Automationdirect.com Productivity 2000 P2-8AD4DA-1 Bedienungsanleitung

Sales 800-633-0405 www.productivity2000.com

2000

1I00.00

2I04.00

3I00.00

4I04.00

5I00.00

6I04.00

7I00.00

8ISPARE

Terminal Block sold separately, (see wiring options on page 3).

Warranty: Thirty-day money-back guarantee. Two-year limited replacement.

(See www.productivity2000.com for details).

P2-8AD4DA-1

Analog Input/Output

The P2-8AD4DA-1 Current Analog Input/Output

Module provides eight channels of 0-20 mA

inputs and four channels of 4-20 mA outputs

for use with the Productivity2000 System.

General Specifications ...................... 1

Input Specifications ......................... 2

Output Specifications ....................... 2

Wiring Options............................. 3

Module Configuration ....................... 3

Linear Scaling ............................. 4

Non-Linear Scaling ......................... 4

OLED Panel Display Menus .................. 5

Module Installation Procedure................. 6

QR Code ................................. 6

Hot Swap Information ....................... 6

Wiring Diagram and Schematic................ 7

Warning .................................. 8

Removable Terminal Block Specifications. . . . . . . . 8

General Specifications

Operating Temperature 0º to 60ºC (32º to 140ºF)

Storage Temperature -20º to 70ºC (-4º to 158ºF)

Humidity 5 to 95% (non-condensing)

Environmental Air No corrosive gases permitted

Vibration IEC60068-2-6 (Test Fc)

Shock IEC60068-2-27 (Test Ea)

Field to Logic Side Isolation 1800VAC applied for 1 second

Insulation Resistance > 10MΩ @ 500VDC

Heat Dissipation 2.47W

Enclosure Type Open Equipment

Agency Approvals UL508 File E139594, Canada & USA

CE (EN61131-2*)

Module Keying to Backplane Electronic

Module Location Any I/O slot in a Productivity2000 System

Field Wiring Use ZIPLink Wiring System or removable terminal block

(not included). See “Wiring Options” on page 5.

EU Directive

See the “EU Directive” topic in the Productivity2000

Help File. Information can also be obtained at:

www.productivity2000.com

Connector Type (not included) 18-Position Removable Terminal Block

Weight 90g (3.2 oz)

*Meets EMC and Safety requirements. See the D.O.C. for details.

2Tech Support 770-844-4200www.productivity2000.com

Input Specifications

Input Channels 8 (1 common)

Module Signal Input Range 0-20 mA (sourcing)

Signal Resolution 12-16 bit, depending on input resolution

Input Resolution & Update Rate

(See Note 1)

Fine: 8ms, 0.305 μA, 16 bit

Medium: 2ms, 1.22 μA, 14 bit

Coarse: 700μs, 4.88 μA, 12 bit

Data Range 0-65535 counts

Input Type Single Ended (1 common)

Maximum Continuous Overload ±31mA

Input Impedance 250Ω ±0.1%, 1/4W

Hardware Filter Characteristics Low pass 1st order, -3dB @ 48Hz

All Channel Update Rate

(See Note 2)

Fine 57ms

Medium: 17ms

Coarse: 7ms

Open Circuit Detection Time Zero reading within 1s

Conversion Method Successive approximation

Accuracy vs. Temperature ±15ppm/°C maximum

Maximum Inaccuracy 0.1% of range

Linearity Error (end to end) 0.015% of range maximum

Monotonic with no missing codes

Input Stability and Repeatability ±0.015% of range (after 10 minute warm-up)

Full Scale Calibration Error

(not including offset) ±0.05% of range maximum

Offset Calibration Error ±0.05% of range maximum

Maximum Crosstalk -96dB ±1 -0.015% of full scale maximum

Recommended Fuse (external) Edison S500-32-R, 0.032 A fuse

External DC Power Required 24VDC (-20% / +25%), 145mA

Output Specifications

Output Channels 4 (1 common)

Module Signal Output Range 4-20 mA

Output Signal Resolution 16-bit

Resolution Value of LSB

(least significant bit)

0.244 μA / count

1 LSB = 1 count

Data Range 0 - 65535 counts

Output Type Current sourcing: 20mA max

Output Value in Fault Mode ≤ 4mA

Load Impedance

(Minimum External Power Supply)

0 - 480Ω (19.2 VDC)

0 - 600Ω (21.6 VDC)

0 - 715Ω (24VDC)

0 - 840Ω (26.4 VDC)

0 - 1010Ω (30VDC)

Maximum Inductive Load 1mH

Allowed Load Type Grounded

Maximum Inaccuracy 0.1% of range

Maximum Full Scale Calibration

Error (not including offset error) ±0.065% of full scale

Maximum Offset Calibration Error ±0.065% of full scale

Accuracy vs. Temperature ±15ppm/°C max full scale calibration change

(±0.0025% of range/°C)

Max Crosstalk -96dB, 1 LSB

Linearity Error (End to End) ±0.015% of range maximum

Monotonic with no missing codes

Output Stability and Repeatability ±0.015% after 10 minute warm-up typical

Output Ripple 0.01% of full scale at 50/60 Hz

Output Setting Time

Rising Time 200μs

Falling Time 135μs

(full scale change)

All Channel Update Rate 3.55 ms

Maximum Continuous Overload Outputs open circuit protected

Type of Output Protection Electronically current limited to 20mA or less

Output Signal (power-up, -down) ≤ 4mA

Note 1: The Input Resolution of Fine returns 16 bit resolution. Medium and Coarse are 14

and 12 bit respectively. The 12 and 14 bit input values are scaled to 0-65535.

