Automatic Technology GDO-6 EasyRoller Bedienungsanleitung

Home Owner’s Manual

Doc #: 160005_01

Part #: 13368

Released: 05/0314

GDO-6 EasyRoller®

Roll Up Garage Door Opener

GDO-6 EasyRoller®

GDO-6 EasyRoller®Home Owner’s Manual

Table of Contents

1. Safety Rules 3

2. Features 4

3. Specifications 5

4. Operating your door 6

5. User Operating Controls 7

6. Manual Release

Security 8

6.1 Manual Door Operation 8

6.2 Emergency Evacuations 8

6.3 Power Failure 8

6.4 Re-Engaging the Opener 8

6.5 Security - Inbuilt Locking Facility 8

7. Safety Testing 9

7.1 Test the Close Cycle 9

7.2 Testing the Open Cycle 9

7.3 Test the Manual Door Operation 9

7.4 Setting the PET Mode position 9

8. Coding Transmitters 10

8.1 Setting the Transmitter to Operate the Door 10

8.2 Setting the Transmitter to Operate Vacation Mode 10

8.3 Setting the Transmitter to Operate PET (Pedestrian) Mode 10

8.4 Setting the Transmitter to Operate the Courtesy Light 11

8.5 To Erase Programmed Codes 11

8.6 Remotely Coding Transmitters 11

9. Troubleshooting Guide 12

10. Maintenance 14

10.1 Door Maintenance 14

10.2 Lubrication (every 3 - 6 months) 14

10.3 Door Service and Repair 14

10.4 Opener Maintenance 15

10.5 Service Indicator 15

10.6 Removing the Battery From the Transmitter 15

11. Warranty 16

12. Optional Accessories 18

13. Service Schedule 19

GDO-6 EasyRoller®Home Owner’s Manual

Table of Contents

1. Safety Rules

Please read these important safety rules

This automatic garage door opener is designed and tested to offer safe service provided it is

installed and operated in strict accordance with the following safety rules. Failure to comply with

the following instructions may result in death, serious personal injury or property damage.

WARNING! • When operating the manual release while the door is open, the

door may fall rapidly due to weak or broken springs, or due to being

improperly balanced.

• Do not disengage the opener to manual operation with children/

persons or any objects including motor vehicles within the doorway.

• If the door is closing and does not re-open when obstructed,

discontinue use. Do not use a door with faulty obstruction sensing.

ELECTROCUTION! • Place opener in protected area so that it does not get wet.

• Do not spray with water .

• Do not open the protective covers.

• Do not operate opener if cable is damaged.

CAUTION:

Emergency access • If your garage has no pedestrian entrance door, an emergency

access device should be installed. This accessory allows manual

operation of the garage door from outside in case of power failure.

Entrapment under

operating door

• Watch the moving door and keep people away until the door is

completely opened or closed. Do not operate door when persons

are near the door.

• Do not allow children to play with door controls or transmitters.

• Regularly conduct Open and Close cycle testing.

• Ensure the garage door is in good working order by undertaking

regular servicing.

• Wall transmitters should be installed in a location where the garage

door is visible, but out of the reach of children at a height of at

least 1.5m.

• Install Safety Beams (recommended).

Fall from Ladder • Ensure ladder is the correct type for the job.

• Ensure ladder is on flat ground.

• Ensure user has 3 points of contact while on ladder.

Entanglement in or

laceration from

moving door

• Keep hands and loose clothing clear of door and guides at all times.

• Keep hands clear of moving door as sharp edges can cause cuts or

lacerations.

DO NOT DO IT

YOURSELF

• Keep the garage door balanced. Sticking or binding doors must be

repaired. Garage doors, door springs, brackets and their hardware

are under extreme tension and can cause serious personal injury.

Do not attempt any garage door adjustment. Do not use if repair or

adjustment is needed. Call for a professional garage door service.

DIY

Automatic Technology (Australia) Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, statutory or otherwise which may be

implied by laws as conditions or warranties of purchase of a Automatic Technology (Australia) Pty Ltd Garage Door Opener. Automatic Technolofy (Australia) Pty Ltd hereby further

expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person as a result whether directly or indirectly from failure to install the

Automatic Technology ( Australia) Pty Ltd Garage Door Opener in accordance with the installation instructions.

GDO-6 EasyRoller®Home Owner’s Manual

Warranty

Two (2) year/5,000 cycles full parts and labour

warranty on motor, electronics and mechanical

components of the opener when installed by an

Automatic Technology Dealer.

TrioCodeTM128 Technology

Only transmitters with the TrioCodeTM128

Technology can operate with the latest Openers,

reducing the chance of interference from other radio

frequency sources. TrioCodeTM128 transmitters

have the ability to code into earlier model openers.

Code Hopping Technology

Every time a transmitter is used a new security code

is generated from over 100 billion possible code

combinations. This greatly enhances the security of

the system and makes “code grabbing” a thing of

the past!

Multi-Channel Transmitter

Multi-channel transmitters allow you to operate

other devices such as an adjoining garage door or

automated gate from the same handy unit.

Safety Reversing System

The automatic safety reverse system significantly

reduces the risk of death or serious injury if

trapped by a closing door. The safety reverse force

can be adjusted for environmental conditions such

as windy areas.

Memory Retention

In case of a power failure the opener does not lose

the transmitter codes or limit settings.

Manual Release

The manual release handle allows the door to be

operated by hand in the event of a power failure.

Easy Access Transmitter

Inside the manual release handle is a transmitter

designed to be in easy reach so that the garage

door can be operated without having to stretch to

reach the operate button on the control panel.

Self Locking

There is no need to manually lock your garage

door, as the opener ‘positively’ locks the door when

closed.

Service Indicator

The opener has a built in service counter. From

factory this is loaded with 3000 cycles. When this

counter expires, the service yellow LED will light

up and at the start of each door movement the

beeper will sound three times. After opening

or closing the door the courtesy light will flash

and beeper sound five times. Contact your

dealer/installer for service. (Refer to 10.5 for

information).

Service Fault Indicator

Flashing LEDs on the control panel easily identify

operational problems or service requirements.

Dynamic Door Profiling

Changing door characteristics are automatically

compensated for and “learnt” with each

operation of the door.

Vacation Mode

A transmitter can be programmed to disable

the garage door opener radio receiver. This is

ideal if the door is to be left idle for prolonged

periods. (Refer to 8.2 for information)

Pet (Pedestrian) Mode

A transmitter can be programmed to open

the door partially to allow pets access to the

garage. The default PET Mode height can be

adjusted to a desired position. (Refer to 7.4 for

information). To code a transmitter button to

operate PET mode refer to 8.3 for information.

LED Courtesy Light

Using the latest Light Emitting Diode (LED)

technology, the opener features two LEDS

These LEDS produce a brilliant white light that

illuminates the garage upon activation.

The LED courtesy light automatically switches

on for approximately four (4) minutes (time

programmable) when operating the door. This

can also be programmed to turn on and off

from a transmitter. (Refer to 8.4 for information)

2. Features

GDO-6 EasyRoller®Home Owner’s Manual

3. Specifications

Technical Specifications

Power supply 230V - 240Va.c. 50Hz

Maximum door opening:

Width:

Height:

Weight:

5500mm (16.5 m2)

3000mm

100kg

Minimum sideroom 40mm

Lift force 500N (50kg)

Nominal force 150N (15kg)

Receiver type UHF Multi-frequency FM Receiver

Receiver code storage capacity GDO-6v3: 14 X 4 button Transmitter Codes

GDO-6v4: 64 x 4 button Transmitter Codes

Transmitter frequency TrioCodeTM128 Technology

Coding type Mulit-frequency Code Hopping

Number of code combinations Over 100 billion random codes

Code generation Non-linear encryption algorithm

Transmitter battery CR2032 (3 Volts)

Courtesy light LED (Light Emitting Diodes)

Note: Intermittent operations may occur in areas which experience very strong winds. The strong wind

puts extra pressure on the door and tracks which may in turn intermittently trigger the safety obstruction

detection system.

GDO-6 EasyRoller®Home Owner’s Manual

Fig. 4.1

Transmitter

•To operate the opener, press the programmed

transmitter button until your door begins to move

(usually 2 seconds). Make sure you can see the

door when you use the transmitter.

•If you are in a vehicle you should aim the

transmitter through your windscreen (Fig. 4.1).

•Check that the door is fully closed before you

drive away.

•If you press the transmitter whilst the door is

moving the door will stop. The next press of the

transmitter will move the door in the opposite

direction.

The transmitter may also be programmed to operate

the following features (Refer to Section 8 for full

details):

•Turn the courtesy light on and off without

operating the door,

•Put the garage door opener into “Vacation Mode”

where it will not respond to any transmitters.

NOTE: Additional transmitters may be purchased at

any time.

CAUTION: Activate the opener only

when the door is in full view, free of

obstructions and with the opener

properly adjusted. No one should enter

or leave the garage while the door is in

motion. Do not allow children to play

with or near the door.

ELECTROCUTION! This opener is a

mains voltage plug-in domestic appliance

and there are no user serviceable parts

inside this opener.

For maximum efficiency of your opener, your garage

door must be in good operating condition.

An annual service of your garage door by a Dealer is

recommended.

4. Operating your door

GDO-6 EasyRoller®Home Owner’s Manual

Door Status Indicators OPEN LED (green) CLOSE LED (red) Beeper

Open On

Close On

Opening Flashing

Closing Flashing

Door travel stopped Flashing Flashing

Door obstructed when opening Flashing Beeps while door is

moving

Door obstructed when closing Flashing Beeps while door is

moving

Opener overloaded Alternating flashes Alternating flashes

Door in open position with

Auto-Close mode selected

One second flashes

Mains power interrupted Rapid flashes

5. User Operating Controls

Button (Fig 5.1) Function

1. OPERATE Opens/stops/closes the door

2. CODING LED (Red) Flashes when a code is being stored or when the transmitter button is

pressed

3. LIGHT CODE (White) Is used for storing or erasing the transmitter button (code) you wish to use

to switch the courtesy light on the opener on or off.

4. DOOR CODE (Blue) Is used for storing or erasing transmitter buttons for door operation

5. OPEN LED (Green) Illuminates and flashes as the door opens and remains on when the open

limit position has been reached.

6. DOOR STATUS LED (Yellow) Illuminates when Service is due.

7. CLOSE LED (Red) Illuminates and flashes as the door opens closes, and remains on when the

close limit position has been reached.

Fig. 5.1

GDO-6 EasyRoller®Home Owner’s Manual

6. Manual Release

Security

TO DISENGAGE:

PULL HANDLE DOWN

& RELEASE

TO RE-ENGAGE:

REPEAT ACTION

PULL

HANDLE

Fig. 6.1

WARNING! When operating the

manual release (while the door is

open) the door may fall rapidly due

to weak or broken springs, or due to

being improperly balanced.

Do not disengage the opener to

manual operation with children/

persons or any objects including

motor vehicles within the doorway. 6.2 Emergency Evacuations

In emergencies the garage door can be disengaged

from the opener, via the manual release cord and

the door opened manually. The manual release cord

should be a maximum of 1.8m from the ground. The

cord can be adjusted for special considerations.

6.3 Power Failure

When there is a power failure, the opener will be

unable to automatically open or close your garage

door. To use your door whilst there is no power you

will need to disengage the opener and use the door

manually – see 6.1 Manual Door Operation.

6.4 Re-Engaging the Opener

When the door has been disengaged from the

opener, before re-engaging, ensure that the door

has not been locked by a locking device (preferably

by lifting the door open to waist height). Re-engage

the opener (Fig 6.1) and then press the easy access

transmitter button at the end of the string handle.

Then the door will operate as normal.

CAUTION: When the opener is manually

disengaged, the door is no longer locked.

To lock the door manually, either use a

locking device or re-engage the opener

after the door is closed.

6.1 Manual Door Operation

To disengage the opener from the door (preferably

with the door in the closed position), pull down on

the string handle (Fig 6.1). This will allow you to

manually open or close the door.

To re-engage the opener refer to 6.4 Re-Engaging

the Opener.

6.5 Security - Inbuilt Locking Facility

DO NOT lock your door when your opener is

engaged as it has inbuilt locking facility. With the

opener engaged your door will be locked whether

the power is on or off.

WARNING! Please test the manual

release mechanism to ensure that the

manual release is easy to operate.

No more than 15 kg of force should

be required to disengage the door

using the manual release cord. If

excessive force is required contact

your door professional immediately

and ask them to reset the close limit

position.

GDO-6 EasyRoller®Home Owner’s Manual

6. Manual Release

Security

7. Safety Testing

7.1 Test the Close Cycle

a. Press the transmitter to open the door. (Fig 7.1)

b. Place a piece of timber approximately 40mm high

on the floor directly under the door (Fig 7.2)

c. Press the programmed transmitter to close door.

d. The door should strike the object and re-open.

7.2 Testing the Open Cycle

a. Press the transmitter to close the door (Fig. 7.1).

b. Press again to open the door.

c. When the door reaches approximately half way,

firmly grab the door’s bottom rail - the door

should stop.

If the door does not reverse readily when closing, or

stop when opening, put the door into manual and

contact your door professional immediately for a

door service.

7.3 Test the Manual Door Operation

Periodically disengage the opener (Section 6.1) and

manually operate the door. The door must be smooth

to operate by hand. The force required on the bottom

rail should not exceed 15 kg.

7.4 Setting the PET Mode position

When activated, PET mode drives the door to the

preset position from the close position.

a. Drive and stop the door at the deisred PET mode

open position by pressing the transmitter button

coded for Open/Stop/Close operation.

b. Press and hold the OPEN button on the opener for

six (6) seconds until the OPEN and CLOSE LED’s

are lit to record the new PET position.

To program a transmitter button to operate PET mode

refer to 8.3 Code Transmitter for PET Mode.

Periodically test if a PET mode button is pressed, while

the door is moving, the door will stop or when the

door is in the PET position, the door will close.

CAUTION: Take care when

completing a safety test. Failure

to follow this warning can result

in serious personal injury and/or

property damage.

40mm

WARNING! If the door is closing

and is unable to re-open when

obstructed, discontinue use.

Do not use a door with faulty

obstruction sensing. Contact your

door professional for support.

Fig. 7.2

Select the button on

the transmitter that has

been programmed to

operate the door.

If transmitter is not programmed,

Refer to Section 8 to program

transmitter.

Fig. 7.1

GDO-6 EasyRoller®Home Owner’s Manual

8. Coding Transmitters

Press and hold DOOR

CODE button once

Select one of the four buttons on

key transmitter you wish to use to

control the door. Or the button on

the end of the manual release cord.

Fig. 8.1

8.1 Setting the Transmitter to Operate the Door

The opener can only operate from transmitters that have

been programmed into its receiver. The receiver needs to

learn the codes of any transmitter that will be used with the

operator. Up to sixty four (64) codes can be stored in the

receiver’s memory.

a. Ensure the button cover has been removed (see

Electrocution caution) and the opener is turned on.

b. Press and hold the DOOR CODE button. The DOOR

CODE LED will illuminate and beep to indicate the

opener is in Code Learn mode (Fig. 8.1).

c. Press and hold the transmitter button that you want to

control the door for two (2) seconds, pause for two (2)

seconds, then press the same button again for two (2)

seconds and release.

d. Release the DOOR CODE button.

e. Press the transmitter button to test.

8.2 Setting the Transmitter to Operate

Vacation Mode

The opener can be programmed into a “Vacation Mode”

where the opener will not respond to any transmitter

except one preprogrammed unit.

f. Briefly press the DOOR CODE button once, then press

it again and hold (will beep two times on second press

(Fig. 8.2).

g. Press one of the four (4) buttons on the transmitter for

two (2) seconds, pause for two (2) seconds, then press

the same button again for two (2) seconds.

h. Release DOOR CODE button.

i. Press and hold the transmitter button for six (6)

seconds to set Vacation Mode. The door code LED

will stay lit while Vacation Mode is active.

To reset Vacation Mode, press the same transmitter

button for two seconds.

8.3 Setting the Transmitter to Operate

PET (Pedestrian) Mode

a. Briefly press the DOOR CODE button three (3) times,

then press it again and hold (the opener will beep four

times on the fourth press.

b. Choose a transmitter button not already coded into

the receiver. Press and hold this button for two (2)

seconds, pause for two (2) seconds, then press the

same button again for two (2) seconds and release.

c. Release the DOOR CODE button.

d. Press the transmitter button to test. Fig. 8.2

Press DOOR

CODE button

twice.

Select one of the

four buttons (not

programmed yet

) you wish to use

to control the

Vacation Mode

ELECTROCUTION! The button

cover is the only cover that should

be removed. All other covers must

remain in place.

CAUTION: Be careful not to press

the operate button while removing

the button cover as the door will

start to move.

Illuminated

LED

indicates

mode is active

IMPORTANT NOTE: Only TrioCodeTM 128

Technology Transmitters are compatible

with this GDO-6V4 product.

Andere Handbücher für GDO-6 EasyRoller

Inhaltsverzeichnis

Andere Automatic Technology Garagentoröffner Handbücher

Automatic Technology

Automatic Technology GDO-11V3 Ero Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-6 EasyRoller Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-6v3 EasyRoller Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-8 Shed Master Bedienungsanleitung

Automatic Technology

Automatic Technology ATS Series Bedienungsanleitung

Automatic Technology

Automatic Technology SecuraLift GDO-7V1 Kurzanleitung

Automatic Technology

Automatic Technology SecuraLift Trio Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9 Dynamo Gen 2 Bedienungsanleitung

Automatic Technology

Automatic Technology Ero GDO-11v2 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9v2 Enduro Gen 2 Bedienungsanleitung

Automatic Technology

Automatic Technology Toro GDO-10V2L2 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-10V3L2 Toro Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9 Dynamo Gen 2 Bedienungsanleitung

Automatic Technology

Automatic Technology NeoSlider TrioCode 128 NES-500 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-11 Ero Bedienungsanleitung

Automatic Technology

Automatic Technology Axess Pro Series 1101 Kurzanleitung

Automatic Technology

Automatic Technology GDO-2 SecuraLife Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-6 v2 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-8V2 EasyRoller II Bedienungsanleitung

Automatic Technology

Automatic Technology iOpener RD40 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-7v2 SecuraLift Bedienungsanleitung

Automatic Technology

Automatic Technology SecuraLift GDO-9v3 Bedienungsanleitung

Automatic Technology

Automatic Technology Dominator AM800 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-8v1 EasyRoller II Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Chamberlain

Chamberlain 8355 - 1/2 hp Bedienungsanleitung