AUTOTECH 10.129.020K-021 Bedienungsanleitung

Installation Instructions

Part Number: 10.129.020K-021

Description: SCHRICK variable geometry intake manifold for VR6 engines

Notes:

The installation of the SCHRICK variable intake manifold is similar to that of the standard manifold. Some additional work

need to be done, compared to the standard intake manifold, due to the 3 part design of the variable resonance system.

Procedure:

1. Switch off ignition

Disconnect battery

2. Remove existing intake manifold

at this point it is recommended to install new spark plugs NGK BKR%EKUP

VW No 101 000 035 HA, which will last more than 60000km

3. Fit all spark plug connectors and tie the high tension ignition leads of the front cylinder bank with cable ties to the

injector rail.

4. Assemble the air distributor with gasket to the manifold. Torque the 3 M8 bolts to 15-20Nm

5. Assemble the throttle body to the air distributor. Torque the bolts to 15-20 Nm

6. Mount the accelerator cable bracket to the air distributor

Detach the noise damper of the idle control valve (where present) and connect the idle control valve directly to the air

distributor (see illus. 1)

7. Loosely mount the assembled intake manifold unit with standard gasket to the engine

8. Loosely mount the right hand manifold support on the exhaust side. Detach the left hand manifold support, it is no

longer required.

9. Torque the fastening bolts of the manifold and manifold-support to the 15-20Nm

10. Fasten the high tension ignition leads of the rear cylinder bank to the plastic brackets on the underside of the intake

manifold.

11. Connection of all outstanding components are similar to the standard intake manifold

12. Attach the accelerator cable

13. Secure the vacuum tank, solenoid valve and electronic control unit to appropriate areas. Because of the plastic content of

the parts it should only be ﬁtted to heat-protected areas.

14. Connect the vacuum hoses and rout it in an appropriate way. Connect the open end to the vacuum hose of the brake-

servo. (see illus. 2)

15. Connect the electronic control unit as follow:

a) connect plug to solenoid valve

b) red cable to switched + (15)

c) black cable to earth (chassis)

d) blue cable to rev-counter input signal

The rev-counter input signal can be allocated to different terminals / leads for different vehicle types. You will have to

determine which is the correct terminal / lead for your vehicle

16. the switching point of this control device is programmed for an engine speed of 4000 r.p.m. at which point the rising

engine speed causes the plenum valve ﬂap to open. The hysteresis is programmed for 50 r.p.m. so, that with falling engine

speed the plenum ﬂap valve closes at 3950 r.p.m. To set another switching pint, the control unit has to be opened. The

chosen switching point can be set by adjusting the switches (Protected by a waterproof ﬁlm) according to the attached

chart. After completion the switches must be sealed against water.

17. The battery may be connected after all electrical elements are properly connected, otherwise faults will be stored in the

engine electronics, which must be subsequently deleted by an authorized workshop.

18. Please note; Installation of the variable intake manifold will change the performance characteristics of the engine and

may therefore invalidate the vehicle registration documentation. A technical assessment at the responsible institution is

required.

Inhaltsverzeichnis

Andere AUTOTECH Autozubehör Handbücher

AUTOTECH

AUTOTECH 10.251.180K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.698.006K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.998.220K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.109.405K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.109.401K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.251.132K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.425.1632GK Bedienungsanleitung

AUTOTECH

AUTOTECH 10.430.210K211K213K215K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.109.055 Bedienungsanleitung

AUTOTECH

AUTOTECH 10.715.098K-099K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.109.402K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.411.01.219K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.998.221K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.998.230K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.109.418K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.698.005K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.525.1129K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.425.1725GK Bedienungsanleitung

AUTOTECH

AUTOTECH 10.425.1526GK Bedienungsanleitung

AUTOTECH

AUTOTECH 10.109.423 Bedienungsanleitung

AUTOTECH

AUTOTECH 10.251.134K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.611.208K-212K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.199.023K Bedienungsanleitung

AUTOTECH

AUTOTECH 10.941.060K Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung