator to the mounting surface with the

self-tapping screws (4mm x 12mm).

Self-Tapping

PhillipsHead

Screw

Ground (BLACK)

Attach this wire to the chassis of the car. Be

sure that the surface is free of paint and is

not rusty. If a proper ground connection is

not made, the SRXM-001 System may not

operate correctly and stray noise may be

picked up by the unit.

FMModulator

FMRadio

DINCable

To FM Radio

Antenna input

RRU

SCU

From Existing

Vehicle Antenna

Satellite Radio

Antenna

(Purchased

Separately)

+12V Battery

(YELLOW)

Connect this wire to

a terminal which is

always energized.

+12V Accessory / Ignition (RED)

Connect this wire to a terminal which

is energized when the ignition switch

is turned to the "ON" or "ACCESSORY"

position.

FilterBox

& Fuses

13-Pin

DIN Cable

RCAtoRCA

Cable

PROCEDURE for HORIZONTAL INSTALLATION of the RRU

SYSTEM INSTALLATION

RADIORECEIVERUNIT(RRU)

2. Determine the mounting location and drill 4x 1/8” (4mm) mounting holes.

NOTE:If mounting surface is carpeted, use caution when drilling holes to prevent drill bit from

catching on carpet. Cut holes in carpet before drilling into subsurface.

1. Attach the mounting brackets to each side of the RRU, using the 4 Phillips Round Head

Screws (4mm x 8mm).

Mount the unit in place, using 4 Self-tapping Screws (5mm x 15mm), w/Flat Washers and

Lock Washers. Use RTV (silicone sealer) on screw threads or around the holes to prevent

moistureintrusion.

Bracket

Phillips Head Screws (4mm x

8mm) used in 4 places

RRU

Bracket

Self-tapping Screw

(5mm x 15mm), w/Flat

Washers and Lockwashers

used in 4 places

Carpet

WARNING

Never mount the unit near the fuel tank.

Carpet

4x 1/8” (4mm)

mounting holes

Attach a mounting bracket to each side of the RRU, using the 4 Phillips Round Head

Screws (4mm x 8mm).

Mountthe unitinplace,using4 Self-tapping Screws(5mmx 15mm),w/FlatWashersandLock

Washers. UseRTV (siliconesealer)on screwthreadsoraroundthe holestoprevent moisture

intrusion.

PROCEDURE for VERTICAL INSTALLATION of the RRU

2. Determine the mounting location and drill 4 x 1/8” (4mm) mounting holes.

NOTE: Ifmountingsurface is carpeted,usecautionwhen drilling holestopreventdrill bit from

catching on carpet. Cut holes in carpet before drilling into subsurface.

Bracket

RRU

Phillips Head Screws (4mm x

8mm) used in 4 places

RRU

Bracket

Carpet

Self-tapping Screw

(5mm x 15mm), w/Flat

Washers and Lockwashers

used in 4 places

WARNING

Never mount the unit near the fuel tank.

Carpet

4x 1/8” (4mm)

mounting holes

Determine the mounting location and drill four 4mm mounting holes.

3. Mount the unit in place, using 4 Self-tapping Screws (5mm x 15mm), w/Flat Washers and

Lock Washers.

1. Attach the mounting brackets to each side of the RRU, using the 4 Phillips Round Head

Screws (4mm x 8mm).

PROCEDURE for the MOUNTING of the RRU UNDER THE REAR DECK

Bracket

Phillips Head Screws

used in 4 places (4mm x 8mm)

Underside of

Rear Deck

4x 1/8” (4mm)

mounting holes

(4 places)

Self-tapping Screw

(5mm x 15mm), w/Flat

Washers and Lockwashers

used in 4 places

Rear

Deck

Inhaltsverzeichnis

Andere Audiovox Empfänger Handbücher

Audiovox

Audiovox GMRS-2000 Bedienungsanleitung

Audiovox

Audiovox AV1510D Bedienungsanleitung

Audiovox

Audiovox Xpress XM Bedienungsanleitung

Audiovox

Audiovox Phase Linear UV7 Bedienungsanleitung

Audiovox

Audiovox SIRIUS SRSIR-001 Bedienungsanleitung

Audiovox

Audiovox HDP100 - Acoustic Research HD Powerlink Bedienungsanleitung

Audiovox

Audiovox SIRIUS SRSIR-001 Bedienungsanleitung

Audiovox

Audiovox Xpress XMB10 Bedienungsanleitung

Audiovox

Audiovox SIRIUS CE1000SR Bedienungsanleitung

Audiovox

Audiovox VXE 7020 NAV Bedienungsanleitung

Audiovox

Audiovox VME 9425 Bedienungsanleitung

Audiovox

Audiovox SIRIUS CE1000SR Bedienungsanleitung

Audiovox

Audiovox GMRS-2000 Bedienungsanleitung

Audiovox

Audiovox XMCK5 - Car XpressEZ Satellite Radio... Bedienungsanleitung

Audiovox

Audiovox UV 8 Bedienungsanleitung

Audiovox

Audiovox HDP100 - Acoustic Research HD Powerlink Bedienungsanleitung

Audiovox

Audiovox VME 8013 - Bedienungsanleitung

Audiovox

Audiovox Xpress XMH10 Bedienungsanleitung

Audiovox

Audiovox 128-7376 Bedienungsanleitung

Audiovox

Audiovox XMRVRFM002 - Commander MT XM Radio Tuner Bedienungsanleitung

Audiovox

Audiovox iHD-P01 Bedienungsanleitung

Audiovox

Audiovox XMCK10AP - XM Radio Tuner Bedienungsanleitung

Audiovox

Audiovox Sirius SRSIR-001FM Bedienungsanleitung

Audiovox

Audiovox XMH10 Home Cradle Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung