Axminster Craft AC125WDG Bedienungsanleitung
Code 105247
Original Instructions
AT&M: 20/08/2020
BOOK REF: APT008258
BOOK VERSION: 2
AC125WDG
Wet & Dry Grinder
Index of Contents
2
EU Declaration of Conformity
Fully read manual
and safety instructions
before use
Eye protection
should be worn
Ear protection
should be worn
HAZARD
Motor gets hot
Dust mask
should be worn
The symbols below advise the correct safety procedures when using this machine.
Cert No: SCM5800
Axminster Tool Centre Ltd
Axminster Devon
EX13 5PH UK
axminstertools.com
Type Wet & Dry Grinder
Model AC125WDG and conforms to the machinery example for which the
EC Type-Examination Certificate No WAR-18NO2370TTSHP
has been issued by Wendeng Allwin Motors Manufacturing Co., Ltd.
at: No.15 Sichan Road,Wendeng, Shandong,CHINA, 264400
and complies with the relevant essential health and safety requirements.
2006/42/EC
EN 62841-1:2015
EN 62841-3-4:2016
declares that the machinery described:-
This machine complies with the following directives:
EU Declaration of Conformity
Signed
Andrew Parkhouse
Operations Director Date: 14/03/2019
EU Declaration of Conformity 02
What’s Included 03
General Instructions for 230V Machines 04
Specific Safety Precautions for Grinding Machines 04-05
Assembly/Set-up 05-06-07
Specification 08
Illustration and Parts Description 09-10
Operating Instructions 10-11-12
Changing the 125mm Grinding Stone 13
Changing the 200mm Grinding Stone 14
Dressing the Stone 14-15
Ultimate Edge Accessories 15
Exploded Diagrams/Lists 16-17-18
Wiring Diagram 18
Notes 19
What’s Included
3
Quantity Model Number
AC125WDG
Quantity Item Part
1 Wet & Dry Grinder A
1 Eye shield & fixing screws, nuts B
1 Spark guard bracket & fixing screws C
1 Eye shield mounting bar D
1 Eye shield mounting bracket E
1 Threaded bolt F
1 Mounting bar square bracket G
1 Tool rest, nut & washer H
Quantity Item Part
1 Wet stone grinding stone I
1 Wet stone locking clamp J
1 Wet stone locking spanner K
1 Water container & regulator L
1 Universal support bar M
1 Square edge jig N
1 Universal support bar holder O
1 Support bar P
1 Water trough drain hose Q
BD
I
J
E
F G
C
K
L
AN
M
H
O P
Q
General Instructions for 230V Machines
4
The following will enable you to observe good working
practices, keep yourself and fellow workers safe and main-
tain your tools and equipment in good working order.
Mains Powered Tools
•Tools are supplied with an attached 13 Amp UK 3 pin plug,
fitted with 5 amp fuse.
•Inspect the cable and plug to ensure that neither are
damaged. Repair if necessary by a suitably qualified
person.
•Do not use when or where it is liable to get wet.
Workplace
•Do not use 230V a.c. powered tools anywhere
within a site area that is flooded.
•Keep machine clean.
•Leave machine unplugged until work is about to
commence.
•Always disconnect by pulling on the plug body
and not the cable.
•Carry out a final check e.g. check the cutting tool
is securely tightened in the machine and the
correct speed and function set.
•Ensure you are comfortable before you start work,
balanced,not reaching etc.
•Wear appropriate safety clothing, goggles, gloves,
masks etc.Wear ear defenders at all times.
•If you have long hair wear a hair net or helmet to prevent
it being caught up in the rotating parts of the machine.
•Consideration should be given to the removal of rings
and wristwatches.
•Consideration should also be given to non-slip
footwear etc.
•If another person is to use the machine, ensure they are
suitably qualified to use it.
•Do not use the machine if you are tired or distracted.
•Do not use this machine within the designated safety
areas of flammable liquid stores or in areas where there
may be volatile gases.
•Check cutters are correct type and size,are
undamaged and are kept clean and sharp, this will
maintain their operating performance and lessen the
loading on the machine.
•OBSERVE…. make sure you know what is
happening around you and USE YOUR COMMON SENSE.
WARNING!! KEEP TOOLS AND
EQUIPMENT OUT OF REACH OF
YOUNG CHILDREN
KEEP WORK AREA AS
UNCLUTTERED AS IS PRACTICAL.
UNDER NO CIRCUMSTANCES
SHOULD CHILDREN BE ALLOWED
IN WORK AREAS.
Specific Safety Precautions for Grinding Machines
1. Do not operate your machine until it is completely
assembled and installed according to the instructions.
2. If you are not familiar with the operation of grinding
machines, obtain advice from your supervisor or instructor
or another qualified person.
3. Only use grinding wheels or attachments rated higher
than 3600 rpm with a 5/8”(16mm) arbor on the left hand
stone station on this machine.
4. Never use a chipped or cracked wheel. Always inspect
each wheel before mounting it on the grinder. If during
inspection you discover a damaged grinding wheel, replace
it immediately.
5. Do not over tighten wheel nuts.
6. Always maintain a distance of 2mm or less between the
wheel and the tool rest. Adjust the tool rests as the wheels
decrease in size.
7. Ensure the tool rests are tightened so they cannot move
while in use.
8. Never grind on a cold wheel.The grinder should always
be run for at least one minute before applying work to it.
9. Never grind on the side of the wheel. Always grind on
the face of the wheel only.
10. Never apply coolant directly to a grinding wheel, it may
cause the bonding to fail. If the work piece becomes hot,
dip it into a water pot to cool it down.
11. Hot sparks are a hazard! Never carry out grinding
operations near flammable gas or liquid.
Specific Safety Precautions for Grinding Machines
5
12. Always make sure the spark guards and eye shields
are in place,that they are properly adjusted and secured.
13. Keep the spark guards close to the wheels and
re-adjust them as the wheels wear.
14. Ensure the soft washer and the flanges furnished with
the grinder are used to mount any attachments (grinding
wheels, wire brushes, buffing wheels, etc) onto the shaft.
15. Always stand to one side of the grinder when starting
the machine.
16. Avoid awkward hand positions where a sudden slip
could cause the hands to come into contact with a grinding
wheel, wire brush etc.
17. If the wheel requires dressing,dress only the front of
the wheel, do not dress the sides.
Assembly/Set-up
1 4
5
6
2
3
H
E
C
D
B
P
Clamping
grub screw
Machined
face
Continues Over...
Set the spark guard so it just clears grinding stone
Assembly/Set-up
6
710
8
9
11
12
Check the stone is level &
seated correctly
Lock
O
I
K
J
L
P
Assembly/Set-up
7
Check the universal support bar holder (O)
is level and adjust until correct
Nip up the two clamping knobs to secure
the universal support bar (M) in place
Place a digital level or other to check the universal
bar is level and adjust if required
13
14
16
17
O
Q
M
18
19
N
Specification
8
Illustration and Parts Description
Code 105247
Model AC125WDG
Rating Craft
Power 250W 230V 50Hz 1Ph
Wheel Speed (Dry/Wet) 2,850rpm/230rpm
Grinding Wheel Diameter (Dry) 125mm
(Wet) 200mm
Grinding Wheel Width (Dry) 50mm
(Wet) 25mm
Overall L x W x H 400 x 370 x 380mm
Weight 17.5kg
Universal support bar
Water container
Water regulator
Wet stone
Square edge jig
Wet stone trough
Motor
Eye shield assembly
Support bar holder
On/Off switch
Tool rest
Stone guard
Bench mounting hole Water trough drain hose
Illustration and Parts Description
9
Water regulator.Twist the knob to regulate
how much water pours onto the wet stone.
Square edge jig & clamping knobs
Water outlet
Support bar holder
grub screw clamp
Support bar
grub screw clamp
Micro adjuster
Support bar holder
Clamping knob
Operating Instructions
10
WARNING! KEEP TOOLS AND
EQUIPMENT OUT OF THE REACH OF
YOUNG CHILDREN
CONNECT THE WET &
DRY GRINDER TO THE MAINS
SUPPLY.
ALWAYS WEAR EAR DEFENDERS
AND SAFETY GOGGLES.
Carry out final checks e.g. check the gap between the tool
rest and the stone is correct, check the stones are not badly
deformed (rounded edges,grooved face,etc; unless you
have specifically shaped the stone to these profiles), check
the eye shield is correctly positioned.Have a cooling pot
to hand if you need it. Fill the water container (L) to a level
about 15-20mm below the lip of the container, see fig 01
1
Fill with water
Container lip
2
Mark the bevel with a marker to allow you to see where
the grinding will occur.
The most common secondary bevel is 30° when the main
body of the tool is ground at 25°. The chart below gives
you some guidance as to which angle is most suited to
which materials.
Place the tool into the jig (N) around half way along the
blade and position it against the jig’s stops, see fig 3.
Tighten the clamping knobs. Slide the assembly onto the
universal bar (M), see fig 04.
3
4
Bevel edge chisels
Primary Bevel Secondary Bevel
20˚ Paring N/A
25˚ 12mm-50mm 27° - 30°
30˚ 6mm-10mm 32° - 35°
In general, secondary bevels can be between 2° and 5°
M
Stop
N
L
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Axminster Craft Schleifer Handbücher
