Bacharach Monoxor II Bedienungsanleitung

MONOXOR II

INSTRUCTION 0019-9113

Portable CO Analyzer

Part No. 0019-7034 & 0019-7039

Rev. 8 - May 2010

Bacharach, Inc.

621 Hunt Valley Circle, New Kensington, PA 15068

PH: 1-800-736-4666 • FAX: 724-334-5001 • Web: www.mybacharach.com

E-mail: [email protected]

Printed in U.S.A. ® Registered Trademarks

WARRANTY

Bacharach, Inc. warrants to Buyer that at the time of delivery this Product will be free

from defects in material and manufacture and will conform substantially to Bacharach

Inc.’s applicable speciﬁcations. Bacharach’s liability and Buyer’s remedy under this

warrantyarelimitedtotherepairorreplacement,atBacharach’soption,ofthisProduct

orpartsthereofreturnedtoSelleratthefactoryofmanufactureandshowntoBacharach

Inc.’s reasonable satisfaction to have been defective; provided that written notice of

the defect shall have been given by Buyer to Bacharach Inc. within one (1) year after

the date of delivery of this Product by Bacharach, Inc.

Bacharach, Inc. warrants to Buyer that it will convey good title to this Product.

Bacharach’s liability and Buyer’s remedy under this warranty of title are limited to

the removal of any title defects or, at the election of Bacharach, to the replacement of

this Product or parts thereof that are defective in title.

All expendable items, such as electrochemical sensors, are warranted for a period of

six months.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND ARE GIVEN AND

ACCEPTED IN LIEU OF (I) ANY AND ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRAN-

TIES OF MERCHANTABILITYAND FITNESS FORAPARTICULAR PURPOSE:

AND (II) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY IN

CONTRACT OR TORT, WHETHER OR NOTARISING FROM BACHARACH’S

NEGLIGENCE,ACTUALORIMPLIED.TheremediesoftheBuyershallbelimitedto

those provided herein to the exclusion of any and all other remedies including, without

limitation incidental or consequential damages. No agreement varying or extending

the foregoing warranties, remedies or this limitation will be binding upon Bacharach,

Inc. unless in writing, signed by a duly authorized ofﬁcer of Bacharach.

Declaration of Conformity

Manufacturer's Name: Bacharach, Inc.

Manufacturer's Address: 621 Hunt Valley Circle

New Kensington, PA 15068

Product Name: MONOXOR II

Conforms to the following product speciﬁcations

EMC: European Directive 89/336/EEC

EN 500081-1 (Emissions)

EN 500082-1 (Immunity)

WARNING!

Because this instrument is used to detect and monitor materials and conditions which are

listedbyOSHAorothersaspotentiallyhazardousto personnel and property,theinformation

inthismanualmustbefullyunderstoodandutilizedtoensurethattheinstrumentisoperating

properly and is both used and maintained in the proper manner by qualiﬁed personnel. An

instrumentthatisnot properlycalibrated,operatedand maintained byqualiﬁedpersonnelis

likelyto provideerroneousinformation, whichcould preventuser awarenessofa potentially

hazardous situation for the instrument user, other personnel and property.

If, after reading the information in this manual, the user has questions regarding the op-

eration, application or maintenance of the instrument, supervisory or training assistance

should be obtained before use. Assistance is available by calling your nearest Bacharach

Service Center.

Figure 1. Monoxor II

1 INTRODUCTION

The Monoxor® II is a commercial-grade

portable instrument designed to display

concentrations of carbon monoxide (CO)

gasbetween0and2000 ppm.Thisinstru-

ment shows the presence of CO in a gas

samplebydrawingthesampleintoitssen-

sorchamberbyabuilt-inmotorizedpump.

Part#0019-7034comeswithaprobe.Part

#0019-7039 comes without a probe (All

non-probe related functions remain the

same in this instruction).

Other features and accessories of the

Monoxor II include: A large, back-lit

Liquid Crystal Display (LCD), which al-

lows the display to be read in any lighting

condition from direct sun-light to total

darkness; a semi-detachable elastic strap

that permits the instrument to be either

hand held, or hung on nearby objects; a

rigid stainless steel probe with handle,

connected to a ﬂexible hose that allows

gas samples to be taken from cramped

and conﬁned areas (alternate probes and

condensate traps may be used).

Figure 2. Battery

Installation

2 TECHNICALCHARACTERISTICS

CO Display Range ............... 0-1999 ppm CO

Accuracy.............................. ±10 ppm or ±5% of reading

whichever is greater*

Response Time..................... 90% of ﬁnal value within 40 sec.

Battery Requirements........... 1.5 V, “C” cells, Qty. 4

Operating Time** ................ 14 to 16 hours, alkaline cells

Operating Temp. Range ....... 23 to 104°F (–5 to 40°C)

Relative Humidity................ 10 to 85% non-condensing

Weight (w/o batteries).......... 12 ozs. (341 grams)

Dimensions .......................... 8.6 x 3.5 x 2.9 in. (218 x 89 x 74 mm)

To prepare the instrument for operation, you

must install four “C” size batteries, and (if

desired)installthehose and probe as described

in the following paragraphs.

For your convenience, and to ensure that the

instrumentwillprovidereliableCOindications,

the CO sensor is installed and the instrument

calibrated on 500 ppm of CO at the factory.

3.1 BatteryInstallation

Detachtheelasticstrap'smetalclipatthebottom

oftheinstrument,andslideoffthebatterycover

as shown in Figure2. Then while observing

proper battery polarity, install four “C” size

batteriesintothe instrument’s batterycompart-

ment. (Recommended battery types: Duracell

Alkaline or equivalent). After the batteries

are installed, replace the battery cover and the

elastic-strap clip.

* Tighter accuracy in the lower ranges, up to ±2 ppm, may be attained if

lower range calibration gases (eg. 100 ppm) are utilized.

** Times are with the backlight turned off. Continuous use of the backlight

will decrease battery life.

3 PREPARINGTHEMONOXORII

FOR OPERATION

Figure 3. Probe Installation

If batteries are accidently installed in the wrong polarity, a positive

temperaturecoefﬁcient(PTC)thermistorwillprotecttheinstrument’s

electronic circuitry. The instrument will operate once batteries are

properly installed and the PTC thermistor is allowed to cool.

3.2 ProbeInstallation

Install the probe by sliding the end of its tubing over the gas inlet

port on the top right side of the instrument as shown in Figure3. The

tubing may be difﬁcult to slide over the gas inlet port of the unit for

the ﬁrst time. This was done intentionally to allow for a snug ﬁt. If

necessary, use a little dish washing liquid diluted in water or heat the

end of the tube with hot tap water to help it slide onto the port.

GAS INLET PORT

LINE

DRYER

PROBE

HANDLE

When changing

probe tubes,

hand tighten nut,

and then use a

wrench to tighten

≈1 ﬂat to seal.

4 OPERATION

To operate the Monoxor II, you simply . . .

•Set its POWER switch to ON,

•Wait for the instrument to warm up (approx. 1 minute),

•Zero the display (if necessary),

•Take a gas sample.

Detailed operating procedures are presented below:

4.1 PowerON/OFF

TurnontheinstrumentbyslidingitsPOWERswitch

toON.Observethat when power is ﬁrst applied,all

numerical LCD segments are tested for 5–15 sec-

onds; after which, the LCD shows the detected CO level. (A minus

sign may appear during power up as the sensor stabilizes.) Turn off

the instrument by sliding the POWER switch to OFF.

Important!Whenstoringtheinstrumentforextendedperiodsoftime,

remove the batteries and ensure that the POWER switch is OFF. The

OFF position places a short across the CO sensor, thus keeping the

sensor from being destabilized while not in use.

4.2 ZeroingtheInstrument

After being turned on and warmed up for at least 1 minute, the instru-

ment should indicate 000 ±5 ppm in fresh air. If the instrument needs

to be zeroed, proceed as follows:

1. Ensure that the instrument is sampling air that is free of Carbon

Monoxide.

NOTE: If the instrument was zeroed in an area where CO was

present, a large negative CO display appears.

2. Using a 1/8" ﬂat-blade screwdriver, turn the

ADJUST potentiometer until the LCD shows

0 ppm.Thedisplayshowsnegativenumbersfor

zeroing purposes. An instrument can be considered zeroed with a

display bounce of up to ±3 ppm.

4.3 BacklightON/OFF

The LCD can be read in low-light areas by setting the front panel

LIGHT switch to ON.The backlight stays on until turned off, or until

the POWER switch is set to OFF.

4.4 UsingtheStrap

The instrument's elastic strap allows the unit to be either hand-held,

or hung on nearby objects.

By sliding your hand between the instrument and its elastic strap,

you can hold onto the Monoxor II with a minimum of effort. The

instrument's front panel slide switches can then be actuated by your

thumb for one-handed operation. Or, by releasing the metal clip at the

bottom of the instrument's case, you can hang the instrument by its

strap on nearby objects such as nails, sheet metal, or valve handles.

4.5 UsingtheProbe

Arigid stainless steel probe with handle is used to draw a gas sample

fromtheroom,grilles,diffusers,andfurnaceﬂuesthroughalinedryer

and ﬂexible hose into the instrument. A ﬂexible probe option (see

Section 6) is available to give easy access to hot-water heater ﬂues

and inside furnace heat exchangers.

The probe tube is detachable from the handle when sampling with a

different probe is desired. See Figure 3.

Important! Theline-dryerwillremovemoisturefromthegassample.

If the line-dryer becomes saturated, however, condensation may be

observed within the hose. If this occurs, stop sampling and replace

the line-dryer's ﬁlter-packing material.

4.6 InterpretingtheDisplay

Gas Display The LCD shows CO levels in the

range from 0 to 1999 ppm. The display on the right

indicates a CO level of 500 ppm.

Overrange When the gas sample exceeds

1999 ppm, a “1” is displayed on the LCD. To clear

an overrange condition, leave instrument turned on

and sample fresh air until the LCD returns to displaying CO.

LowBatteryIndications Whenthebatteryvoltage

becomes low, the “LO BAT” indicator appears.

Although the instrument will continue to operate

and give CO readings under these conditions, the batteries should be

replaced as soon as possible.

When battery voltage becomes too low for the

instrument to operate, a “-1” is displayed on the

LCD. No CO readings are provided under these

conditions.

4.7 Long-TermStorage

When storing the Monoxor II for extended periods of time, set its

POWER switch to OFF and remove the batteries. The POWER OFF

position places a short across the CO sensor, thus keeping it from

being destabilized while not in use.

5 MAINTENANCE

The Monoxor II needs to be calibrated at regular intervals to be cer-

tain that it still meets its accuracy speciﬁcation.Aregular calibration

schedule should be established between you and your nearest Bacha-

rach Service Center, unless your facility has the necessary calibration

equipment and personnel trained in the maintenance of gas-detection

equipment. Detailed calibration , maintenance procedures and re-

placementpartslistsareprovidedintheServiceManual(0019-9166).

As a quick check of the instrument’s operation, perform a response

check by exposing the instrument to a source of CO (e.g., cigarette

smoke, smoke from a recently snuffed-out match, bottled CO). If the

instrument doesn’t show the presence of CO, or if the reading is obvi-

ously in error, DO NOT use the instrument until it has been serviced

by an authorized Bacharach Service Center.

NOTE: DO NOT use this simple response check as a sub-

stitute for ensuring the instrument is properly calibrated.

6 PARTS / SERVICE

6.1 Parts/AccessoriesList

Item Part No.

Battery Cover 0019-3029

Probe/Hose/Line Dryer Assy. 0019-3084

Flexible Probe Tube (optional) 0019-3104

Line Dryer Filter Packing 0011-0122

6.2 BacharachSales / ServiceCenters

United States

Bacharach, Inc.

621 Hunt Valley Circle

New Kensington, PA 15068

Phone: 724-334-5051

Fax: 724-334-5723

Email: [email protected]

Canada

Bacharach of Canada, Inc.

20 Amber St. Unit #7

Markham, Ontario L3R SP4

Canada

Phone: 905-470-8985

Fax: 905-470-8963

Email: [email protected]

7 HAZARDS OF CARBON MONOXIDE

Carbonmonoxidepoisoningresultsinheadache,nausea,chronictired-

ness, confusion, dizziness, and sometimes coma or death. It effects

people by cutting off the supply of oxygen to their muscles and brain.

Theharmful effectsofcarbon monoxide exposure dependon both the

concentration of CO in the air and the length of exposure.

Concentration Inhalation time and toxic

of CO in air symptoms developed

50 ppm* (0.005%) Maximum allowable concentration for

continuous exposure in any 8-hour period.

200 ppm* (0.02%) Slight headache, tiredness, dizziness,

nausea after 2–3 hours.

400 ppm (0.04%) Frontal headaches within 1–2 hours,

life-threatening after 3 hours.

800 ppm (0.08%) Dizziness, nausea and convulsions within

45 minutes. Unconsciousness within

2 hours. Death within 2–3 hours.

1,600 ppm (0.16%) Headache, dizziness and nausea within

20 minutes. Death within 1 hour.

3,200 ppm (0.32%) Headache, dizziness and nausea within

5–10 minutes. Death within 30 minutes.

6,400 ppm (0.64%) Headache, dizziness and nausea within

1–2 minutes. Death within 10–15 minutes.

12,800 ppm (1.28%) Death within 1–3 minutes.

For more information on CO ask about Bacharach's

CO Regional Training Seminars.

*Maximum CO concentration for exposure at any time as prescribed

byOSHA.Effectscanvarysigniﬁcantlybasedonage,sex,weight and

overall state of health.

Andere Handbücher für Monoxor II

Inhaltsverzeichnis

Andere Bacharach Messgerät Handbücher

Bacharach

Bacharach 2825 Bedienungs- und Wartungshandbuch

Bacharach

Bacharach 3010 Bedienungsanleitung

Bacharach

Bacharach Fyrite INSIGHT PLUS Bedienungsanleitung

Bacharach

Bacharach AGM300 Bedienungsanleitung

Bacharach

Bacharach 19-8104 Fehlerbehebungshandbuch

Bacharach

Bacharach Parasense GRM2 CO2 Series Handbuch

Bacharach

Bacharach Leakator Jr. Bedienungsanleitung

Bacharach

Bacharach MONOXOR XR Bedienungsanleitung

Bacharach

Bacharach HGM300 Leitfaden

Bacharach

Bacharach MGS-250 Bedienungsanleitung

Bacharach

Bacharach Fyrite Tech 50 Bedienungsanleitung

Bacharach

Bacharach HGM-MZ Bedienungsanleitung

Bacharach

Bacharach 24-7224 Bedienungsanleitung

Bacharach

Bacharach HGM300 Leitfaden

Bacharach

Bacharach Gas Pup Bedienungsanleitung

Bacharach

Bacharach Neutronics Mini-ICS Bedienungsanleitung

Bacharach

Bacharach MGC100 Bedienungsanleitung

Bacharach

Bacharach 0012-9015 Bedienungsanleitung

Bacharach

Bacharach Comfort Chek 400 Bedienungsanleitung

Bacharach

Bacharach Monoxor Plus Bedienungsanleitung

Bacharach

Bacharach Snifit 40 Bedienungsanleitung

Bacharach

Bacharach Tru Pointe Betriebsanleitung

Bacharach

Bacharach Portable Combustion Analyzer Bedienungsanleitung

Bacharach

Bacharach Parasense 3300RM2 Handbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung