Auto Page RSTKE-900 Bedienungsanleitung

RSTKE-900

PROFESSIONAL 915 MHz REMOTE CAR

STARTER & 6 CHANNEL KEYLESS ENTRY

SYSTEM

With

TwoWaySerialPortDataLink

Optional two Way Up grade Available

Compatible

OPERATION MANUAL

THISPRODUCTISDESIGNEDFORPROFESSIONALINSTALLATIONONLY

SVMASTER -       - http://www.msvmaster.lv

Auto Page, Inc. has over 25 years of experience in the vehicle security industry

intheUnitedStatesandisawhollyownedsubsidiaryofIwataElectricCo.,of

Tokyo, Japan. Iwata has been an industry leaderforover50years,

establishingareputationforingenuityinitsengineeringcapabilityand

innovative communication products. Auto Page and Iwata maintain a long

tradition of providing the best value to their customers.

C H ANG IN G T H E B A TT ERY I N Y O U R T R A N S M I T T E R S

XT- 9 0 S : This transmitter uses one (1) 3-voltlithiumionbattery(#CR2032)

that is placed with the (+) side facing upward. To replace the battery, you will

need to use a small flat blade screwdriver and a small Philips screwdriver.

Remove the small Philips head screw. Then locate the small notch on the

lowerrightsideofthetransmittercasenexttothekeyring. Usingtheflatblade

screwdriver, carefully pry the top case from the bottom case. It should snap

apart afterbreaking the seal. Before removing the battery note the direction of

the positive (+) terminal. Place the new battery in exactly the same manner,

being careful not to bend or damage the contact terminal. Snap the cases

back together andthentest thetransmitter to insure it arms and disarms the

alarm.ReinstallthePhilipsscrewtofinalizethebatteryreplacement.

XT-90S Extended Range Sliding Cover remote

CR20323 - Vo lt Ba tt er y

SVMASTER -       - http://www.msvmaster.lv

WARNINGS:

As with any product that performs automatic functions, there are certain safety

precautionsthatyoumustpracticeandbeawareof.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehi cle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is

corrected.

8. The use and operations of this system is the sole responsibility of the

operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle

runningonpublicstreets.

10.Itisnotsafetoremotestartthevehicleifthevehicleisparkedonasteep

incline.

OPERATION:

A. REMOTE TRANSMITTER OPERATION:

Transmitter

Button System Function Remark

L o c k D o o r s

Panic function P r e s s a n d H o l d f o r 3 s e c o n d s .

P r e s s t h e

button to stop.

C ar L o ca to r U n d e r a r m e d m o d e

U n l o c k D o o r s

-T w o S t e p s D o o r U n l o c k &

D i s a r m S y s t e m P r e s s t w i c e w i t h i n 3 s e c o n d s .

Trunk Release (Channel 3) Press and Hold for 2 seconds

Activate or Turn Off The

Remote Start Press twice within 3 seconds if programmed

f o r s a f e t y s t a r t

+ Channel # 4 TimerOutput(4)

+ Channel # 5 TimerOutput(5)

+ Channel # 6 TimerOutput(6)

ACTIVE LOCK:

SVMASTER -       - http://www.msvmaster.lv

1 . P r e s s button on the transmitter.

2 . T h e h o r n , i f i n s t a l l e d w i l l c h i r p o n c e a n d p a r k i n g l i g h t s w i l l f l a s h o n c e

indicating that the system is now active. The vehicle doors will lock upon

activating when interfaced with the keyless entry system.

ACTIVE UNLOCK:

1 . P r e s s button on the transmitter.

2 . T h e h o r n w i l l c h i r p t w i c e a n d p a r k i n g l i g h t w i l l f l a s h t w i c e t o i n d i c a t i n g

that the keyless system is now unlocked. The vehicle doors will unlock

and d ome l igh ts wi l l tur n on fo r 3 0 sec ond s .

PATHWAY ILLUMINATION:

This feature turns the parking light “ON” for 30 seconds upon an unlock

signal and for 10 seconds upon the lock signal. (Programmable)

TWO STEPS DOOR UNLOCK: (programmable) (optional)

T h i s f e a t u r e w i l l i n d e p e n d e n t l y u n l o c k t h e d r i v e r ’ s d o o r o n l y w h e n

disarming the security system. Pushing the button a second time

within 3 seconds will unlock the other doors.

DEACTIVATING WITHOUT A TRANSMITTER:

The Override function may be used if the remote transmitter is lost or

inoperative.

1 . E n t e r t h e v e h i c l e a n d t u r n t h e i g n i t i o n s w i t c h t o ‘ O N ’ p o s i t i o n .

2 . W i t h i n 1 0 s e c o n d s p u s h a n d r e l e a s e t h e v a l e t s w i t c h

VALET MODE:

The valet switch allows you to temporarily bypass all system function,

eliminatingtheneedtohandyourtransmittertoparkingattendantsor

garage mechanics. When the system is in valet mode, and remote

start functions are bypassed,EnterValetMode:

1 . F r o m t h e U n l o c k c o n d i t i o n , t u r n t h e i g n i t i o n t o “ O N ” p o s i t i o n .

2 . P u s h a n d h o l d v a l e t s w i t c h f o r 2 s e c o n d s u n t i l t h e L E D t u r n s o n . T h e

LED will remain on as long as the system is in ‘valet mode’.

Exit Valet Mode:

1 . R e t u r n t o n o r m a l o p e r a t i o n , t u r n i g n i t i o n ‘ o n ’ .

2. Push and hold valet switch for 2 seconds, The LED will turn off

indicating the system has exited the valet mode.

SVMASTER -       - http://www.msvmaster.lv

CAR LOCATOR

Under armed mode, press the

button to activate the car locator

function. The horn, if installed

will chirp 6 times. The parking light will

flash12times,foryoutoeasilylocateyourcar.

PANIC FUNCTION:

Thetransmittercanbeusedasaremotepanicswitchtomanuallytriggerthe

alarmincaseofanemergency.

1.Pressandholdthe buttonfor3 second.Thehornifinstalledwill

immediately sound.

2.Duringpanicmode,thenormalfunctionofthistransmitterbuttonwill

be disabled. The transmitter and buttonscanbeusedtolock

andunlockthedoor(iftheoptionisinstalled),howeveroncethe

b ut t o n i s pr es se d, t h e v e hi cl e’ s st a r t e r d is ab le d e v i c e , (w he re

installed)willbedisengagedallowingthevehicletostart.

3 . Tostopthealarm,pressandholdthetransmitter or buttonon the

transmitteragainfor3seconds or press or to stop immediately.

If the button is not pressed, the alarm will automatically stop after 30

seconds.

TRUNK RELEASE (CHANNEL 3) OUTPUT.

Pressandhold buttononthetransmitterfor threesecondstoremotely

releasethetrunkorotherelectricdevices.

IGNITION CONTROL DOOR LOCK/UNLOCK.

If the vehicles power door locks have been interfaced to the unit, the

system will automatically lock the vehicle's doors in 3 seconds when the

ignition is turned “ON” and /or unlock the vehicle’s doors when the

ignition is turned “OFF”. (Programmable)

CHANNEL 4 TIMER CONTROL OUTPUT

SVMASTER -       - http://www.msvmaster.lv

Pressingthetransmitter and button at the same time will activate

theChannel4function.Channel4isuser-programmabletimeroutput.You

mayprogramthebuilt-intimertosendagroundsignalforanytimeduration

from1secondto120seconds.Forinstance,thistimeroutputmaybeused

to turn on the headlight, power window or sunroof. (Factory defaults setting

at momentary output.)

CHANNEL 5 TIMER CONTROL OUTPUT

Pressingthetransmitter and

buttons at the same time will activate

the Channel 5 function. Channel 5 is user-

programmable timer output. You

may program thebuilt-intimertosendagroundsig

nal for any time duration

from1secondto120seconds.Forinstance,thistimeroutputmaybeusedto

turn on the headlight, power window or sunroof. (Factory defaul

ts setting at

momentaryoutput.

CHANNEL 6 TIMER CONTROL OUTPUT

Pressingthetransmitter and

buttons at the same time will activate

the Channel 6 function. Channel 6 is user-

programmable timer output. You

may program thebuilt-

in timer to send a ground signal for any time duration

from1secondto120seconds.Forinstance,thistimeroutput

maybeusedto

turnontheheadlight,powerwindoworsunroof.

(Factorydefaultssettingatmomentaryoutput.)

SECOND VEHICLE SECURITY OPERATION:

Your 5-button remote transmitter can be utilized to control a second vehicle

security system, To program the remote control transmitter to a second

vehicle,followtheinstructionsforTransmitterprogramming.

II Switching code For 2nd Car

Operation

For regular remote transmitter

Only

OPTIONAL TWO WAY UPGRADE:

This system can be easily upgraded by purchasing a compatible two

way remote control for this system. Two way communication will allow

you to have access to vehicle information and condition as well as

confirmation of all sent commands.

T h e X T - 9 0 L C D a n d X T - 1 0 0 O L E D a r e b o t h c o m p a t i b l e w i t h t h e

RSTKE-900 and can be purchased from an authorized Autopage dealer.

To view these transmitters go to www.autopageusa.com .

.REMOTE START OPERATION:

SVMASTER -       - http://www.msvmaster.lv

TO R E M OTE START THE VEHICL E:

When you want to start your vehicle,

1. Press button once on the transmitter.

2. The parking lights will activate to indicate the remote start received

the signal.

3. The engine will start in approximately 5 seconds.

4. Once the engine is running and after couple seconds the parking

lights will turn on again and climate controls will activate and adjust the

vehicles interior temperature to your preset setting. (While the vehicle is

running, the “minutes” digit on the LCD screen will flash and will indicate

a count down timer based on the 5, 10, 20 or 30 minute run time set up

by yourinstallationcenter.)

5. The vehicle will run for 5 to 30 minute cycle and automatically shut

down. (When the unit shuts off the count down timer will turn off and the

transmitter will play a melody sound.)

NOT E: The Remote Start Unit will not start the vehicle if any one of the

following conditions exists:

1 . T h e h o o d i s o p e n e d .

2. The brake pedal is pressed.

3. The remote start enable toggle switch is in the OFF position. (If

installed)

4. The gear selector is in any gear other then “PARK” or “NEUTRAL”

SAFE START (Child safety mode)(programmable)

The factory default setting to start the vehicle is to press the button

ONCE on the transmitter. Programming this feature to eliminate an

accidental remote start operation,

1. The user must press the transmitter button twice within 3

seconds to start the vehicle. or

2. The user must press the transmitter and buttons at the same

time to start the vehicle.

TO O P ERATE THE VEHICLE WHILE RU N NING ON THE REMOTE

START:

To operate the vehicle while the engine is running on the remote start:

1 . I n s e r t t h e i g n i t i o n k e y a n d t u r n i t t o “ O N ” ( n o t t h e s t a r t ) p o s i t i o n .

2 . P r e s s t h e b r a k e p e d a l .

Note: If the brake pedal is pressed before the key is in the ON position,

the engine will shut down.

TEMPOR A RY STOP F E ATURE:

SVMASTER -       - http://www.msvmaster.lv

This feature allows the vehicle to remain running after the key has been

removed from the ignition. This feature is useful for occasions when you

wish to exit and lock the vehicle for short periods of time, but would like

to leave the motor running and the climate control on.

1 . B e f o r e t u r n i n g o f f t h e e n g i n e , p r e s s t h e button on the transmitter

and the LED indicator will flash 3 times to confirm entry.

2 . T u r n t h e i g n i t i o n k e y t o O F F p o s i t i o n . ( T h e e n g i n e w i l l s t a y r u n n i n g . )

3 . T h e e n g i n e w i l l r u n u n t i l t h e p r e - p r o g r a m m e d t i m e h a s e l a p s e d o r

shutdown input is received. If the brake pedal is depressed the engine

willstop.

