AWS BLADE V2 BL2-50 Bedienungsanleitung
American Weigh Scales
BL2-50 (50g x 0.01g)
BL2-100 (100g x 0.01g)
BL2-400 (400g x 0.1g)
User Manual
BLADE V2
Copyright © 2011 American Weigh Scales, Inc.
All rights reserved. Rev. 2.0
Blade V2 Manual
Thank you for purchasing the American Weigh Blade
v2 digital pocket scale. Please read all operating instructions
carefully before use. Scales are precision measuring devices
and should always be handled with proper care. To ensure
years of reliable service, keep these simple tips in mind:
• Do not exceed the scale’s maximum capacity. This
scale has integrated overload protection, but any
overload protection has its limits.
• Avoid exposure to extreme heat or cold. Scales
perform best at normal room temperature. If
temperatures have changed dramatically, recalibration
may be necessary.
• Allow your scale to warm up for 30-60 seconds before
performing calibration (if available).
• Store your scale in a clean, dry location. Dust, dirt,
and moisture can accumulate on the weighing
sensors and electronics causing inaccuracy or
malfunction.
• Avoid using your scale in close proximity to strong
radio wave emitting devices such as cordless phones.
• Alwaysweighonaatandlevelsurface,freefrom
vibrations and drafts. The corner of a room is usually
the most stable.
• Gently apply all items to be weighed. Do not drop
items onto the weighing platform.
• Avoid dropping your scale. The warranty does not
cover damage due to rough treatment or overload.
• Checkthebatteriesrstifyouarehavinganytrouble
with your scale. This simple step can remedy most
scale issues.
• Calibration should be checked and adjusted
occasionally as part of routine scale maintenance.
I. Part List
1. Scale
2. Cover/Expansion Tray (top and bottom)
3. AAA Batteries (x2)
II. Key Description
1. Power Key - Turns the scale on or off.
2. Mode Key - Changes the displayed unit of measure.
Enters calibration if pressed during startup (see VII)
3. Tare Key - Re-zeros the scale. Used to remove the
weight of a tray or container.
4. Backlight Key - Turns backlight on or off.
III. Battery Installation
Proper Battery Installation
1.
4.
3.
2.
g
Blade V2 Manual
Low batteries can cause inaccuracies in digital scales. If
youareexperiencingissueswithyourscale,rsttrynew
batteries. Most times, this will solve the problem.
1. Beforeusingthescaleforthersttime,check
the battery compartment and remove any plastic
insulation strips or packaging that may be in place to
prevent battery drainage during shipping/storage.
2. If you are replacing the batteries, make sure the
positive and negative contacts are properly aligned.
IV. Operation
1. Placethescaleonaat,levelsurfaceandpressthe
key to turn the scale on.
2. Once the start-up process completes and the scale
goes to zero you are ready to weigh.
3. Place the quantity to be weighed onto the weighing
platform.
4. Wait a couple seconds for the display to stabilize
before taking a weight reading.
5. To turn the scale OFF, press the key again.
V. Changing the Unit of Measure
1. Press the Mkey to change the scales displayed unit
of measure.
2. If the scale is turned off then back on, it will default
to the last unit used.
• Blade V2 Units: g (gram) oz (ounce) ozt (troy
ounce) dwt (pennyweight) ct (carat) gn (grain)
VI. Using the Tare Feature
You can use this scale’s tare feature to subtract the weight
of an empty container or vessel for net weight determination.
NOTE: The weight of the container will subtract from the
available capacity (subtractive taring).
1. Place the empty container or vessel on the weighing
platform.
2. Press the Tkey once. The display will then reset to
zero. If the container is removed, its weight will be
displayed as a negative number.
3. Youmaynowllthecontainerwiththequantityto
be weighed. The display will show the net weight of
the contents.
4. To return to normal weight display (gross weight),
remove any items from the weighing platform and
press the T key again to re-zero the scale.
VII. Calibration
Initial calibration is performed at the factory. However, the
calibration can drift slightly due to stresses from shipping.
Also, due to changes in local acceleration of gravity around
the world, adjustment is recommended when moving the
scale from one location to another. To check calibration:
1. Place the required calibration weight on the scale
and note the displayed value.
2. If the displayed value is not within acceptable
tolerance (see chart on next page), adjustment is
required.
Blade V2 Manual
Model Acceptable
Tolerance (±)
Calibration
Mass
Recommended
Accuracy Class
BL2-50 0.02g 50g OIML M2
BL2-100 0.02g 100g OIML M2
BL2-400 0.2g 200g OIML M2
VIII. Adjustment
1. Press the key to turn the scale on, then immediately
press and hold the M key until “CAL” is displayed
then release.
2. PresstheMkeyagain.Thedisplaywillash“CAL”
followed by the required calibration weight (see
above).
3. Place the required calibration weight on the center
of the weighing platform.
4. Oncetheweightisconrmed,thedisplaywillshow
“PASS” then return to normal weighing mode.
NOTE: Adjustment using the incorrect mass will
result in inaccurate readings.
IX. Troubleshooting
• Problem: Scale will not turn on
• Solution: Check the batteries and battery contacts.
• Problem: Displayedweightuctuatesrandomly
• Solution: Make sure your workspace is stable and
free of any air currents or vibration. In some cases,
nearby radio wave emitting devices can cause
uctuations.
• Problem: Displayed weight is inaccurate
• Solution: Perform a calibration adjustment. If
you are still having trouble, contact our warranty
department.
X. Error Codes
1. OUTZ - Zero point has drifted out of the acceptable
range. Try to perform a calibration adjustment. If the
problem persists, the load cell may be permanently
damaged due to overloading.
2. O-Ld - Overload. The maximum capacity has
been exceeded. Remove the extra weight to avoid
permanently damaging the load cell.
3. Lo - Batteries are low. Replace the batteries.
XI. Specications
BL2-50 BL2-100 BL2-400
Max. Capacity 50g 100g 400g
Readability 0.01g 0.01g 0.1g
Min. Weight 0.03g 0.03g 0.2g
Power 2 x 1.5V “AAA” Alkaline
Dimensions 2.9 x 2.9 x 0.7 in.
Platform Dimensions 2.8 x 2.8 in.
Warranty 10 Year Limited Warranty
Blade V2 Manual
American Weigh Scales, Inc.
Norcross, GA 30092
Made In China to our exact
specicationsandqualitycontrol.
XII. Capacity/Readability Charts
BL2-50 BL2-100
50g x 0.01g
1.76oz x 0.001oz
1.61ozt x 0.001ozt
32.15dwt x 0.01dwt
250ct x 0.05ct
771.6gn x 0.2gn
100g x 0.01g
3.527oz x 0.001oz
3.215ozt x 0.001ozt
64.30dwt x 0.01dwt
500ct x 0.05ct
1543.2gn x 0.2gn
BL2-400
400g x 0.1g
14.11oz x 0.01oz
12.86ozt x 0.01ozt
257.2dwt x 0.1dwt
2000ct x 0.5ct
6173gn x 2gn
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere AWS Skala Handbücher
AWS
AWS BCM-100 Bedienungsanleitung
AWS
AWS CITRON-5K Bedienungsanleitung
AWS
AWS GO-110 Bedienungsanleitung
AWS
AWS VANILLA-5K Bedienungsanleitung
AWS
AWS MSC-100 Bedienungsanleitung
AWS
AWS BT2 series Bedienungsanleitung
AWS
AWS ES-250 Bedienungsanleitung
AWS
AWS CP2-300 Bedienungsanleitung
AWS
AWS ME-5KG Bedienungsanleitung
AWS
AWS SR-1KG Bedienungsanleitung
AWS
AWS AMW-505 Bedienungsanleitung
AWS
AWS 330HRS Bedienungsanleitung
AWS
AWS TS-200 Bedienungsanleitung
AWS
AWS AC-650 Bedienungsanleitung
AWS
AWS AT-500 Bedienungsanleitung
AWS
AWS CP3-100 Bedienungsanleitung
AWS
AWS KG-10 Bedienungsanleitung
AWS
AWS JB-500 Bedienungsanleitung
AWS
AWS QUANTUM Montageanleitung
AWS
AWS EPSILON EP-5KG Bedienungsanleitung