Note 2: Valid when all channels are set for the same Input Resolution.

Sales 800-633-0405 www.productivity2000.com

Current Input Circuits

Current Output Circuits

COM

3-Wire Current

Transmitter

.032A

2-Wire 4-20 mA

Transmitter

fuse

2-Wire Transmitter

3-Wire Transmitter

+24VDC User

Supplied Power

–

.032A

fuse

Note: Do not connect both ends of shield.

4-Wire 4-20 mA

Transmitter

4-Wire Transmitter

–

User Supplied

Transmitter Power

AC or DC

4 - 20mA

Load

Note: Shield is connected to common at the source device.

+24VDC User

Supplied Power

An Edison S500-32-R

0.032A fast-acting fuse

is recommended for all

4-20 mA current loops.

.032A

fuse

+–

I1+

I2+

I3+

I4+

I5+

I6+

I8+

I7+

COM

24V+

- +

24 VDC User

Supplied Power

CH1 ADC

CH2 ADC

CH3 ADC

CH4 ADC

CH5 ADC

CH6 ADC

CH7 ADC

CH8 ADC

ISOLATED ANALOG

CIRCUIT POWER

ISOLATED ANALOG

CIRCUIT COMMON

INTERNAL

MODULE CIRCUITRY

COM

I2+

I1+

I3+

I4+

CH1 DAC

CH2 DAC

CH3 DAC

CH4 DAC

Note: This module includes input and output channels. Before connecting

eld wiring, verify that you are connecting to the appropriate terminals

COM

Output Channels Input Channels

12345678910 11 12 1813 14 15 16 17

Wiring Diagram Schematic

6Tech Support 770-844-4200www.productivity2000.com

QR Code

Use any QR Code reader application to

display the module’s product insert.

Important Hot-Swap Information

The Productivity2000 System supports hot-swap!

Individual modules can be taken offline, removed, and

replaced while the rest of the system continues con-

trolling your process. Before attempting to use the hot-

swap feature, be sure to read the hot-swap topic in the

programming software’s help file or our online documen-

tation at AutomationDirect.com for details on how to plan

your installation for use of this powerful feature.

1 Align

with slot

2rotate

to seated

position

Module Installation

WARNING: Do not apply field power until

the following steps are completed. See

hot-swapping procedure for

exceptions.

WIRE STRIP

LENGTH

WIRE STRIP

LENGTH

Step One: Align module

catch with base slot and

rotate module into

connector.

Locked Unlocked

Step Two: Pull top locking tab

toward module face. Click indi-

cates lock is

engaged.

Step Three: Attach field wiring using the removable

terminal block or ZIPLink wiring

system.

Caution: If possible, remove field power prior to

proceeding. If not, then EXTREME care MUST be taken

to prevent damage to the module, or even personal injury

due to a short circuit from the live terminal block.

Sales 800-633-0405 www.productivity2000.com

Using the Hardware Configuration tool in the Productivity Suite

programming software, drag and drop the P2-8AD4DA-1 module into

the base configuration.

Select Automatic Module Verification or No Verification and Enable Hot

Swap. Also specify Input Resolution for inputs and Stop Mode Value for

outputs. If desired, assign a User Tagname to each input and output

point (channel) selected and to each Status Bit Item.

Module Configuration

Wiring Options

1ZIPLink Connection System

Cable + ZIPLink Module = Complete System

ZIPLink pre-wired

terminal block cables

0.5m (1.6FT) cable

1.0m (3.3FT) cable

2.0m (6.6FT) cable

ZIPLink Modules

Feed through

ZL-P2-CBL18

ZL-P2-CBL18-1

ZL-P2-CBL18-2

ZL-RTB20

2Terminal Block with pigtail cable

1.0m (3.3FT) cable

2.0m (6.6FT) cable

ZL-P2-CBL18-1P

ZL-P2-CBL18-2P

3Screw Terminal Block only

P2-RTB

(Quantity 1)

4Spring Clamp Terminal Block only

P2-RTB-1

(Quantity 1)

4Tech Support 770-844-4200www.productivity2000.com

Level Transmitte

ank Level

Select the Input and Output tags appropriate

for the application. Convert raw input signals

to engineering units for use in the program, or

convert engineering units to output signals for

control purposes

max

min

min max

12500

65535

220

1.55

2.25

4.55

6.75

6.5

Level Transmitte

ank Level

Select the minimum and maximum

values of the raw input signal.These

values will relate to the minimum

and maximum scaled values.

01 2 3 4 5 6 7

The Scale (Linear) function can be used to:

• Convert analog field input signals from the range which is native to the

analog input module to an application specific range.

• Convert an application specific range to a range which is native to the

analog output module.

• Make other linear conversions in ranges appropriate to the application.

The Scale (Non-Linear) function can be used for Non-Linear applications.

Linear Scaling Non-Linear Scaling

Sales 800-633-0405 www.productivity2000.com

Note: SPARE denotes deselected channel

Momentarily Press

SEL button to

toggle through

secondary displays

Hold SEL button down to cycle through primary screens. Release button to select screen.

Power On

Appears

initially

These screens will

then auto cycle

Error Messages –

An existing error will

be inserted into the cycling Status Info screen

This screen will

auto cycle with

status information

Fault Messages –

Appear

in place of data during a

fault condition.

On if input is

greater than or

equal to 20 mA.

On if input is

less than or

equal to 0 mA.

PASSED

SELF

TEST

P2-

8AD4DA-1

Fw. Rev.

1.00

In:

0-20mA

Out:

4-20mA

Channels

Enabled:

DISPLAY

SETUP

INFO

DISPLAY

STATUS

INFO

DISPLAY

UNITS

DECIMAL

COUNTS

DISPLAY

UNITS

HEX

COUNTS

DISPLAY

UNITS

End of

Status

List

MISSING

EXTERNAL

24VDC

SELFTEST

FAIL

REPLACE

MODULE

End of

Status

List

MISSING

CONFIG

DATA

1I00000

2I00000

3I00000

4I00000

5I00000

6I00000

7I00000

8ISPARE

1I00000

2I00000

3I00000

4I00000

5I00000

6I00000

7I00000

8ISPARE

1O00000

2O00000

3O00000

4O00000

1I0000H

2I0000H

3I0000H

4I0000H

5I0000H

6I0000H

7I0000H

8ISPARE

1I0000H

2I0000H

3I0000H

4I0000H

5I0000H

6I0000H

7I0000H

8ISPARE

1O0000H

2O0000H

3O0000H

4O0000H

1I00.0mA

2I00.0mA

3I00.0mA

4I00.0mA

5I00.0mA

6I00.0mA

7I00.0mA

8ISPARE

1I04.0mA

2I04.0mA

3I04.0mA

4I04.0mA

5I04.0mA

6I04.0mA

7I04.0mA

8ISPARE

1O04.0mA

2O04.0mA

3O04.0mA

4O04.0mA

1IOVER

2IUNDER

OLED Panel Display

8Tech Support 770-844-4200www.productivity2000.com

Document Name Edition/Revision Date

P2-8AD4DA-1-DS 1st Ed. 3/9/2015

WARNING: To minimize the risk of potential safety problems, you should follow all

applicable local and national codes that regulate the installation and operation of

your equipment. These codes vary from area to area and it is your responsibility

to determine which codes should be followed, and to verify that the equipment, in-

stallation, and operation are in compliance with the latest revision of these codes.

Equipment damage or serious injury to personnel can result from the failure to

follow all applicable codes and standards. We do not guarantee the products

described in this publication are suitable for your particular application, nor do

we assume any responsibility for your product design, installation, or operation.

If you have any questions concerning the installation or operation of this equip-

ment, or if you need additional information, please call Technical Support at

770-844-4200.

This publication is based on information that was available at the time it was

printed. At AutomationDirect.com®we constantly strive to improve our products

and services, so we reserve the right to make changes to the products and/or

publications at any time without notice and without any obligation. This publication

may also discuss features that may not be available in certain revisions of the

product.

Removable Terminal Block Specifications

Part Number P2-RTB P2-RTB-1

Number of

positions 18 Screw Terminals 18 Spring Clamp Terminals

Wire Range

30 - 16 AWG (0.051 - 1.31 mm²)

Solid / Stranded Conductor

3/64 in. (1.2 mm) Insulation Maximum

1/4 in (6 - 7 mm) Strip Length

28-16 AWG (0.081 - 1.31 mm²)

Solid / Stranded Conductor

3/64 in (1.2 mm) Insulation Maximum

19/64 in (7 - 8 mm) Strip Length

Conductors “USE COPPER CONDUCTORS, 75ºC” or equivalent.

Screw Driver

Width 1/8 in (3.8 mm) Maximum

Screw Size M2 N/A

Screw Torque 2.5 lb·in (0.28 N·m) N/A

Inhaltsverzeichnis

Andere Automationdirect.com E/A-System Handbücher

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08NE3 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08AD-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-06RTD Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-32NE3 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-07B Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 200 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Stride SIO-MB08THMS Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16NE3 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-04ADL-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-16NE3 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08ADL-1 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-08NE3 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-04RTD Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16NA Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-4ADL2DAL-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-15CDD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Stride SIO-MB04THMS Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16ADL-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-08NA Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08ADL-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16ADL-1 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08NAS Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-04AD Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

WAGO

WAGO I/O SYSTEM 750 750-833 Bedienungsanleitung