T U R B O C H A R G E M O D E : (programmable)

Turbo charge mode keeps the engine running after arriving at your

destination for a programmable period of 1, 3 or 5 minutes. This allows

the vehicle’s engine time to conveniently cool down the turbo after you

have left the vehicle. To activate:

1. While the engine is running, pull up the hand brake and place the

transmission gear in the park position.

2. Before turn ing off the engine, pres s and release and buttons at

thesame time.

-- The LED will flash indicating the remote start has entered the turbo

charge mode.

3. Take the “Ignition Key” from the key cylinder.

-- Engine keeps running. --

4. Exit and secure the vehicle.

-- Engine continues running until the pre-programmed time has

elapsed. --

NOTE: This feature only applies to vehicles with Turbo Engines.

TO TURN OFF THE REMOTE START:

When the engine is running (by remote start), if you want to stop it,

1.Press

button once on the remote transmitter while in the remote

start mode.

2.Press the brake pedal.

The vehicle will shut down and turn off the

parking lights will indicate engine has stopped

3.Movetheoptionalremotestartena

ble toggle switch to OFF position. (If

installed)

SHUT-DOWN INPUT FOR REMOTE STARTER:

SVMASTER -       - http://www.msvmaster.lv

If any of the following conditions exist while the system is operating, the

engine will not start or will shut down immediately:

1.Thehoodisopened.

2.Thebrakepedalispressed.

3.Engineisover-revved.{“Tachometercheckingtype”only}

4.Thepre-programmedruntime(5/10/20/30minutes)haselapsed.

5.Press buttononceontheremotetransmitterunderremotestart

mode.

6.TheoptionalremotestartenabletoggleswitchisintheOFFposition.(If

installed)

7.Thevehiclerefusedtostartrunningafter{3}unsuccessfulattempts.

DISABLING THE REMOTE START SYSTEM:

(Toggle switch If installed)

This feature allows your system’s remote start unit to be temporarily

disabled to prevent the vehicle from being remote started accidentally.

This feature is useful if the vehicle is being serviced or stored in an

enclosed area. To disable the remote start, move the optional remote

start enable toggle switch to the OFF position.

SVMASTER -       - http://www.msvmaster.lv

Andere Handbücher für RSTKE-900

Inhaltsverzeichnis

Andere Auto Page Fernstartsystem Handbücher

Auto Page

Auto Page C3-RS-601 Bedienungsanleitung

Auto Page

Auto Page C3-RS-603 Bedienungsanleitung

Auto Page

Auto Page RS-777 Bedienungsanleitung

Auto Page

Auto Page C3-RS1100 OLED Bedienungsanleitung

Auto Page

Auto Page Car-Pro CPX-RS2 Bedienungsanleitung

Auto Page

Auto Page Car-Pro CPX-RS1 Bedienungsanleitung

Auto Page

Auto Page RS-730 Bedienungsanleitung

Auto Page

Auto Page RS-601 Bedienungsanleitung

Auto Page

Auto Page C3-RS-1000 OLED Bedienungsanleitung

Auto Page

Auto Page C3-RS-665 Bedienungsanleitung

Auto Page

Auto Page RS-727LCD Bedienungsanleitung

Auto Page

Auto Page XT-12 Bedienungsanleitung

Auto Page

Auto Page TRX950 Bedienungsanleitung

Auto Page

Auto Page RS-615 Bedienungsanleitung

Auto Page

Auto Page KE-120 Bedienungsanleitung

Auto Page

Auto Page RS-622 Bedienungsanleitung

Auto Page

Auto Page C3-RS-601 Bedienungsanleitung

Auto Page

Auto Page C3-RS-625 Bedienungsanleitung

Auto Page

Auto Page RS-602 Bedienungsanleitung

Auto Page

Auto Page C3-RS-625 Bedienungsanleitung

Auto Page

Auto Page RS-660 Bedienungsanleitung

Auto Page

Auto Page C3-RS-665 Bedienungsanleitung

Auto Page

Auto Page RS-610 Bedienungsanleitung

Auto Page

Auto Page C3-RS-603 Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch