Axminster PROFESSIONAL AP50UE Bedienungsanleitung

AP50UE

Ultimate Edge Variable

Speed Sharpening System

Code 107658

Original Instructions

AT: 20/04/2022

BOOK VERSION: 7

Code 106686

Ultimate Edge

Angle Gauge Included

INDEX OF CONTENTS

The symbols below advise the correct safety procedures when using this machine.

Fully read manual

and safety instructions

before use

Eye protection

should be worn

Ear protection

should be worn

HAZARD

Dust mask

should be worn

EU DECLARATION OF CONFORMITY

Cert No: DC-P50

AxminsterTool Centre Ltd

Axminster Devon

EX13 5PH UK

axminstertools.com

Type Ultimate Edge

Model AP50UE conforms to the machinery example for which the

ECType-Examination Certiﬁcate No M.2016.201.N1187,14091705IDA 15001

has been issued by UDEM International Certiﬁcation Auditing

Training Centre Industry andTrade Co.Ltd

at:Mullukent Mahallesi 2073 Sokak (Eski 93 Sokak) No:10 Cankaya-Ankara-TURKEY

and complies with the relevant essential health and safety requirements.

2006/42/EC

2014/35/EU

EN ISO 12100:2010

EN ISO 60204-1:2006+AC:2010

declares that the machinery described:-

This machine complies with the following directives:

EU Declaration of Conformity

Signed

Andrew Parkhouse

Operations Director Date: 08/05/2022

EU Declaration of Conformity 02

What’s Included 03

General Instructions for 230V Machines 04

Speciﬁcation 04

Assembly 04-05-06-07

Illustration & Parts Description 08-09

Setup/Adjustment 10-11

Changing the Belt 12-13

Changing Motor Brushes/Maintenance 13

Support Bar with Dual Axis Adjustment 14-16

Support Bar Assembly 14

Setting the Support Bar 15

Setting the Bar to the Platen 16

Ultimate Edge Angle Gauge 16

Ultimate Edge Accessories 17-18-19-20-21

Polishing Compound Chart 22

Ultimate Edge OnlineVideo 23

Exploded Diagrams/List 24-25-26

Wiring Diagram 26

Spindle Speed Digital ReadoutTroubleshooting 27

WHAT’S INCLUDED

Quantity Item Part

1 Ultimate EdgeVariable Speed Sharpening System A

1 Abrasive Belt (Fitted) B

4 Adjustable Rubber Feet C

1 Graphite Pad (Self Adhisive) D

1 Long Hex Key 4mm E

1 Ultimate Edge Angle Gauge H

Model Number AP50UE

• Clamping Handle A

• Large Bolt B

• Four Caphead Screws C

• Large ClearWasher D

• Four SpringWashers E

• Round Bar F

• Adjustable Mounting Plate G

• Round Bar Mounting Plate H

• Mounting Plate Cradle I

Code 103738

Support Bar with Dual Axis Adjustment

GENERAL INSTRUCTIONS FOR 230V MACHINES

The following will enable you to observe good working

practices,keep yourself and fellow workers safe and maintain

your tools and equipment in good working order.

WARNING!! KEEP TOOLS AND EQUIPMENT

OUT OF REACH OF YOUNG CHILDREN

Mains Powered Tools

•Tools are supplied with an 13 Amp UK plug.

• Inspect the cable and plug to ensure that neither are

damaged.Repair if necessary by a suitably qualiﬁed person.

• Do not use when or where it is liable to get wet.

Workplace

• Do not use 230V a.c.powered tools anywhere

within a site area that is ﬂooded.

• Keep machine clean.

• Leave machine unplugged until work is about to commence.

• Always disconnect by pulling on the plug body and not the

cable.

•Carry out a ﬁnal check to the machine.

•Ensure you are comfortable before you start work,

balanced,not reaching etc.

•Wear appropriate safety clothing,goggles,gloves,

masks etc.Wear ear defenders at all times.

•If you have long hair wear a hair net or helmet to prevent it

being caught up in the rotating parts of the machine.

•Consideration should be given to the removal of rings and

wristwatches.

•Consideration should also be given to non-slip footwear etc.

•Do not use the machine if you are tired or distracted

•Do not use this machine within the designated safety areas

of ﬂammable liquid stores or in areas where there may be

volatile gases.

•OBSERVE…. make sure you know what is happening

around you and USE YOUR COMMON SENSE.

KEEP WORK AREA AS UNCLUTTERED AS IS

PRACTICAL. UNDER NO CIRCUMSTANCES SHOULD

CHILDREN BE ALLOWED IN WORK AREAS.

Code 107658

Model AP50UE

Rating Professional

Power DC 230V 50Hz 560W

Motor Speed 3,000 rpm

Motor Pulley Diameter 56 mm

Belt Speed (Metres Per Minute) 202-600 mpm

Belt Size 50 mm x 785 mm

Dust Extraction Outlet 32 mm

Overall L xW x H 420 x 280 x 480 mm

Weight 17.5 kg

SPECIFICATION

Assembly

Fig A

Domed Hex screws

ASSEMBLY

Threaded Rubber Feet

Locate the four‘Rubber Feet’(C),remove one nut from each

of the threaded feet and place aside.Slot each threaded foot

through the four pre-drilled holes to each corner of the unit’s

base.Replace the nuts,stand the unit upright and adjust each

foot in turn until the machine is level,see ﬁg 01-02.

Fig 01-02

Continues over...

Fig B

Control box assembly

Press knob in and twist

Lock

Unlock

Fig 03-04-05

ASSEMBLY

Locate the‘Graphite Pad’,(D) and peel off the adhesive backing.

Position the pad down onto the platen and press ﬁrmly down,

see ﬁg 10-11-12.

Rotate the lever (2) to the side of the platen,see ﬁg 06-07.

Press down the lever to release the belt tension,see ﬁg 08.

Fig 06-07

Fig 08

3. Remove the belt and place safely aside,see ﬁg 09.

Fig 09

Fitting the Graphite Pad

There are two options that can be ﬁtted to the‘Platen’.

• The‘Platen’on its own

• The‘Graphite Pad’which is included

For most applications we recommend the ﬁtting of the graphite

pad ,the graphite pad has a self adhesive backing and is stuck

directly onto the front face of the platen.

The graphite pad helps reduce friction between the abrasive

belt and the platen,it also helps with smoother grinding as has

a slight cushion effect between the item being sharpened and

the abrasive belt.

There may be some applications where a more rigid grind is

needed and would recommend to use the platen with no pad

ﬁtted.

ASSEMBLY

Fig 10-11-12

5. Slide the belt back on and centre the belt on the platen.

Press the lever (2) down and hold in place,pull the locking‘PIN’

(3) out and raise the platen to re-tension the belt,see ﬁg 13.

6. Close the belt access door and engage the locking pin,

see ﬁg 14-15.

Fig 13

Fig 14-15

ILLUSTRATION & PARTS DESCRIPTION

Belt Guard

Locking knob

Belt door

Base plate

Adjustable rubber foot

Belt tracking knob

Main ON/OFF switch

Motor

Control box

Motor brush cap

Motor brush access cap

Belt

Work table

Belt tension mechanism

32mm Lower dust

extraction outlet

32mm Upper dust

extraction outlet

Locking pin

ILLUSTRATION & PARTS DESCRIPTION

Locking pin for tension mechanism (A), Tracking control knob

(B), Operating lever (C) to release the tenstion to the belt

32mm Lower dust extraction outlet (F)

Belt tension mechanism

Foward/Reverse selector switch

Belt speed (MPM)

Meters Per Minute

Speed control dial

ON/OFF buttons

Main ON/OFF switch

SETUPADJUSTMENT

Tracking the Belt

CONNECT THE MACHINE TO THE

MAINS SUPPLY!

1. Press the main ON/OFF on switch to the‘ON’position,

see ﬁg 21.

2. Move the selector switch to the‘Forward’position,see ﬁg 22.

3. Make sure the speed control dial is turned right down then

press the‘GREEN’button to start the machine,see ﬁg 23.The

digital diaplay will read ‘For’(Forward) then‘202’(MPM) will

light up,see ﬁg 24-25.

Fig 21-22-23-24-25

4. Turn the speed control knob until the display reads around

‘400’(MPM),see ﬁg 26 Fig 23

Switch ON

Power ON

Selector switch in the

forward position

Forward

202 (MPM)

Increase

speed

Inhaltsverzeichnis

Andere Axminster Werkzeuge Handbücher

Axminster

Axminster ujk 106843 Bedienungsanleitung

Axminster

Axminster Woodturning Deluxe Pen Press Bedienungsanleitung

Axminster

Axminster Collet Chuck System Set Bedienungsanleitung

Axminster

Axminster Woodturner's Clubman & Goliath Chucks Bedienungsanleitung

Axminster

Axminster 504633 Bedienungsanleitung

Axminster

Axminster Pen Kit Bedienungsanleitung

Axminster

Axminster Digital Height Gauge Bedienungsanleitung

Axminster

Axminster Trade Series Bedienungsanleitung

Axminster

Axminster AW19FM Bedienungsanleitung

Axminster

Axminster Super Precision Woodturning Chuck Bedienungsanleitung

Axminster

Axminster Empress Pen Kits Bedienungsanleitung

Axminster

Axminster Pen Kit Bedienungsanleitung

Axminster

Axminster CSC500K Bedienungsanleitung

Axminster

Axminster UJK Cabinet & Recess Hinge Jig Bedienungsanleitung

Axminster

Axminster CSC500C Bedienungsanleitung

Axminster

Axminster Universal Sub Base Bedienungsanleitung

Axminster

Axminster 100714 Bedienungsanleitung

Axminster

Axminster WS1000TA Bedienungsanleitung

Axminster

Axminster AW19FM Bedienungsanleitung

Axminster

Axminster SIEG X1 Super Micro Mill Mk2 Bedienungsanleitung

Axminster

Axminster CrushGrind Shaft 195mm Bedienungsanleitung

Axminster

Axminster SIEG Super X2 Mill Bedienungsanleitung

Axminster

Axminster RTC7030 Bedienungsanleitung

Axminster

Axminster Router Elevator Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung