AWS AMW-500i Bedienungsanleitung

American Weigh Scales, Inc.

User Manual

AMW-BENCH

Digital Tabletop Scale

AMW-500i

AMW-1000

ON/OFF

HoldModeTare

AMW-BENCH Manual

Thank you for purchasing the American Weigh AMW-

BENCH series digital tabletop scale. Please read

all operating instructions carefully before use. This

electronic scale is a precision instrument. With normal

care and proper treatment, it will provide years of

reliable service.

Never load the scale with more than the maximum

capacity. Overloading will permanently damage it!

Avoid any exposure to extreme heat or cold. Your

scale works better when operated at normal room

temperature. Always allow the scale to acclimate to

normal room temperature for at least one hour before

use. Give your scale sufcient warm up time. Usually

30-60 seconds before calibration to give the internal

components a chance to stabilize.

Keep your scale in a clean environment. Dust, dirt,

moisture, vibration, air currents and a close distance to

other electronic equipment can all cause an adverse

effect on the reliability and accuracy of your scale.

Handle with care. Gently apply all items to be weighed

onto tray top. Although this scale is designed to be

quite durable, try to avoid rough treatment as this may

permanently damage the internal sensor.

Avoid shaking, dropping or otherwise shocking the

scale. This is a precision instrument and must be

handled with extreme care.

Only operate the scale on a stable, vibration free

surface.

I. OPERATION

Place Scale on a horizontal at surface.

1. Press [ON/OFF] key.

2. Wait until "0.0” is displayed.

3. Put the object(s) on the weighing platform.

4. Using the [MODE] key, you can switch between the

weighing units.

II. TARE WEIGHING

1. Turn on scale as described above.

2. Place the "tare item" on the platform.

3. Press [TARE] and wait until "0.0" is displayed.

4. Add the "net-weight-item".

III. CALIBRATION

Calibration is NOT required before rst use. Only

calibrate if scale is not weighing properly.

**Make sure you use the correct calibration weight for

your scale or the calibration will not be accurate**

AMW-500i: 500g calibration weight

AMW-100: 2 (two) 500g calibration weights

a. AMW-500i Calibration Procedures

1. With the scale OFF, turn the scale upside down. Set the

switch on the underside of the scale to “CAL” and turn the scale

right side up again.

2. Press and hold the “On/Off” and “Mode” keys at the same

time until the display shows a random number. Release both

keys now.

3. Press the “On/Off” key once.

4. When the display reads “500 g”, place your 500g calibration

weight on the scale.

5. Press “On/Off” again. The display should read “PASS”.

You can now turn off your scale and return the switch under-

neath to “Normal”.

b. AMW-1000 Calibration Procedures

1. With the scale OFF, turn the scale upside down. Set the

switch on the underside of the scale to “CAL” and turn the scale

right side up again.

2. Press and hold the “On/Off” and “Mode” keys at the same

time until the display shows a random number. Release both

keys now.

3. Press the “On/Off” key once.

4. When the display reads “500 g”, place your 500g calibration

weight on the scale.

5. Press “On/Off” again.

6. The display will now read “1000 g”, place another 500g

calibration weigh on the scale to make a total of 1000 grams

on the scale.

6. Press “On/Off” once more, the display should read “PASS”.

You can now turn off your scale and return the switch under-

neath to “Normal”.

Please check the availability of weights with your scale

supplier.

IV. TROUBLESHOOTING

The primary reasons for inaccuracy or malfunction

are low batteries, incorrect calibration, overload or

operating on an unstable surface. Please keep this in

mind and maintain and operate your scale properly.

This scale is a precise instrument and must be

handled with the utmost care and caution.

[Display] Elimination of errors

Nothing, Battery-Symbol, [lo] or [88888]

Change the batteries.

[OUE2] Recalibrate the scale as shown above.

[EEEEE] You are overloading the scale. Remove the

excessive load immediately!

[LLLLL] The delicate weighing load cells have

been damaged by misusing the scale

(i.e. it was shocked, dropped or

overloaded). You can try recalibrating the

scale. If the load cell has not been

damaged too much it will work

again after recalibration.

[UNST] Use the scale in a more stable position

Specications

Model AMW-500i AMW-1000

Capacity 500g / 17.64oz / 16.08 ozt /

321.5dwt

1000g / 35.27oz / 32.15ozt /

643.1dwt

Resolution 0.1g / 0.01oz / 0.01ozt / 0.1dwt

Display 5 - Digit Backlit LCD

Calibration Weight

(not Included) 500g 2 (two) 500g

Platform Dimensions

(inches) 6 x 6 Stainless Steel

Scale Dimensions

(inches) 6.2 x 7.2 x 1.6

Power one 9V Battery (included) or AC-Adapter (sold seperate)

Gross Weight 1.63 lb

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AWS Skala Handbücher

Beliebte Skala Handbücher anderer Marken

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung

Fidelity Electronics

Fidelity Electronics G2e Bedienungsanleitung