AWS LS-110 Bedienungsanleitung
American Weigh Scales
LS-110 (110lb x 0.2lb)
User Manual
LS-110
Copyright © 2010 American Weigh Scales, Inc.
All rights reserved. Rev. 2.0
LS-110 Manual
Thank you for purchasing the American Weigh
LS-110 luggage scale. Please read all operating instructions
carefully before use. Scales are precision measuring devices
and should always be handled with proper care. To ensure
years of reliable service, keep these simple tips in mind:
• Do not exceed the scale’s maximum capacity.
Overloading your scale can permanently damage it!
• Avoid exposure to extreme heat or cold. Scales
perform best at normal room temperature. If
temperatures have changed dramatically, calibration
and adjustment may be necessary.
• Allow your scale to warm up for 30-60 seconds before
performing calibration and adjustment (if available).
• Store your scale in a clean, dry location. Dust, dirt,
and moisture can accumulate on the weighing
sensors and electronics causing inaccuracy or
malfunction.
• Avoid using your scale in close proximity to strong
radio wave emitting devices such as computers, cash
registers, and cordless phones.
• Alwaysweighonaatandlevelsurface,freefrom
vibrations and drafts. The corner of a room is usually
the most stable.
• Gently apply all items to be weighed. Do not drop
items onto the weighing platform.
• Avoid dropping your scale. The warranty does not
cover damage due to rough treatment or overload.
• Checkthebatteriesrstifyouarehavinganytrouble
with your scale. This simple step can remedy most
scale issues.
• Do not disassemble your scale. This product contains
no user serviceable parts.
I. Part List
1. Scale
2. Weighing Tray
3. AAA Batteries (x2)
II. Key Description
III. Battery Installation
1. Beforeusingthescaleforthersttime,check
the battery compartment and remove any plastic
insulation strips or packaging that may be in place to
prevent battery drainage during shipping/storage.
2. If you are replacing the batteries, make sure the
positive and negative contacts are properly aligned.
ON/OFF
TARE Key
ON/OFF
Lock
Positive Side
Facing Out
LS-110 Manual
IV. Operation
1. Set the ON/OFF Lock switch to the ON position and
then tap the key to turn the scale on.
2. Once the start-up process completes and the scale
goes to zero, you are ready to weigh.
3. Place the quantity to be weighed on the weighing
hook.
4. Once the weight has stabilized, a red light will
illuminate on the top of the scale and the LCD will
display HOLD above the weight.
5. The weight will remain on the display after the item
is removed from the hook. To re-zero the scale, tap
the key.
6. Once weighing is complete, hold the key to turn
the scale off then set the ON/OFF Lock switch to the
OFF position.
V. Changing the Unit of Measure
This scale can read in KG or LB. To change the weighing
mode, follow these instructions:
1. Tap the key to turn the scale on, then
immediatedly press the key again and hold it for
2-3 seconds until the weighing unit is displayed,
then release.
2. Now tap the key to change the weighing unit
between KG or LB.
3. After a couple of seconds the scale will enter normal
weighing mode.
• LS-110 Units: kg (kilogram) lb (pound)
VI. Using the Tare Feature
You can use this scale’s tare feature to subtract the weight
of an empty container or vessel for net weight determination.
NOTE: The weight of the container will subtract from the
available capacity.
1. Turn on the scale as described in Section IV.
2. Attach your tare item / empty container using
the hook and wait for it to stabilize (HOLD will be
displayed).
3. Tap the button. “0.0” will be displayed.
4. You can now add items to the container to obtain
just the weight of the contents.
5. When the container is removed the weight will be
held on the display. Press again to zero the scale.
VII. Calibration
Calibration and adjustment are performed at the factory.
However, the weighing range can shift slightly during
shipping. Also, due to changes in local acceleration of gravity
around the world, adjustment is recommended when moving
the scale from one location to another. To check calibration:
1. Place the required calibration weight on the scale
and note the displayed value.
2. If the displayed value is not within acceptable
tolerance (see chart on next page), adjustment is
required.
Model Acceptable
Tolerance (±)
Calibration
Weight
Recommended
Accuracy Class
LS-110 0.3kg 20kg OIML M2
VIII. Adjustment
1. Press the key to turn the scale on.
2. Once the LCD shows “8888” press the key sev-
LS-110 Manual
eral times until the inner code displays (~2680)
3. Press again.Thedisplaywillash“CAL”followed
by the required calibration weight (20kg).
4. Add the required weight. The display will show pass
and return to normal weighing mode.
5. Remove the weigh and press and hold the key to
turn the scale off. Calibration is complete!
IX. Troubleshooting
• Problem: Scale will not turn on
• Solution: Check the batteries and ON/OFF lock
• Problem: Display will not stabilize
• Solution: Make sure the weight is stable on the
hook and not shaking or swinging
• Problem: Displayed weight is inaccurate
• Solution: Perform a calibration adjustment
X. Error Codes
1. OUTZ - Zero range has shifted. Perform calibration
adjustment. If the problem persists, the load cell may
be permanently damaged due to overloading.
2. EEEEE - Maximum capacity exceeded. Remove the
extra weight to avoid damaging the load cell.
3. LLLLL - Load cell has been overloaded.
4. UNST - The scale is unstable. Use the scale in a
more stable position
XI. Specications
LS-110
Max. Capacity 110lb / 50kg
Readability 0.2lb / 0.1kg
Min. Capacity 0.6lb / 0.3kg
Power 2 x CR2032
Dimensions 1.4 x 6.0 x 4.8 in. (hook extended)
Hook Dimensions Gap: 1.2in / Throat: 1.2in
Warranty 10 Year Limited Warranty
Inhaltsverzeichnis
Andere AWS Skala Handbücher
AWS
AWS V2-500 Bedienungsanleitung
AWS
AWS NutriBalance-5000 Bedienungsanleitung
AWS
AWS SR-1KG Bedienungsanleitung
AWS
AWS VP-100 Bedienungsanleitung
AWS
AWS MERCURY PRO MPR-180 Bedienungsanleitung
AWS
AWS ME-5KG Bedienungsanleitung
AWS
AWS CH-501 Bedienungsanleitung
AWS
AWS H-110 Bedienungsanleitung
AWS
AWS BT-500 Bedienungsanleitung
AWS
AWS OM-200 Bedienungsanleitung
AWS
AWS AMW-500i Bedienungsanleitung
AWS
AWS BS-100 Bedienungsanleitung
AWS
AWS BT2 series Bedienungsanleitung
AWS
AWS QS-500 Bedienungsanleitung
AWS
AWS Gemini-20 Bedienungsanleitung
AWS
AWS 330ECO Bedienungsanleitung
AWS
AWS GeminiPRO Bedienungsanleitung
AWS
AWS ZT-150 Bedienungsanleitung
AWS
AWS LB-SERIES Bedienungsanleitung
AWS
AWS DIA-20 Bedienungsanleitung
