AWS V2-600 Bedienungsanleitung
V2-600 (600g x 0.1g)
User Manual
V2-600
Copyright © 2010 American Weigh Scales, Inc.
All rights reserved. Rev. 2.0
V2-600
Thank you for purchasing the American Weigh V2-600
digital pocket scale. Please read all operating instructions
carefully before use. Scales are precision measuring devices
and should always be handled with proper care. To ensure
years of reliable service, keep these simple tips in mind:
• Do not exceed the scale’s maximum capacity.
Overloading your scale can permanently damage it!
• Avoid exposure to extreme heat or cold. Scales
perform best at normal room temperature. If
temperatures have changed dramatically, calibration
and adjustment may be necessary.
• Allow your scale to warm up for 30-60 seconds before
performing calibration and adjustment(if available).
• Store your scale in a clean, dry location. Dust, dirt,
and moisture can accumulate on the weighing
sensors and electronics causing inaccuracy or
malfunction.
• Avoid using your scale in close proximity to strong
radio wave emitting devices such as computers, cash
registers, and cordless phones.
• Alwaysweighonaatandlevelsurface,freefrom
vibrations and drafts. The corner of a room is usually
the most stable.
• Gently apply all items to be weighed. Do not drop
items onto the weighing platform.
• Avoid dropping your scale. The warranty does not
cover damage due to rough treatment or overload.
• Checkthebatteriesrstifyouarehavinganytrouble
with your scale. This simple step can remedy most
scale issues.
• Do not disassemble your scale. This product contains
no user serviceable parts.
M T
I. Part List
1. Scale
2. Remote Indicator Mounting Hardware
3. AA Batteries (x2)
II. Key Description
III. Battery Installation
1. Beforeusingthescaleforthersttime,check
the battery compartment and remove any plastic
insulation strips or packaging that may be in place to
prevent battery drainage during shipping/storage.
2. If you are replacing the batteries, make sure the
positive and negative contacts are properly aligned.
Power ON/OFF
Tare Key
Mode Key
M T
V2-600
IV. Operation
1. Placethescaleonaat,levelsurfaceandpressthe
ON/OFF key to turn the scale on.
2. Once the start-up process completes and the scale
goes to zero you are ready to weigh.
3. Place the quantity to be weighed onto the weighing
platform.
4. Wait a couple seconds for the display to stabilize
before taking a weight reading.
V. Changing the Unit of Measure
1. Press the MODE key to change the scales displayed
unit of measure.
2. If the scale is turned off then back on, it will default
to the last unit used.
• V2-600 Units: g (gram) oz (ounce) ozt (troy
ounce) dwt (pennyweight)
VI. Using the Tare Feature
You can use this scale’s tare feature to subtract the weight
of an empty container or vessel for net weight determination.
NOTE: The weight of the container will subtract from the
available capacity.
1. Place the empty container or vessel on the weighing
platform.
2. Press the TARE key once. The display will then
reset to zero. If the container is removed, it’s weight
will be displayed as a negative number.
3. Youmaynowllthecontainerwiththequantityto
be weighed. The display will show the net weight of
the contents.
4. To return to normal weight display (gross weight),
remove any items from the weighing platform and
press the TARE key again to re-zero the scale.
VII. Calibration
Calibration and adjustment are performed at the factory.
However, the weighing range can shift slightly during
shipping. Also, due to changes in local acceleration of gravity
around the world, adjustment is recommended when moving
the scale from one location to another. To check calibration:
1. Place the required calibration weight on the scale
and note the displayed value.
2. If the displayed value is not within acceptable
tolerance (see chart below), adjustment is required.
Model Acceptable
Tolerance (±)
Calibration
Weight
Recommended
Accuracy Class
V2-600 0.2g 500g OIML M2
VIII. Adjustment
1. Press and hold the MODE key until the display
shows “CAL”.
2. Press the MODEkeyagain.Thedisplaywillash
“CAL” followed by the calibration weight value (see
chart).
3. Place the calibration weight on the center of the
weighing platform. Make sure you are using the
correctweightforyourspecicmodel.
4. Once the weight is accepted, the display will show
“PASS” then return to normal operation.
V2-600
IX. Troubleshooting
• Problem: Scale will not turn on
• Solution: Check the batteries
• Problem: Displayedweightuctuatesrandomly
• Solution: Make sure your workspace is stable and
free of any air currents or vibration
• Problem: Displayed weight is inaccurate
• Solution: Perform a calibration adjustment
X. Error Codes
1. OUTZ - Zero range has shifted. Perform calibration
adjustment. If the problem persists, the load cell may
be permanently damaged due to overloading.
2. 88888 - Maximum capacity exceeded. Remove the
extra weight to avoid damaging the load cell.
3. L - Batteries are low. Replace the batteries.
V2-600
Max. Capacity 600g / 21.16oz / 19.29ozt / 385.8dwt
Readability 0.1g / 0.01oz / 0.01ozt / 0.1dwt
Min. Weight 0.3g
Power 2 x AAA Batteries
Scale Dimensions 0.7 x 2.2 x 4.2”
Platform Dimensions 1.9 x 2.1”
Warranty 10 Year Limited Warranty
Inhaltsverzeichnis
Andere AWS Skala Handbücher
AWS
AWS NutriBalance-5000 Bedienungsanleitung
AWS
AWS PN-Series Bedienungsanleitung
AWS
AWS MERCURY MRC-200 Bedienungsanleitung
AWS
AWS AMW-150M Bedienungsanleitung
AWS
AWS LB-1000 Bedienungsanleitung
AWS
AWS AMW-500i Bedienungsanleitung
AWS
AWS H-11 Bedienungsanleitung
AWS
AWS PB-13 Bedienungsanleitung
AWS
AWS MC series Bedienungsanleitung
AWS
AWS CP5-100 Bedienungsanleitung
AWS
AWS NutriBalance-5000 Bedienungsanleitung
AWS
AWS mini PRO-30 Bedienungsanleitung
AWS
AWS PK-110 Bedienungsanleitung
AWS
AWS AT-500 Bedienungsanleitung
AWS
AWS TS-200 Bedienungsanleitung
AWS
AWS IDOL-100 Bedienungsanleitung
AWS
AWS TB-2610 Bedienungsanleitung
AWS
AWS JB-500 Bedienungsanleitung
AWS
AWS MSC-200 Bedienungsanleitung
AWS
AWS QS-500 Bedienungsanleitung
