Auto Page RF-425LCD Bedienungsanleitung

RF-425LCD

PROFESSIONAL VEHICLE SECURITY SYSTEM

OPERATION MANUAL

THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY

TRANSMITTER OPERATION:

Transmitter

Button System Function Remark

Lock Doors & Arm System

Panic function Press and Hold for 3 seconds

Car Locator Under armed mode

Arm and Delete The 2 Stage Shock

Sensor Presstwice within3 seconds

+ Silent Arming / Disarming Ignition in "off" position.

Unlock Doors & Disarm System

Two Steps Door Unlock & Disarm

System Presstwice within3 seconds.

Trunk Release (Channel 2)

Press and Hold for 2 seconds

Passive Arming By-pass While the system Disarmed.

Silent Arming/ Disarming

+ 3rd Channel Press buttons together

+ 4th Channel Press buttons together

Switching code For 2nd

Car

Operation.For regular remote transmitter Only

ACTIVE ARMING –LOCK & ARM:

1. Press button on transmitter.

2. The siren will chirp once and parking light will flash once indicating that the system is now

armed. The vehicle doors will lock upon arming when interfaced with the security system.

Note: Defective sensor reminder:

If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.

SystemArm

DoorAjar

Trunk / Hood Ajar

AJAR WARNING:

If the siren sounds 3

chirps, then you have

left a door, trunk, or

hood lid ajar.

SILENT ARMING / DISARMING: Press the button on the transmitter to arm or disarm your

security system with no chirp sound heard; arm / disarm confirmation will be through the vehicles

parking lights only.

SHOCK SENSOR / OPTIONAL SENSOR BY-PASS:

Press the button on the transmitter twice within 3 seconds will arm the security system, by-

pass the shock sensor or the optional sensor connected to 4 pin plug. The system will chirp one

additional time to confirm the sensor bypass mode was activated. The sensor bypass feature is

programmed to activate for one arming cycle only. The security system will return to normal

operation during the next arming cycle.

PASSIVE ARMING:

Active arming / disarming is controlling your security system via the remote transmitter. This

security system is equipped with an optional Passive Arming feature, which allows the security

system to arm 30 seconds after the last door is closed. Operation is as follows.

1. Turn the ignition to the “OFF” position and exit the vehicle.

2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you

reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing

again once all vehicle entrances are closed.

3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren

will chirp [1] time and the parking lights will flash [1] time.

PASSIVE DOOR LOCKING:

The vehicle doors will automatically lock after passive arming cycle has been completed.

PASSIVE ARMING BY-PASS: While the system disarmed, press the buttons twice, the

security will respond with [1] chirp and LED will turn “ON”. The security system will remain in

this temporarily state for as long as you wish. To exit passive by-pass, press the or

button and the system will return to normal status.

ACTIVE DISARMING –UNLOCK & DISARM:

1. Press the button on the transmitter.

2. The siren will chirp twice and parking lights will flash twice to indicate that the security system

is now disarmed. The vehicle doors will unlock and disarm when interfaced with the security

system.

System

Disarm

Trunk/Hood

Trigger

Doors

Trigger

Shock Sensor

Trigger

Ignition

Trigger

Clear the Flash Icon and Melody Sound: Cycle Ignition then press the

button first, within 3 seconds press and buttons at the same time.It

will

clear theflash icon and melody sound on the LCD screen transceiver

TAMPER DISARMING: If the alarm is triggered; upon disarming of the system, the siren will

chirp 4 times and parking lights will flash 3 times.

PATHWAY ILLUMINATION: This feature turns the parking light “ON” for 30 seconds upon a

unlock signal and for 10 seconds upon the lock signal if programmed.

TWO STEP DOOR UNLOCK: This feature will independently unlock the driver’s door only when

disarming the security system. Pushing the button on the transmitter a second time within 3

seconds will unlock the entire vehicle. (Additional installation required)

AUTOMATIC RE-ARM:If this feature is selected, the security system will automatically re-arm

itself 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door

is opened before the 60 seconds timer has elapsed.

DISARMING WITHOUT A TRANSMITTER

The Override function may be used ifthe remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)

2. Within 10 seconds push and release the valet switch

The alarm will stop sounding and enter the disarm mode. You can now start and operate the

vehicle normally.

VALET MODE:

The valet switch allows you to temporarily bypass all alarm function, eliminating the need to

hand your transmitter to parking attendants or garage mechanics. When the system is in valet

mode, all alarm functions are bypassed, however, the remote panic feature and remote door

locks will remain operational.

EnterValetMode:

1. From the disarmed condition, turn the

ignition to “ON” position.

2. Push and hold valet switch for 2 seconds

until the LED turns on. The LED wills

remain on as long as the system is in

'valet mode'.

Remote Door Lock

Remote Door Unlock

Exit Valet Mode:

1. Return to normal operation, turn ignition 'ON'.

2. Push and hold valet switch for 2 seconds; the LED will turn off indicating the system is exiting

the valet mode.

POWER ON MEMORY:

This security system is equipped with circuitry that will allow the unit to remember its alarm state

if the power is lost and then reconnected.

PANIC FUNCTION:

The transmitter can be used as a remote panic switch to manually trigger the alarm in case of

emergency.

1. Press and hold the button on the transmitter for 3 seconds. The alarm will immediately

sound.

2. During panic mode, the normal function of this transmitter button will be suspended. The

and buttons can be used to lock and unlock the doors (if the option is installed), however

once the button is pressed, the vehicle’s starter disable device, (where installed) will be

enable allowing the vehicle to start.

3. To stop the alarm, press and hold the or or button on the transmitter for 3 seconds.

Also if the button is pressed and released, the panic mode will be turned off immediately.

4. If the button is not pressed, the alarm will automatically stop after 30 seconds.

TRIGGER THE SYSTEM

When armed, your vehicle is protected as follows:

1. Light impacts will triggerthewarn-away signal. A long chirp from siren/horn.

2. Heavy impacts / Doors open / Hood open / Trunk open / Turning on the ignition switch-All will

trigger the programmed sequence.

The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren and

parking lights will turn on to alert of an intrusion for 30 seconds. Then the siren will stop and

automatically reset and re-arm. If any the sensors or detectors are still active, the alarm system

will sound a maximum of three-30secondcycles.

Trunk/Hood

Trigger

Doors

Trigger

Shock

Sensor Trigger

Ignition

Trigger

Warn

away Trigger

Clear the Flash Icon and Melody Sound:

Cycle ignition then press the

button first, within 3 seconds press and buttons at t

he same

time.It will clear the flash icon and melody sound on the LCD screen

transceiver

NOISE ABATEMENT CIRCUIT:

Your system has “Noise Abatement Circuit”. It prevents annoying repetitive trigger sequences

due to faulty door pin switches or environmental condition such as thunder, jackhammers, airport

noise, etc. Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each

time, the same sensor or switch is triggering the alarm. “Noise Abatement Circuit” will interpret

this pattern of triggers as false alarm. After the fifth trigger, “Noise Abatement Circuit” ignores, or

bypasses, that sensor or switch until the other sensor or switch is trigger.

“Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an

open door for three full cycles, the doors will be bypassed until the trigger ceases.

DRIVER PAGING (For two-way transmitter operation only)

It is useful in the event that someone wants to page the driver of the parked vehicle. With the

ignition switch in the “off” condition, press the button on the window mount antenna once to

page the driver, one chirp sound shall be emitted from the vehicle and the paging melody

continues sounding from your Remote LCD Transmitter and “ ” indication flashes on the LCD

screen.

IGNITION CONTROL DOOR LOCKS.

If the vehicle’s door locks have been interfaced to the security system, the system will

automatically lock the vehicle's doors when the ignition is turned “ON” and /or unlock the

vehicle’s doors when the ignition is turned “OFF”.

TRUNK RELEASE.

Press and hold button on transmitter for two seconds to remote control the trunk release or

other electric devices.

CHANNEL 3 CONTROL OUTPUT

Press the + buttons on the transmitter to active Channel 3 function

CHANNEL 4 CONTROL OUTPUT

Press the + buttons on the transmitter to active Channel 4 function.

CAR LOCATOR

Under Armed mode, press the button on the transmitter to active car locator function.

The siren will chirp 6 times. The parking light will flash 12 times, for you to easily locate

yourcar.

DOME LIGHT CONVENIENCE DELAY & SUPERVISION

The alarm with a unique feature which will turn on your vehicle dome light as following:

1. Upon disarming, the interior lights will remain on for 30 seconds.

2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.

Note:Turn ON the ignition switch or arm the alarm will turn off the dome light.

(Additional installation required)

LCD REMOTE CONTROL TRANSMITTER:XT-43 LCD

Note: If the system is interfered by strongerradio

frequency around, sources of high voltage electric

power or such Obstacles like tall buildings and so

on, the transmission range may get shorter as the

system uses low out put powered frequency.

BATTERY REPLACEMENT:

A 1.5V type AAA Alkaline battery powers the

Remote Transmitter. When the power of the

battery weakens a icon shall be displayed

on the LCD screen. When the old battery is

replaced to new one, there will be beep sounds

indicate the power is up.

Note: Press the button two times when the

battery compartment is empty, and then insert

thenewbattery.

THE REMORE LCD ICONS WITH FUNCTION:

DoorLock

Your vehicle doors are locked

Door Unlock

Your vehicle doors are unlocked and

the system is Disarmed

ArmedMode

Your vehicle is in armed mode

ValetMode

All the function shall be temporarily on

hold.

Remote Transmission

You are transmitting the signal to

control unit

In –Range Indicator

You are within the remote control

range.

Trunk/HoodTrigger

Trunk or Hood is illegally opened

(Zone 2)

Door Open Warning

Doors are illegally opened (Zone 3)

Shock Sensor Trigger

Trigger on Shock Sensor (Zone 4)

IgnitionTrigger

Trigger on Ignition Switch(Zone 5)

Warn Away trigger

Trigger on Shock Sensor (Zone 1)

Low Battery

You have to replace the battery of

remote control.

VibrationMode

Remote Control vibrates when the

system is triggered

Driver paging

/ Lose and Found

Someone is paging you in front of your

vehicle

Power Save M

ode

Save the battery power

AAA

PROGRAM MODE FORLCD REMOTE CONTROL TRANSCEIVER:

Trans

ceiv

er Button

System Function

Remark

ProgramMode -

Switching code

for

2nd /

1st Car Operation

Press within

seconds

ProgramMode -

Melody / Vibratio

n Mode

Press within

seconds

ProgramMode -

Power Save Mode

Press within

seconds

LCD screen lamp turns on for

5 seconds.

System’s Status Check

Press within 3 seconds

Clear the Flash Icon and Melody Sound

Press within 3 s

econds

1. Second Vehicle Security Operation: Your remote transmitter can be utilized to control a

second vehicle Autopage security system.To program the remote control transmitter to a

second vehicle, follow the instructions for Transmitter programming. All programming

parameters are the same except for the following:

For Regular Remote ControlTransmitter:

1. Prior to pushing any button on the transmitter. Press the Select II button first on the standard

transmitter.

2. Once IIbutton is pressed the LED on the transmitter will illuminate for 3.5 seconds.While the

LED is illuminated, press the button for the function you want to operate on the standard

remote transmitter to control a second vehicle security system.

For 2-way LCD RemoteControlTransceiver:

2ndCar Operation: While the “II” icon display on the LCD screen, you can remote control and

communicate with a second Autopage AM frequency security system. It has two short “bi”

soundswhile pressing the button of the LCD screen transceiver

1. Press and ho

ld all four remote control buttons simultaneously unit one long

beep is heard. LCD Programming has now been entered.

2. Within 5 seconds press and hold button until two beeping sounds is

heard and the “II”icon will display on the LCD screen to indicate thesecond

transceiver pin code has built-in.

3. To exit programming mode, take no action for five seconds. The remote

control will generate two long beeps to indicate programming mode has

been exited.

Back to 1st Car Operation:

You can remote control and communicate with a first vehicle security system. It has one short

“bi” sound while pressing the button of the LCD screen transceiver.

1. Press and hold all four remote control buttons simultaneously unit one long

beep is heard. Programming has now been entered.

2. Within 5 seconds press and hold button until one beepingsound is heard.

3. To exit programming mode, take no action for five seconds. The remote

control will generate two long beeps to indicate programming mode has been

exited.

Vibration / Melody Mode:

It is useful when you are in a noisy place and difficult to hear beep sound from the remote

control as the remote control in this mode, vibrates it if your security system is triggered.

1. Press and hold all four remote control buttons

simultaneously unit one long

beep is heard. Programming has now been entered.

2. Within 5 seconds, press the

button to select the mode of vibration or melody,

the icon will displayed

on the LCD screen to show the LCD remote

transceiver is on vibration mode.

3. To exit programming mode, take no action for five seconds. The remote control

will generate two long beeps to indicate programming mode has been exited.

Power Save Mode:

While the power save mode, the LCD remote transceiver “sleep”until a button is pushed,

extends the life of battery. When power save mode is “Off”, the remote control will wake up

periodically to check for messages from the security module.

1. Press and hold all four remote control buttons simultaneously unit one long

beep is heard. Programming has now been entered.

2. Within 5 seconds, press the button to toggle “On”or “Off”. The remote will

beep once for “On”, twice for “Off”. When power save mode is“On”, the

icon on the LCD screens to indicate entry the “power save mode”

3. To exit programming mode, take no action for five seconds. The remote control

will generate two long beeps to indicate programming mode has been exited.

Screen Lamp ON:

Press the button once; the LCD screen lamp will turns on for 5 seconds

ystem

’

Status

heck

When you want to check the system’s present status

through the LCD screen, Press the transceiver button first, within 3 seconds

press and buttons at the same time. It responds with one melody sound, the

LCD screen should be illuminated.

Note:If it has no responds then you are out of range.

Clear the Flash Icon and Melody Sound:

Cycle ignition then press the button first,within 3 seconds press and buttons at the

same time.It will clear theflash icon and melody sound on the LCD screen transceiver

Stop The Trigger Melody Sound:

While triggering the alarm the LCD screen will alert user through melody sound and flashing

trigger icon, press any button on the LCD remote transmitter to stop melody sound only, the

remote control buttons will not send acommand to the system.

ALARM OPERATING CONDITION:

Function

Siren

Parking

Lights

LED

Doors

Starter

Disable

Dome

Light

1. Arm

1 Chirp

1 Flash

Slow flash

Locking

2. Disarm

2or4

Chirps

2 o

r 3

Flashes

Off or Fast

flash

Unlocking

Off

On for

30 sec

3. Trigger

Alarming

Flashing

Slow flash

flashes

4. Panic

Alarming

Flashing

Slow flash

Locking

flashes

5.Car Locator

6 Chirps

12 Flashes

ALARM INDICATORS

CHIRP INDICATORS: PARKING LIGHTS:

Chirp

Function

Parking Light

Function

1 chirp Arm 1 flash Arm

2 chirps Disarm 2 flashes Disarm

3 chirps Defective

reminder

3 flashes Disarm/

Intrusion

4 chirps Disarm/

Intrusion 12 flashes Car

Locator

6 chirps Car Locator

LED INDICATORS:

LED

Function

LED

Function

Off Disarmed 2 flashes...

pause Trigger on trunk/hood

Slow

flash Armed 3 flashes...

pause Trigger on door

switch

Fast

flash Passive

arming 4 flashes...

pause Trigger on Dual Zone

Shock Sensor

(solid) Valet mode 5 flashes...

pause Trigger on Ignition

switch

Inhaltsverzeichnis

Andere Auto Page Autoalarmanlage Handbücher

Auto Page

Auto Page RF-303 Bedienungsanleitung

Auto Page

Auto Page RS-900LCD Bedienungsanleitung

Auto Page

Auto Page RF-505 Bedienungsanleitung

Auto Page

Auto Page RF-420LCD Bedienungsanleitung

Auto Page

Auto Page MA-200 Bedienungsanleitung

Auto Page

Auto Page Car-Pro CPX-2200 Bedienungsanleitung

Auto Page

Auto Page AP4000EX Technisches Datenblatt

Auto Page

Auto Page RF-350 rs Bedienungsanleitung

Auto Page

Auto Page Car-Pro CPX-3600 Bedienungsanleitung

Auto Page

Auto Page RF-305 Bedienungsanleitung

Auto Page

Auto Page RF-502 Bedienungsanleitung

Auto Page

Auto Page RF-320 Bedienungsanleitung

Auto Page

Auto Page RF-410 Bedienungsanleitung

Auto Page

Auto Page C3-RS-730 LCD Bedienungsanleitung

Auto Page

Auto Page A.P.I. EXP-52 Bedienungsanleitung

Auto Page

Auto Page RF-520LCD Bedienungsanleitung

Auto Page

Auto Page RF-425LCD Bedienungsanleitung

Auto Page

Auto Page RS-727LCD Bedienungsanleitung

Auto Page

Auto Page RF-503 Bedienungsanleitung

Auto Page

Auto Page RF-700 Bedienungsanleitung

Auto Page

Auto Page Telematics and Tracking Module Bedienungsanleitung

Auto Page

Auto Page C3-RS-915 LCD Bedienungsanleitung

Auto Page

Auto Page RS-720LCD Bedienungsanleitung

Auto Page

Auto Page RS-655 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung