Bake Max DOUGH MOULDER Bedienungsanleitung

OPERATION MANUAL FOR DOUGH MOULDER

1. INSTALLATION

Dough Moulder has 4wheels and can be easily moved around.

You will only have to connect the electric power supply to it according to

nameplate. The Moulder is ready for start up and operation.

2. OPERATION

（1）Loosen the two dough feed guide knob and move the dough feed guide

on both sides to the right position according to the weight of the dough and

tighten the dough feed guide knob again. The position of dough feed guide

should be so adjusted the dough feed guide should not touch the dough.

（2）Adjust the top roller and bottom roller gap by the corresponding knob. The

gap should be close enough to squeeze out the air inside the dough and get

the required diameter and length of the dough piece after molding. But the gap

should not be too small to damage the surface of the dough.

（3）Check whether the position of curling wire mesh is alright. Adjust it in

case the dough rolling up is too loose or too tight.

（4）adjust the position of presser board to presser board to press the dough

piece to the right tightness and to the right length.

PRESSER BOADR

MAIN SWITCH

DOUGH FEED

GUIDE KNOB

DOUGH FEED GUIDE

GURLING WIRE MESH

TOP ROLLER GAP ADJ. KNOB

BOTTOM ROLLER

GAP ADJ. KNOB

DOUGH MOULDER

C/No DESCRIPTION Q’TY C/No DESCRIPTION Q’TY C/No DESCRIPTION Q’TY

1 BRACKET 1 41 POWER 1 81 PLATE 1

2 BRACKET 1 42 POLLER 1 82 SHAFT 1

3 ROLLER 3 43 POLLER SHAFT 1 83 BLET 1

4 ROLLER 1 44 SCREW ROD 2 84 CHAIN WHEEL 1

5 BEARING 8 45 HANDLE WHEEL 2 85 PLATE 1

6 SLIDE BLOCK 2 46 BELT PLATE 1 86 WASHER 4

7 SLIDE BLOCK 2 47 BELT 1 87 PIN 6

8 SPRING 4 48 PLATE 1 88 CHAIN WHEEL 1

9 ROD 3 49 PLATE 1 89 CHAIN WHEEL 1

10 SCREW ROD 2 50 CLASS 1 90 CHAIN 1

11 CHAIN WHEEL 4 51 PLATE 1

12 SCREW ROD 2 52 SPRING 4

13 CHAIN 2 53 PLATE 2

14 WIPPER 4 54 BLOCK 2

15 SPRING 2 55 SCREW ROD 1

16 SPRING 6 56 SCREW ROD 1

17 BLOCK 4 57 CHAIN 1

18 PIN 8 58 CHAIN 1

19 CHAIN WHEEL 1 59 CHAIN WHEEL 2

20 KEY 5 60 COVER 1

21 CHAIN 1 61 HANDLE WHEEL 3

22 ADJ PLATE 1 62 BRACKET 1

23 CHAIN WHEEL 1 63 NET 1

24 BEARING 1 64 SHAFT 1

25 SPRING 1 65 SHAFT 1

26 BEARING SET 2 66 CLASS 1

27 BEARING 6 67 COVER 1

28 CHAIN WHEEL 1 68 BELT ROLLER 1

29 BEARING 1 69 COVER 1

30 BEARING SHAFT 1 70 COVER 1

31 PLATE 3 71 COVER 1

32 CHAIN WHEEL 1 72 COVER 1

33 CHAIN WHEEL 1 73 PLATE 2

34 KEY 1 74 ROUND SCREW 2

35 CHAIN WHEEL 1 75 BEARING HOUSING 2

36 CHAIN WHEEL 1 76 SHAFT 1

37 KEY 1 77 BELT PULLEY 1

38 CHAIN 1 78 KEY 1

39 BASE 1 79 MOTOR 1

40 WHEEL 4 80 PULLEY 1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bake Max Gewerbliche Lebensmittelgeräte Handbücher

Bake Max

Bake Max BMTSC Titan Series Bedienungsanleitung

Bake Max

Bake Max BMCB001 Bedienungsanleitung

Bake Max

Bake Max BMHBD01 Bedienungsanleitung

Beliebte Gewerbliche Lebensmittelgeräte Handbücher anderer Marken

Blue Seal

Blue Seal EF30 Bedienungsanleitung

Tecfrigo

Tecfrigo Snelle 400 GS Bedienungsanleitung

Follett

Follett PFT Series Bedienungsanleitung

MEFE

MEFE CAT 206 PTR Leitfaden

Premier

Premier 900cl Bedienungsanleitung

Diamond

Diamond AL1TB/H2-R2 Bedienungsanleitung

Salva

Salva IVERPAN FC-18 Bedienungsanleitung

Hussmann

Hussmann Rear Roll-in Dairy Bedienungsanleitung

Cornelius

Cornelius IDC PRO 255 Bedienungsanleitung

Moduline

Moduline HSH E Series Bedienungsanleitung

MINERVA OMEGA

MINERVA OMEGA DERBY 270 Bedienungsanleitung

Cambro

Cambro IBSD37 Bedienungsanleitung

Fri-Jado

Fri-Jado LDR 8 s Bedienungsanleitung

Diamond

Diamond OPTIMA 700 Kurzanleitung

Allure

Allure Melanger JR6t Bedienungsanleitung

saro

saro FKT 935 Bedienungsanleitung

MKN

MKN OPGGSGARG Series Bedienungsanleitung

BIRO

BIRO 22 Service-Handbuch