AWS TS-200 Bedienungsanleitung
American Weigh Scales, Inc.
User Manual
TS-200
Digital Pocket Scale
TS-200
CAL
MODE
ON
OFF
200X0.1gram
g
TS-200 Manual
Thank you for purchasing the American Weigh TS-200
digital scale. Please read all operating instructions
carefully before use. This electronic scale is a
precision instrument. With normal care and proper
treatment, it will provide years of reliable service.
Never load the scale with more than the maximum
capacity. Overloading will permanently damage it!
Avoid any exposure to extreme heat or cold. Your
scale works better when operated at normal room
temperature. Always allow the scale to acclimatize to
normal room temperature for at least one hour before
use.
Give your scale sufcient warm up time. Usually
30-60 seconds before calibration to give the internal
components a chance to stabilize.
Keep your scale in a clean environment. Dust, dirt,
moisture, vibration, air currents and a close distance to
other electronic equipment can all cause an adverse
effect on the reliability and accuracy of your scale.
Handle with care. Gently apply all items to be weighed
onto tray top. Although this scale is designed to be
quite durable, try to avoid rough treatment as this may
permanently damage the internal sensor.
Avoid shaking, dropping or otherwise shocking the
scale. This is a precision instrument and must be
handled with extreme care.
Only operate the scale on a stable, vibration free
surface.
I. OPERATION
Insert batteries and place the scale on a at surface.
1. Press the [ON/TARE] key.
2. Wait until "0.0” is displayed.
3. Put the object(s) on the weighing platform.
4. Using the [CAL/MODE] key, you can switch
between different weighing units.
II. TARE WEIGHING
The Tare function subtracts the weight of a container.
1. Turn on scale as described above.
2. Place the "tare item" (container) on the platform.
3. Press [ON/TARE] and wait until "0.0" is displayed.
4. Add the "net-weight-item" (weight of contents only).
III. CALIBRATION
Calibration is not required before rst use. Only
calibrate if scale is not weighing properly.
1. Press [ON/TARE] to turn on the scale. Wait 30
seconds for the scale to warm up.
2. When the display shows "0.0" press and hold
[CAL/MODE] until the display ashes "AL"
3. Wait for about 5 seconds, the display will show "AL
0". Place a 100g calibration weight (not included) onto
the weighing tray.
4. Wait for about 5 seconds, if the display shows "AL
F", calibration is complete. It should return to normal
weighing mode.
5. If the scale shows "AL E" instead, an error has
occured. Repeat calibration.
Capacity 200g / 7.05oz / 128.6dwt / 6.43ozt
Resolution 0.1g / 0.01oz / 0.1dwt / 0.01ozt
Repeatability +/- 0.1g
Power two CR2032 Batteries
V. TROUBLESHOOTING
The primary reasons for inaccuracy or malfunction
are low batteries, incorrect calibration, overload or
operating on an unstable surface. Please keep this in
mind and maintain and operate your scale properly.
This scale is a precise instrument and must be
handled with the utmost care and caution.
[Display] Elimination of errors
[LO-] Replace the batteries.
[O-Ld] You are overloading the scale. Remove the
excessive load immediately!
[AL E] A calibration error has occured. If the
error coninues, the delicate load cells may
have been damaged.
Inhaltsverzeichnis
Andere AWS Skala Handbücher
AWS
AWS MB-50 Bedienungsanleitung
AWS
AWS CV-100 Bedienungsanleitung
AWS
AWS 330ECO Bedienungsanleitung
AWS
AWS mini PRO-30 Bedienungsanleitung
AWS
AWS AMW-13 Bedienungsanleitung
AWS
AWS EXTEND-5K Bedienungsanleitung
AWS
AWS PN-Series Bedienungsanleitung
AWS
AWS AMW-150M Bedienungsanleitung
AWS
AWS IDOL-100 Bedienungsanleitung
AWS
AWS SG-300 Bedienungsanleitung
AWS
AWS AT-500 Bedienungsanleitung
AWS
AWS Blade-50 Bedienungsanleitung
AWS
AWS DigiPEN-500 Bedienungsanleitung
AWS
AWS AMW-440T Bedienungsanleitung
AWS
AWS 330CVS Bedienungsanleitung
AWS
AWS MiniCD MCD-100 Bedienungsanleitung
AWS
AWS AWS-70 Bedienungsanleitung
AWS
AWS Chrome Bedienungsanleitung
AWS
AWS ZT-150 Bedienungsanleitung
AWS
AWS ME-5KG Bedienungsanleitung
