Babymoov A014201 Bedienungsanleitung

BC-63_Manual_05.pdf 1 22/7/14 6:10 pm

Thank you for purchasing our A014201 digital green baby monitor. Your unit

has been manufactured and checked under the strictest possible quality control to

ensure that each monitor leaves the factory in perfect condition. In the unlikely

event you find any defects or have any problem, please contact our dealer or

service center.

Please read this manual carefully to obtain maximum performance and

extended service life from the unit.

Features

- Full digital technique operating in the 902.000MHz---928.000MHz with zero

interference

- Automatic hop and search for free channel

- Operating range 800m in open space

- Low radiating power (only 10% of normal DECT or 50% of ECO DECT)

- Automatic power reduction system further reduce radiation level to 40% when

baby unit and parent unit are within close vicinity

- Talk back function on parent unit to soothe your baby

- Capable of using multiple baby units to monitor more babies

- Night light on baby unit with adjustable intensity level

- Baby’s room temperature indication on both baby and parent unit

- Battery status indicator and low battery alert on both baby and parent unit

- Digitally adjustable microphone sensitivity

- Audio and visual alert for out of range

- Audio and visual Hi/Lo temperature alert

- Digital volume control

- Vibration alert

- LED sound level meter

- Parent unit operate with Li rechargeable battery

- Sensor Touch Keys

WARNING

The A014201 should not be regarded as a medical device. Premature babies

or those considered to be at risk should be under the supervision of your doctor or

health personnel.

Direct supervision of your baby at a regular interval by a responsible adult is

strongly recommended in addition to using the A014201.

BC-63_Manual_05.pdf 2 22/7/14 6:10 pm

DIGITAL TECHNOLOGY AND APRS

This baby monitor employs full digital technology with zero interference.

The unit can automatically select free channel or hop to free channel during

communication to avoid interference from other electronic devices. In addition,

thanks to the Automatic Power Reduction System (APRS) which senses the signal

strength between the baby and parent unit and automatically reduces the emission

power from baby unit when the two units are in close vicinity. The level of radiation

to baby is greatly reduced.

POWER SUPPLY

(A) Baby Unit (BU)

1. Operation from batteries

Press down and slide open the battery door in direction as shown. Insert

three pieces AAA size (UM-4) alkaline batteries into the compartment.

Observe correct polarities indication.

N.B. For best performance, do not mix use old and new batteries or alkaline and

rechargeable batteries.

BC-63_Manual_05.pdf 3 22/7/14 6:10 pm

2. Operation using AC adapter

The unit can be operated on AC mains using the supplied 5V AC adapter.

Connect the output plug of adapter to USB port 16 , make sure the polari -

ty is correct. The power supply from the battery will be cut off once the

adapter’s output plug is inserted into USB port 16 .

(B) Parent Unit (PU)

1. Operation from battery pack

The Li polymer battery pack is already installed in the unit. To exchange

battery pack, remove belt clip and slide open the battery door in direction

as shown, take out the battery pack and disconnect from socket.

BC-63_Manual_05.pdf 4 22/7/14 6:10 pm

2. Charging up the Lithium rechargeable battery

Connect the output plug of supplied 5V AC adapter to USB port 37 of the

charger stand, make sure the polarity is correct. The unit can either be in

switch ON or OFF condition, place it into the charger stand. The charging

indicator 36 should light up white. Adjust the position of parent unit in

case the indicator 36 does not light up. During charging, the power on /

battery low icon 27 should be flashing red. Once the battery is fully

charged up, the power on / battery low icon 27 should stay steady

green. Either you can take it out or keep placing it in the charger stand will

cause no damage to battery. In the latter case, when the battery is being

consumed and voltage falls to a certain level, the charger stand will

automatically start charging up the battery again.

Note : Before using the parent unit for the first time, charge up the Li polymer

battery for at least three hours. It is recommended to switch off the unit during first

charging.

Even without the Li battery pack being installed, the unit can still oprate normally

once place in changer stand, while the power on icon 27 will always stay steady

green.

CAUTION : BESURE THE BATTERY IN PARENT UNIT IS RECHARGEABLE

TYPE BEFORE PLACING IN CHARGER STAND. OTHERWISE EXPLSION MY

RESULT .

BC-63_Manual_05.pdf 5 22/7/14 6:10 pm

PAIRING

This process is to match the parent unit with baby unit so that they can communicate with

each other while no other devices (even baby monitor of identical model) can interfere with

you or receiving your signal.

The baby and parent unit are already paired when they are shipped from factory. However,

we recommend to perform pairing process again in case interference is experienced or

when extra BU is added to work with the PU.

1. Press and hold the talk button 35 of PU.

2. Long press the power ON/OFF button 18 and wait until a starts flashing green.

Release both buttons 18 and 35 .

3. Long press the ON/OFF button 1 for 3 sec to switch on the BU. Now touch and

hold icon for 5 sec and wait until a show steady green while the BU number

icon 15 1or 2starts flashing green. Release the finger touching icon 15 . Perform

same to the other BU that can be purchased optionally.

4. Use the touch keys 2 3 to set the BU number to either 1 or 2. DO NOT set

both BU to same number or otherwise the system will not operate normally. Short

press the button 1 to confirm your setting, the BU number now show steady

while starts flashing.

steady

flashing

BC-63_Manual_05.pdf 6 22/7/14 6:10 pm

5. Now short press again the power ON/OFF button 1 of one BU. If pairing is

successful,the on both PU and BU should change steady green while two beep

sound is heard in PU with the corresponding BU number icon 33 or 34 being shown

up.

6.Shortpress button 1 oftheremainingBU,twobeepsoundisheardinPUwith

the flashestwotimesandthecorrespondingBUnumbershowup.The onthis

BU change from flashing to become steady green.

7.Longpress button 1 and 18 toswitchoffallBUandPUandthenswitchthem

on again, the baby monitor is now ready for operation.

8.IncaseBUandPUcannotcommunicatewitheachother,repeatpairingprocess

again.

N.B. IforiginallythereisonlyoneBUworkingwithPU,afterpurchasingthenew

extraBUatlaterstage,itisnecessarytoperformpairingprocessagainwithallthe

three units together.

BC-63_Manual_05.pdf 7 22/7/14 6:10 pm

1. Power ON/OFF button

2. Down touch key

3. Up touch key

4. Menu touch key

5. Night light touch key

6. Night light

7. Microphone

8. Temperature sensor

9. Room temperature indicator

10. Power on/battery low icon

11. Transmit icon

12. Microphone continuous on icon

13. Night light status icon

14. Speaker mute icon

15. BU number icon

16. USB power port

17. Speaker

18. Power ON/OFF button

19. Down touch key

20. Up touch key

21. Menu touch key

22. Vibrator touch key

23. Microphone

24. Speaker

25. Visual level meter

26. Room temperature indicator

27. Power on/battery low icon

28. Out of range/transmit icon

29. Vibration icon

30. Speaker mute icon

31. Temperature high limit icon

32. Temperature low limit icon

33. BU number 1 icon

34. BU number 2 icon

35. Talk button

36. Charging indicator

37. USB power port

CONTROLS LAYOUT

CHARGER STAND

BABY UNIT (BU)

PARENT UNIT (PU)

26 27

202122

1 5 4 3

BC-63_Manual_05.pdf 8 22/7/14 6:10 pm

OPERATION

Baby unit

1. Long press the power ON/OFF button 1 for 3 sec to switch on the unit. The power

on icon 10 as well as the assigned baby unit no. 15 should light up steady green

while the room temperature indicator 9 starts showing the baby’s room temperature.

To turn off, long press the button 1 again.

2. Place the unit about 1 m from the crib with the microphone 7 facing towards the

baby.

3. Short press the power ON/OFF button 1 to light up the touch key icons

( ). Touch and hold the menu icon 4 for over 2 sec to enteraa aa

programming mode, the microphone icon 12 will light up.

Adjust the microphone sensitivity by touching the up/down icon 2 and 3 such

that the unit will be set to transmit whenever the microphone 7 picks up a sound at

your desirable loudness level. The temperature indicator 9 will change during

adjustment. The higher the number, the more sensitive is the microphone 7 to

sound. There are total 5 levels of microphone sensitivity. When the maximum level is

reached, further touch of the up icon 3 will set the unit into continuous transmission

mode (i.e. the unit will transmit even without detecting a sound) and the icon 12

as well as transmission icon 11 will light up steady green. Short press the powera

ON/OFF button 1 to confirm your selection and exit from menu. Short touch of

menu icon 4 will show the setting of microphone sensitivity under standby mode.

4. Once the unit is in transmit mode, the transmit icon 11 will light up green. The

unit will return to standby mode a few seconds after the microphone 7 stops picking

up any sound and the transmit icon 11 will go off. Except when the unit is set in

continuous transmission mode, the transmit icon 11 will stay steady on.

5. The night light 6 can be set permanently ON by short touch of night light icon 5 .

Each touch of icon 5 will increase the level of light intensity with maximum 5

levels. When the maximum level is reached, further touch of icon 5 will set the

night light 6 into voice activated (VOX) mode. Under VOX mode, the icon 9

will light up and night light 6 will be switched on once the microphone 7 detects a

sound and automatically fade off a few seconds after the sound stops.

6. This baby monitor is equipped with talk back function so that parent can speak to baby

BU is set to continuous

transmission mode

VOX

BC-63_Manual_05.pdf 9 22/7/14 6:10 pm

Parent unit

1. Long press the power ON/OFF button 18 for 3 sec to switch on the unit. The

power on icon 27 should light up steady green while the temperature indicator

26 will show the baby’s room temperature within 10 sec. To turn off, long press the

button 18 again.

2. Setting of out of range alarm function and temperature alarm

a. Short press the power ON/OFF button 18 to light up the touch key icons

( ). Touch and hold the menu icon 21 for over 2 sec to enter

programming mode, the out of range/transmit icon will show up while the

temperature indicator 26 will show or flashing.

to comfort his/her emotion. Touch the up/down icons 2 and 3 to adjust the

volume of speaker 17 , temperature indicator 9 will change during adjustment. The

higher the number, the bigger is the loudness. There are total 5 levels of loudness.

When the minimum level is reached, further touch of the down icon 2 will totally

mute the speaker 17 volume and the speaker mute icon will show up.

7. The condition of the battery is shown by the power on/low battery icon 10 . When

the battery level becomes running low, the power on/low battery icon 10 turns

red. Replace with new battery or use the supplied AC adapter.

8. The temperature sensor 8 inside the unit detects the ambient temperature and its

current reading is shown on the temperature indicator 9 and 26 of both BU and

PU. Short press the power ON/OFF button 1 to light up the temperature indicator

9 . After 20 sec, it will go off automatically. The normal operating range of sensor is

-9℃ to +50℃. Temperature outside this range will be shown as - - . In case there is

a sudden big temperature change (e.g. you bring out the unit from indoor to outdoor

during winter time), the sensor may need to take a few minutes before it can settle to

the new environment and show the correct reading.

9. The touch keys will only have function when the icons ( ) are lighted up.

These icons will go off automatically in case no key is being touched for 5 sec to

avoid mishandling during daily usage.

N.B. Once the icons are lighted up, BU will not enter transmit mode until the icons go off.

10. Each time the icon keys are touched, a beep tone will be heard. To eliminate this

beep tone, touch and hold the down icon 2 for 2 sec until a second beep tone is

heard. To resume the beep tone, touch and hold the up icon 3 for 2 sec until a

beep tone is heard. Whenever the unit is switched off and then on again, the beep

tone will resume automatically.

BC-63_Manual_05.pdf 10 22/7/14 6:10 pm

Andere Handbücher für A014201

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere babymoov Babyphone Handbücher

babymoov

babymoov YOO Go Plus Bedienungsanleitung

babymoov

babymoov Simply Care Bedienungsanleitung

babymoov

babymoov A014011 Bedienungsanleitung

babymoov

babymoov A014012 Bedienungsanleitung

babymoov

babymoov Premium Care A014203 Bedienungsanleitung

babymoov

babymoov A014200 Bedienungsanleitung

babymoov

babymoov Simply Care Bedienungsanleitung

babymoov

babymoov Premium Care Bedienungsanleitung

babymoov

babymoov Babyphone Easy Care Bedienungsanleitung

babymoov

babymoov Babyphone Visio Care 2 Bedienungsanleitung

babymoov

babymoov Premium Care Bedienungsanleitung

babymoov

babymoov Yoo-See Bedienungsanleitung

babymoov

babymoov A014407 Bedienungsanleitung

babymoov

babymoov Babyphone Visio Care Bedienungsanleitung

babymoov

babymoov Babyphone Visio Care 2 Bedienungsanleitung

babymoov

babymoov Yoo-Travel Bedienungsanleitung

babymoov

babymoov YOO Master Plus 5 Bedienungsanleitung

babymoov

babymoov A014616 Bedienungsanleitung

babymoov

babymoov Babycamera 0% Emission Bedienungsanleitung

babymoov

babymoov A014010 Bedienungsanleitung

babymoov

babymoov YOO Care Bedienungsanleitung

babymoov

babymoov Premium Care Bedienungsanleitung

babymoov

babymoov Handy Care Bedienungsanleitung

babymoov

babymoov ULTIMATE CARE A014401 Bedienungsanleitung

Beliebte Babyphone Handbücher anderer Marken

Philips

Philips SCD 469 Bedienungsanleitung

Oricom

Oricom Babysense 7 Bedienungsanleitung

Levana

Levana TW502 Bedienungsanleitung

Luvion

Luvion Essential Bedienungsanleitung

Philips

Philips AVENT SCD841 Bedienungsanleitung

NUK

NUK Eco Control Video Display 550VD Bedienungsanleitung

Lorex

Lorex sweet peek mini Bedienungsanleitung

Mondevices

Mondevices MonBaby 2 Bedienungsanleitung

Famidoc

Famidoc FDBB-V2 Bedienungsanleitung

Graco

Graco iMonitor 2797 Bedienungsanleitung

Ramili

Ramili RV1000 Bedienungsanleitung

Philips

Philips SBC SC364 Bedienungsanleitung

Swann

Swann SW231-FLO Bedienungsanleitung

Badabulle

Badabulle Baby Online 300 m+ Bedienungsanleitung

Philips AVENT

Philips AVENT SCD526/00 Bedienungsanleitung

Uniden

Uniden Guardian UBR223 Bedienungsanleitung

Summer

Summer Day & Night 28470A Bedienungsanleitung

Ivation

Ivation Wireless Monitoring System Bedienungsanleitung

babymoov A014201 Bedienungsanleitung

Beliebte Babyphone Handbücher anderer Marken