Avital Diablo Bedienungsanleitung

Diablo2

/AMX 68/AT-58 Installation Manual 3/31/99

Downloaded from: http://www.guardianalarms.net

Table of Contents

Required Installation Tools.......................2

Important Information..........................2

Wiring Diagram..............................3

14 Pin Connector..............................4

Starter Disable Relay............................4

Installation Procedures..........................5

Control Unit................................5

Antenna..................................5

Wireloom..................................5

Zone

1Impact Sensor...........................5

Valet Switch................................6

LED Indicator...............................6

Ignition Input................................6

Channel 2 Accessory Output........................6

Parking Lights...............................6

Interior Light Trigger...........................7

Optional Interior Light Illumination Output................7

Starter Disable...............................7

Two Pulse Unlock.............................8

Door Lock/Unlock Outputs........................8

Hood/Trunk Pin Switch..........................8

Siren....................................8

Power and Ground Connections.....................8, 9

Door Lock Diagrams..........................9-11

Programming Alarm System Features.................12

Programming Table for Alarm Features.................12

Programming Your Remote Controls.................13

Programming Table for Remote Controls................13

Diablo

/AMX 68/AT-58 Installation Manual 3/31/99

Required Installation Tools

Voltmeter

Wire Strippers

Electric Drill & Bits

Phillips Screw Driver

Convoluted Tubing *

Solder Gun *

Wire Crimpers

Shrink Tube or Electrical Tape * Optional

Important Information

1.Test all circuits with a voltmeter.

2.Make all wiring connections with butt connectors. DO NOT twist wires

or use “scotch-lok” connectors.

3. Route RED, RED/WHITE and BLACK wires from the control unit

directly to the battery.

4. Keep extensions as short as possible. Use same gauge wires.

5.Before installing, discuss the placement of the LED indicator and valet

switch with the vehicle owner. DO NOT disconnect the battery cables.

6.Make all connections by removing the lug from the cable clamp

without detaching clamp.

7. Turn off dome light or remove dome light fuse to prevent battery drain.

This device complies with Part 15 of the FCC rules. Any changes or

modifications made to the system without the express approval of Avital

Technologies, Inc. could void the user's authority to operate this

equipment.

Diablo

/AMX 68/AT-58 Installation Manual 3/31/99

Wiring Diagram

Diablo

/AMX 68/AT-58 Installation Manual 3/31/99

Diablo2

/AMX 68/AT-58 Installation Manual 3/31/99

14 Pin Connector

Wire colorDescription

Red/WhiteParking Light Polarity Select (+) or (-)

Red/Black Parking Light Output

RedBattery (+)

Gray(-) Armed Output for Starter Disable Relay

BlackBattery (-)

Violet Siren (-) Output

TanHood/Trunk (-) Input

White/BlackInterior Light Illumination (-) Output/Requires Optional Relay

Dark BlueChannel 2 (-) Accessory Output

White Door Trigger Input (+) or (-)

PinkIgnition Switched +12 Volt Input Pre-wired to Starter Disable Relay

Blue/White (-) Door Lock Output

Green/White (-) Door Unlock Output

Starter Disable Relay

Wire colorDescription

14 Ga Yellow Starter Disable Ignition Switch Side

14 Ga YellowStarter Disable Starter Solenoid Side

Installation Procedures

Control Unit

1.Select a location under the dash that will allow you to use the tie wraps

to securely fasten the control unit.

2.Mount the control unit as high as possible to ensure maximum range.

3.Do not mount the control unit near moving parts.

4.Avoid areas that are in the direct path of air blowing from the vents.

5.Route wires from this point, leaving slack for ease of service.

Antenna

1.Do not shorten or lengthen the antenna.

2.Route the antenna away from the control unit.

3.Keep the antenna as far away from metal and wire harnesses as possible

to optimize range.

Wireloom

1. Plug the wireloom securely into the control unit.

2. Route wires from the control unit directly to each connection point.

3.Separate the RED, RED/WHITE, BLACK, VIOLET and TAN wires.

4.Sleeve the wires with vinyl tubing or electrical tape and route them

through an existing rubber grommet into the engine compartment.

5.If an existing grommet is not available, drill a hole and install a snap

grommet.

Zone

1  Impact Sensor

The sensor must be firmly mounted on a solid metal surface inside the

vehicle. We recommend tie wrapping the sensor to the steering column

housing or steering column support bracket. DO NOT mount the sensor near

moving parts or in the direct path of an air duct opening.

1.Plug the impact sensor BLUE 4 pin connector into the control unit

BLUE 4 pin connector.

2.Route the impact sensor to the chosen mounting location.

3.Using the supplied long tie wraps, securely fasten the impact sensor

allowing access to the adjustment screw.

Diablo2

/AMX 68/AT-58 Installation Manual 3/31/99

Valet Switch

1.Discuss placement with the owner.

2. Choose a location for the valet switch that is hidden, but convenient for

the owner to access.

3.Drill a ¼" hole and mount the switch.

4. Route the valet switch wires to the control unit.

5.Plug the valet switch WHITE connector into the control unit WHITE

plug.

LED Indicator

1.Discuss placement with the owner.

2. Choose a location that is visible from both sides of the vehicle.

3.Drill a ¼" hole.

4. Route the LED wires through the hole and press LED into place.

5.Route the LED wires to the control unit.

6.Plug the RED LED connector into the control unit RED plug.

Ignition Input

1.Use a voltmeter to locate the one wire that shows +12 volts when the

ignition key is in the "ON," "CRANK" and "RUN" position, and 0 volts

when the ignition key is in the "OFF" position.

2.Connect the control unit PINK wire to the vehicle’s ignition wire.

Channel 2 Accessory Output

The DARK BLUE wire provides a 0.75 second ground (-) output when the

remote control button #2 is activated for 1-2 seconds. If the remote control

button #2 is continuously pressed, the signal will stay at ground as long as the

button is held. Most trunk releases are positive and require an optional relay.

Parking Lights

1.If the parking lights are positive trigger, connect the RED/WHITE wire

to the battery positive (+) terminal through the 20 amp fuse.

NOTE: Do not connect the RED/WHITE wire to the control unit RED wire.

2.If the parking lights are negative (-) trigger, connect the RED/WHITE

wire to control unit BLACK wire.

3. Connect the RED/BLACK wire to the vehicle parking light wire.

Diablo2

/AMX 68/AT-58 Installation Manual 3/31/99

Interior Light Trigger

The Diablo2

interior light trigger wire is programmable to accept a positive

(+) or negative (-) input. The module is factory preset for negative (-) door

trigger.

1. Connect the alarm WHITE wire to the vehicle door trigger wire(s).

2.If the vehicle door trigger is positive (+) trigger, follow the "Door

Trigger Input Polarity" section in the "Programming Table for Alarm

Features"to program the module for positive (+) door trigger.

Optional Interior Light Illumination Output

The WHITE/BLACK wire provides a current limited (-) output for 30

seconds upon remote disarm. Interior light illumnination requires an

optional relay.

1.Connect the alarm WHITE/BLACK wire to relay terminal 85.

2.Connect relay terminal 86 to a fused constant +12 volt source.

3.Connect relay terminal 30 to the vehicle door trigger wire(s).

4.If the vehicle door trigger is positive (+) trigger, connect relay terminal

87 to a fused +12 volt source.

5.If the vehicle door trigger is negative (-) trigger, connect relay terminal

87 to ground (-).

Starter Disable

Make sure the YELLOW relay wires are solidly connected. The starter

circuit may draw very high current. We recommend that all connections be

soldered.

1.Locate the ignition switch wireloom under the dashboard.

2.Use a voltmeter to find the one wire that will show +12 volts while the

ignition key is in the "CRANKING " cycle only. This should be the

starter solenoid wire.

3. Cut the starter solenoid wire. Test by trying to crank the starter with the

ignition key. If it does not crank, you have the correct wire.

4.Connect one YELLOW wire to the key side.

5.Connect the other YELLOW wire to the starter side.

Diablo2

/AMX 68/AT-58 Installation Manual 3/31/99

Two Pulse Unlock

Some vehicles require two pulses to unlock the doors. The alarm can be

programmed to pulse the unlock wire two times when the alarm is remotely

disarmed. (See "Programming Alarm System Features" on page 12.)

Door Lock/Unlock Outputs

The alarm provides a .75 second 300 MA (-) output for lock and unlock.

Follow the door lock diagrams on pages 9 - 11.

Hood/Trunk Pin Switch

1.Locate the vehicle hood or trunk pin switch that shows ground when

the hood or trunk is open only.

2.Connect the alarm module TAN wire to the vehicle hood or trunk

switch wire.

3.If the vehicle does not have a hood or trunk switch, install a pin switch

and connect it to the alarm module TAN wire.

Siren

1. Choose a location in the engine compartment away from high heat

engine components, moving parts and direct exposure to water.

2.Make sure the siren and siren wires cannot be seen or reached from

below the vehicle.

3.Mount the siren with the two self tapping screws to a solid metal

surface.

4.Connect the siren BLACK wire to the alarm module VIOLET wire.

5.Connect the siren RED wire to the alarm module RED wire.

Power and Ground Connections

Caution: Do not plug in the system fuses until the final step below.

1.Connect the alarm RED wire to one of the supplied fuse assemblies.

2.Connect the alarm RED/WHITE wire to the other fuse assembly (if the

vehicle parking lights are (+) positive).

3.Connect the fuse assembly(s) to one of the supplied 10mm ring

terminals.

Continued . . .

Diablo2

/AMX 68/AT-58 Installation Manual 3/31/99

4. Connect the alarm BLACK wire to the other 10mm ring terminal.

5.Remove the (+) and (-) battery bolts. Do not disconnect the battery

clamps.

6. Connect the empty fuse assembly(s) to the positive battery post.

7.Connect the alarm BLACK wire to the battery negative post.

8.Inspect all alarm wiring. Make sure all wires are connected.

9.Install the 5 amp fuse in the alarm module RED wire fuse assembly.

10.Install the 20 amp fuse in the alarm module RED/WHITE fuse

assembly (if the vehicle parking lights are positive).

Diablo2

/AMX 68/AT-58 Installation Manual 3/31/99

Negative Trigger Door Locks

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Avital Autoalarmanlage Handbücher

Avital

Avital AviStart 3100 Montage- und Bedienungsanleitung

Avital

Avital Avistart 4001 Bedienungsanleitung

Avital

Avital 4300 Bedienungsanleitung

Avital

Avital AMX7 Bedienungsanleitung

Avital

Avital 5303 Bedienungsanleitung

Avital

Avital AviStart 6000 Bedienungsanleitung

Avital

Avital AviStart 6001 Bedienungsanleitung

Avital

Avital AviStart 6000 Bedienungsanleitung

Avital

Avital AMX58 Bedienungsanleitung

Avital

Avital Tornado Bedienungsanleitung

Avital

Avital AviStart 3100 Bedienungsanleitung

Avital

Avital Diablo 2 Bedienungsanleitung

Avital

Avital Phoenix 2 Bedienungsanleitung

Avital

Avital 4103 Bedienungsanleitung

Avital

Avital 4105L Bedienungsanleitung

Avital

Avital Maxx 1 Bedienungsanleitung

Avital

Avital 4308L Bedienungsanleitung

Avital

Avital AviStart 3200 Bedienungsanleitung

Avital

Avital MAXX2 Bedienungsanleitung

Avital

Avital MAXX3 Bedienungsanleitung

Avital

Avital Remote Access Bedienungsanleitung

Avital

Avital Diablo2 Bedienungsanleitung

Avital

Avital AviStar 3300 Bedienungsanleitung

Avital

Avital Hurricane Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung