Badger Meter ORION SE Installations- und Benutzerhandbuch

ORION® SE

Integral Endpoint for American® Residential Gas Meters

Installation Data

ORI-I-56 (1-11)

62014-097 Rev. 3

IMPORTANT:

This manual contains important information.

READ AND KEEP FOR REFERENCE.

ORION® SE Integral Endpoint for American® Residential Meters

Page ii (1-11)

Installation Data

CONTENTS

DISCLAIMER .....................................................................................................................................5

QUESTIONS OR SERVICE ASSISTANCE ...........................................................................................5

PRODUCT IDENTIFICATION.............................................................................................................5

SCOPE OF MANUAL .........................................................................................................................5

PRODUCT UNPACKING AND INSPECTION......................................................................................6

LICENSE REQUIREMENTS ................................................................................................................6

INSTALLATION TOOLS AND MATERIALS ........................................................................................6

LABEL INFORMATION ......................................................................................................................6

AMERICAN GAS METERS .................................................................................................................7

Meter and Indexes Before Endpoint............................................................................................................................7

Index Removal From an American Gas Meter ............................................................................................................7

ORION AMERICAN METER INSTALLATION MATERIALS ................................................................9

ASSEMBLE THE ORION ENDPOINT AND INDEX ...........................................................................10

Endpoint Gaskets Attachment.....................................................................................................................................10

Place Four (4) Screws Into the Endpoint .....................................................................................................................11

INDEX INSTALLATION ....................................................................................................................12

Place Screws in Slotted Index ......................................................................................................................................12

Place Screws in Index With Holes.................................................................................................................................12

Drive Pawl Engagement And Index Installation ........................................................................................................13

PLACE THE ENDPOINT AND INDEX ON AN AMERICAN GAS METER...........................................14

Placing a Two-Feet Dial ................................................................................................................................................15

Placing a One-Foot Index.............................................................................................................................................15

PLACE THE COVER OVER THE ENDPOINT AND INDEX.................................................................16

PROGRAM THE ENDPOINT ............................................................................................................17

INSERT TAMPER PLUGS .........................................................................................................18

INSTALLATION COMPLETE ............................................................................................................18

Page iii

(1-11)

ORION® SE Integral Endpoint for American® Residential Meters

Page iv (1-11)

Installation Data

DISCLAIMER

The user/purchaser is expected to read and understand the information provided in this manual, follow any listed safety

precautions and instructions and keep this manual with the equipment for future reference.

Misuse, mishandling and/or inadequate maintenance may impair performance and/or compromise safety.

QUESTIONS OR SERVICE ASSISTANCE

If you have questions regarding the product or this document contact:

Badger Meter, Inc.

P.O. Box 245036

Milwaukee, WI 53224-9536

Telephone: (414) 355-0400, (800) 876-3837

Fax: (888) 371-5982

On the Web: www.badgermeter.com or call your local Badger Meter representative.

PRODUCT IDENTIFICATION

Record the product identication numbers from the nameplate.

Endpoint:

Model Number ________________________________________

Serial Number _________________________________________

Tag Number ___________________________________________

SCOPE OF MANUAL

This manual contains installation instructions for the Badger Meter ORION® and the Badger Meter ORION® SE integral

endpoint for American® Meter residential aluminum-case gas meters. Proper performance and reliability of the ORION gas

meter system depends upon installation in accordance with these instructions.

(1-11) Page 5

ORION® SE Integral Endpoint for American® Residential Meters

PRODUCT UNPACKING AND INSPECTION

NOTE: If damage to the shipping container is evident upon receipt, request the carrier to be present when the

product is unpacked.

Carefully open the shipping package, follow any instructions that may be marked on the exterior. Remove all cushioning

material surrounding the product and carefully lift the product from the package.

Retain the package and all packing material for possible use in reshipment or storage.

Visually inspect the product and applicable accessories for any physical damage such as scratches, loose or broken parts, or

any other sign of damage that may have occurred during shipment.

NOTE: If damage is found, request an inspection by the carrier’s agent within 48 hours of delivery and le a claim with

the carrier.

A claim for equipment damage in transit is the sole responsibility of the purchaser.

LICENSE REQUIREMENTS

This device complies with Part 15 of FCC Rules. Operation of this device is subject to the following conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

No FCC license is required by a utility to operate an ORION meter reading system.

Any changes made, but not approved by Badger Meter, can void the user’s authority to operate the equipment.

CAUTION! In accordance with FCC Regulations,“Code of Federal Regulations”Title 47, Part 2, Subpart J, Section

1091, transmitters (endpoints) pass the requirements pertaining to RF radiation exposure. However, to avoid public

exposure in excess of limits for general population (uncontrolled exposure), a 12 CM distance between the

transmitter (endpoint) and the body of the user must be maintained during testing.

INSTALLATION TOOLS AND MATERIALS

Magnetized screwdrivers:

• 1/8" at screwdriver

• 1/4” at screwdriver

• #1 Phillips screwdriver

If battery powered driver is used, ensure torque maximums are not exceeded (usually 15 in-lb).

Putty knife or at blade scraper

Badger Meter handheld programmer/data collector

LABEL INFORMATION

Certication markings are noted on the product label. Label markings include:

• Serial number and bar code plus product description

• FCC identication

• Certication markings

Page 6 (1-11)

Installation Data

AMERICAN GAS METERS

Gas meter models: AL, AC, AT, AM, AR with suxes: 175, 210, 225, 250, 310, 350, 425, 630

Meter and Indexes Before Endpoint

Index Removal from an American Gas Meter

1. Use a large screwdriver to puncture and remove tamper plugs, if present.

2. Use a large screwdriver to remove and discard the four (4) mounting screws and the cover.

Tamper

Plug

Tamper

Plug

Odometer

Style Index

Dial Index

(1-11) Page 7

ORION® SE Integral Endpoint for American® Residential Meters

3. Completely remove and discard the old gasket. Use a putty knife to clean the meter surface of all gasket remnants

that might limit the eectiveness of the new gasket.

4. Use a small screwdriver to remove the index. Discard the two (2) screws.

Use a putty knife to

clean the meter surface

of all gasket remnants

that might limit the

eectiveness of the

new gasket.

Page 8 (1-11)

Installation Data

Shown below is an American gas meter with the tamper plugs, index and gasket removed.

ORION AMERICAN METER INSTALLATION MATERIALS

Rear Gasket

Endpoint

4 Screws

¼-20 X 3/8"

Front

Gasket

Index

From Existing Meter

2 Screws #8-16 X ½"

2 Screws #8-16 X ¼"

4 Screws

#8-16 X ½"

Cover

4 Tamper Plugs

(1-11) Page 9

ORION® SE Integral Endpoint for American® Residential Meters

ASSEMBLE THE ORION ENDPOINT AND INDEX

Endpoint Gaskets Attachment

The gaskets should be attached to the endpoint at the factory. If the gaskets are not attached:

1. Place the rear gasket on the back of the endpoint. Place the rear gasket so the tab is at the top of the endpoint, the

drain slots are pointing down, facing towards the gas meter.

Drain Slots Pointing Down

Drain Slots Towards Gas Meter

2. Place the front gasket on the other side of the endpoint.

• Place the gasket so that its two holes go over the two protruding tines.

• Be sure the notched end goes around the guide pin on the right side of the endpoint.

Holes Over Tines Notched End Around Guide Pin on

Right of Endpoint

Tab on Top

Page 10 (1-11)

Andere Handbücher für ORION SE

Inhaltsverzeichnis

Andere Badger Meter Messgerät Handbücher

Badger Meter

Badger Meter FC-5000 Bedienungsanleitung

Badger Meter

Badger Meter 6200 Bedienungsanleitung

Badger Meter

Badger Meter iSonic 2000 Bedienungsanleitung

Badger Meter

Badger Meter PRESO COIN Bedienungsanleitung

Badger Meter

Badger Meter EPM Bedienungsanleitung

Badger Meter

Badger Meter Dynasonics DXN Bedienungsanleitung

Badger Meter

Badger Meter Trimble Ranger 3 Bedienungsanleitung

Badger Meter

Badger Meter M-series Bedienungsanleitung

Badger Meter

Badger Meter QuikSert Standard Bedienungsanleitung

Badger Meter

Badger Meter Blancett B3100 Series Bedienungsanleitung

Badger Meter

Badger Meter ModMAG M1000 Bedienungsanleitung

Badger Meter

Badger Meter ModMAG M Series Bedienungsanleitung

Badger Meter

Badger Meter ER-9 Bedienungsanleitung

Badger Meter

Badger Meter M5000 Bedienungsanleitung

Badger Meter

Badger Meter ModMAG M-Series M7600 Bedienungsanleitung

Badger Meter

Badger Meter Blancett QuickSert B134C-400 Bedienungsanleitung

Badger Meter

Badger Meter DN15 Bedienungsanleitung

Badger Meter

Badger Meter FC-5000 Bedienungsanleitung

Badger Meter

Badger Meter ModMAG M1000 Bedienungsanleitung

Badger Meter

Badger Meter Vortex VN2000 Bedienungsanleitung

Badger Meter

Badger Meter ILR7 Series Bedienungsanleitung

Badger Meter

Badger Meter Preso Gemini Cone Bedienungsanleitung

Badger Meter

Badger Meter Blancett B2800XP Bedienungsanleitung

Badger Meter

Badger Meter ER-9 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung