Audiovox Pursuit OE3-FT3 Betriebsanleitung

TRANSMITTER PROGRAMMING GUIDE

Model: OE3-FT3

Thetransmittersincludedwiththesecuritysystemhavebeenpre-programmedatthe

factory, with each button pre-assigned to control a specific function of the security

system. Although the security system in the vehicle has either a 3, 4 or 5 channel

receiver, depending on the model, the transmitters included with the system are

capableoftransmitting7distinct signals. Thisallowsyou toprogrameach transmitter

to more than one vehicle in two car families, and also allows you to change which

button(s) control certain functions of the system.

(Example:Transmitterchannel5canbeprogrammedtoactivateReceiverchannel2.)

Refer to the chart below for access to each of the transmitter channels, and for the

standard factory button assignments.

Some of the more common accessories for these additional channels are;

AS 9554 Remote Garage Door Interface

AS 9075 Remote car starter

AS 9153 Remote window roll up

AS 9256 Remote trunk release relay

TRANSMITTER SYSTEM RECEIVER

CHANNEL BUTTON CHANNEL FUNCTION

Remote Arm

1 1 Remote Emergency Panic

Remote Door Lock

Remote Disarm

2 2 Remote Emergency Panic

Remote Door Unlock/Unlock 2

4& 4

5& 5

6 & 6 RF Channel For Options

7 7 RF Channel For Options

All 3

Buttons

Single Push Pulsed Output for Optional Accessory

Or Double Push For Additional Optional Accessory

Single Push Pulsed Output for Optional Accessory

Or Push And Hold For Extended Output

Single Push Pulsed Output for Optional Accessory

Or Push And Hold For Extended Output

PROGRAMMING THE TRANSMITTERS

Itisimportanttorememberthatduringprogramming, each individual step of the

procedure must be executed within 15 seconds of the previous step.

Whenthe15secondtimelimit is allowed to expire,thesystemwillautomatically

terminatetheprogrammingmode.Thisisindicatedbyalongchirpfromthesiren.

Additionally, the system will store codes from up to four different transmitters.

If a 5th transmitter is programmed to any receiver channel, then the first

transmitter programmed to that channel will be erased from the system's

memory.

To Program replacement or additional transmitters:

1. Enter the vehicle, and turn the ignition key to the "on" position.

2. Press and release the valet push-button switch 3 times.

3. The dash LED will flash one time, and the sounding device will beep one

time, indicating the system is ready to accept programming for receiver's

Lock channel 1.

4. Press and hold the Lock transmitter button until the sounding device emits

a long beep, indicating the signal has been stored into memory.

5. If you have additional transmitters (up to 4) that need to be programmed,

repeat step 4 for each transmitter.

6. Press and release the valet push-button switch once.

7. The dash LED will flash two times, and the sounding device will beep two

times, indicating the system is ready to accept programming for receiver's

Unlock channel 2.

8. PressandholdtheUnlocktransmitterbuttonuntilthesoundingdeviceemits

a long beep, indicating the signal has been stored into memory.

9. If you have additional transmitters (up to 4) that need to be programmed,

repeat step 8 for each transmitter.

10. Press and release the valet push-button switch once.

11. ThedashLEDwillflashthreetimes,andthesoundingdevicewillbeepthree

times, indicating the system is ready to accept programming for receiver's

channel 3.

12. Press and hold the selected Option transmitter button until the sounding

deviceemitsalongbeep,indicatingthesignalhasbeenstoredintomemory.

13. If you have additional transmitters (up to 4) that need to be programmed,

repeat step 12 for each transmitter.

14. Press and release the valet push-button switch once.

15. The dash LED will flash four times, and the sounding device will beep four

times, indicating the system is ready to accept programming for receiver's

channel 4.

16. Press and hold any button combination as shown on the front cover of this

guideuntilthesounding device emits alongbeep,indicatingthesignalhas

been stored into memory.

17. If you have additional transmitters (up to 4) that need to be programmed,

repeat step 16 for each transmitter.

18. Press and release the valet push-button switch once.

19. The dash LED will flash four times, and the sounding device will beep four

times, indicating the system is ready to accept programming for receiver's

channel 5.

20. Pressandholdanyunusedbuttoncombinationasshownonthefrontcover

of this guide until the sounding device emits a long beep, indicating the

signal has been stored into memory.

21. If you have additional transmitters (up to 4) that need to be programmed,

repeat step 20 for each transmitter.

22. Turn the ignition key off. The sounding device will emit one short beep

followed by one long beep indicating the system has terminated the

program mode.

TRANSMITTERBATTERY REPLACEMENT

You will notice a decrease in transmitter range as the battery condition

deteriorates.Transmitterbatteryreplacementisrecommendedatleastevery10

to 12 months, depending upon how frequently the transmitter is used.

The transmitter has a small red LED visible through the case. This LED can be

usedtoindicatebatterycondition.IftheLEDdoesnotilluminate,thenthebattery

is discharged, and must be replaced.

To replace the transmitter battery,

1. Remove the small phillips head screws from the bottom cover of the

transmitter.

2. Carefully unsnap the top cover of the transmitter from the bottom cover.

3. Remove the discharged battery, making

note of the location of the + and - contacts,

andreplacewithanewtypeGP27A12volt

battery.

4. Replace the transmitter cover, taking care

not to damage the LED or switches on the

circuit board, and secure with the small

phillips head screw.

ORDER FORM FOR 3 BUTTON TRANSMITTER

MODEL NO. PRO-OE3FT3

IMPORTANT:Tohelpusexpediteyourorder,pleaseprintalloftheinformation

legibly, and mail this form and your payment according to the instructions

below.

Note: Order Pad # 17 if your unit has red colored Lock/Unlock pads.

Order Pad # 18 if your unit has blue colored Lock/Unlock pads.

1. Name : ____________________________________________________

Address: _____________________________________________________

City : _____________________ State : _______ Zip Code : ____________

2.TelephoneNumber:(_______)_________________________________

3. Enter the total number of transmitters required here : ________________

4. List model number of your actual transmitter pad as shown on page

4 of this manual:

5. The cost per transmitter is $ 65.00.

6. Enter the total amount enclosed here : ____________________________

( New York state residents must include the appropriate sales tax.)

7. Method of payment; check one of the boxes below.

qMastercard qVisa qCheck or money order * ( do not send cash )

* Make checks payable to Audiovox Corporation

8. Credit Card Number : ________________________________________

9. Credit Card Expiration Date : _____________________

Credit card purchasers can order additional or replacement

transmittersbyphone.Simplydial1-800-645 - 4994, and follow

the instructions from the operator interface.

10. Mail this form, and your check, to ;

(

128-5759

Audiovox Electronics Corp., 150 Marcus Blvd. Hauppauge, N.Y., 11788

Attn.:TRANSMITTERDEPARTMENT

Inhaltsverzeichnis

Andere Audiovox Sender Handbücher

Audiovox

Audiovox PRO94BT3 Betriebsanleitung

Audiovox

Audiovox Auto Security SS91 Betriebsanleitung

Audiovox

Audiovox Prestige 101BP Betriebsanleitung

Audiovox

Audiovox AA923-AA94BT Betriebsanleitung

Audiovox

Audiovox 128-5971 Montageanleitung

Audiovox

Audiovox Pursuit 095BPr Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE2 Betriebsanleitung

Audiovox

Audiovox PRO92BTINT Betriebsanleitung

Audiovox

Audiovox PRO-OE3B370 Betriebsanleitung

Audiovox

Audiovox ACA300 Bedienungsanleitung

Audiovox

Audiovox AVX01BT3CL3 Betriebsanleitung

Audiovox

Audiovox A1BTX Betriebsanleitung

Audiovox

Audiovox PurSuit 09XR1Pr Betriebsanleitung

Audiovox

Audiovox PRO94BT2 Betriebsanleitung

Audiovox

Audiovox PurSuit 091BPr Betriebsanleitung

Audiovox

Audiovox S1BTXA Betriebsanleitung

Audiovox

Audiovox Prestige APS-92BT-CL Fehlerbehebungshandbuch

Audiovox

Audiovox Pursuit 095BPr Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE3 Betriebsanleitung

Audiovox

Audiovox AUTO SECURITY Prestige OE3B4 Betriebsanleitung

Audiovox

Audiovox Pursuit Series Bedienungsanleitung

Audiovox

Audiovox PRO-OE3C Fehlerbehebungshandbuch

Audiovox

Audiovox PRO-94FR Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-OE4 Betriebsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung