Bang & Olufsen BEOLAB 6002 Bedienungsanleitung

BeoLab 6002

Guide

WARNING: To reduce the risk of fire or

electric shock, do not expose this appliance

to rain or moisture. Do not expose this

equipment to dripping or splashing and

ensure that no objects filled with liquids,

such as vases, are placed on the equipment.

To completely disconnect this equipment

from the AC Mains, disconnect the mains

plug from the wall socket. The disconnect

device shall remain readily operable.

The lightning flash with arrowhead symbol

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

Daily use

When you have finished setting

up the loudspeakers as described

on the following pages, connect

the entire system to the mains

supply. The indicator lights up

in red, indicating that the loud-

speakers are in standby, ready

to be used. The loudspeakers

are designed to be left in this

standby mode when not in use.

Switching on and off –

indicator

When you switch on your Bang &

Olufsen system, the loudspeakers

switch on simultaneously. The red

standby indicator light turns green,

indicating that the loudspeakers

are switched on.

When you switch off your system,

or mute the sound, the red

indicator light appears immediately,

indicating that the loudspeakers are

not in use.

If the loudspeakers are connected

to a non-Bang & Olufsen system,

they switch on when they receive a

signal from the system (refer to p. 6).

They switch off a few minutes after

the signal has disappeared.

Loudspeaker protection

The loudspeakers are equipped

with a thermal protection system

which prevents overheating. If an

error occurs – or the speaker units

become overheated – the system

automatically switches the loud-

speakers to standby, and the

indicator light turns orange.

To restore the situation:

> Disconnect the loudspeakers

from the mains.

> Allow the system time to reset

(approximately 3–5 minutes).

> Reconnect the loudspeakers to

the mains.

Should the problem persist, contact

your Bang & Olufsen retailer.

Cleaning the loudspeaker

Wipe dust off the surfaces using a

dry, soft cloth. If necessary, remove

stains or dirt with a soft, damp

cloth and a solution of water and

mild detergent such as washing-up

liquid.

Never use alcohol or other solvents

to clean any part of the loud-

speakers!

NOTE! Prolonged listening at high

volume levels may cause hearing

damages.

Indicator

Set up the loudspeaker

We recommend that you follow

this procedure:

– Disconnect your system from the

mains supply.

– Place the loudspeakers in your

setup.

– Set the switches to the correct

setting. This is explained in ‘Adapt

the loudspeakers to your setup’

(pages 6–7).

– Connect your speaker system.

– Connect the entire system to the

mains again.

If you mount the loudspeaker on a

wall bracket, you cannot assemble

the base to the loudspeaker.

Cautions

– Make sure that the loudspeakers

are placed and connected in

accordance with the instructions

in this Guide. To prevent injury,

use Bang & Olufsen approved

stands and wall brackets only!

– The loudspeakers can only be

switched off completely by

disconnecting them from the

wall socket.

– The loudspeakers are designed

for indoor use in dry, domestic

environments only, and for use

within a temperature range of

10–40º C (50–105º F).

– Remember that all speakers in a

setup must be connected to a

mains outlet, and that they are

designed to be connected to the

mains at all times, as this allows

them to switch on automatically.

– Do not attempt to open the loud-

speaker. Leave such operations to

qualified service personnel!

Column and base

It is easiest to assemble the base and

the speaker column if the loud-

speaker is lying on a table.

In order to protect the table and

the column from being scratched,

we recommend that you place the

wrapping foam on the table first.

Hook the base plate onto the two

guiding pins at the bottom of the

speaker column (be careful not to

drop the base plate!). Insert the

three screws and tighten them

securely.

Cable connections

The loudspeakers can be used

with Bang & Olufsen audio,

video and link systems. They may

also be used with non-Bang &

Olufsen systems. For specific

information about the sockets on

your system, refer to the Guide

enclosed with the system.

The socket panel is located at the

bottom of the loudspeakers.

Power Link connections: These

connections carry both the right

and left sound signals. Therefore,

you can:

1run a Power Link cable from your

Bang & Olufsen system directly

to each loudspeaker, or…

2run a Power Link cable from your

Bang & Olufsen system to the

first loudspeaker, and then run

another Power Link cable to the

next loudspeaker. This will often

help to minimise cable clutter.

For safety reasons you must run

the cables to and from the loud-

speaker through the cable guides.

Mains cord: The supplied mains

cord and plug are specially designed

for the product. If you change the

plug or damage the mains cord, you

must buy another from your Bang &

Olufsen retailer!

LEFT RIGHT LINE

1 POWER LINK 2

SETUP

CORNER WALL FREE

POSITION

POWER LINK POWER LINK

LEFT RIGHT

Connection to the

mains supply

SETUP switch

POWER LINK

socket

POSITION switch

Adapt the loudspeakers to your setup

The loudspeakers may be placed

almost anywhere in your room.

However, the most natural

sound is obtained if they are set

up as explained on these pages.

SETUP switch

This switch has three settings: LEFT,

RIGHT and LINE.

Set the switch to LEFT or RIGHT

when connecting the loudspeakers

in a Bang & Olufsen system. Set

the switch to LINE when

connecting the loudspeakers in a

non–Bang & Olufsen system.

…To a Bang & Olufsen system:

Use the enclosed Power Link cables

to connect the loudspeakers to your

system. Set the SETUP switch to

LEFT and RIGHT (the left and right

sound channel) respectively.

…To a non-Bang & Olufsen

system:

Use a special adaptor with an

ordinary phono/RCA plug in one

end, and a DIN-plug in the other.

Depending on your setup, you may

also need to connect an adaptor

with phono/RCA and mini jack

plugs (optional accessories, available

from your Bang & Olufsen retailer).

Set the SETUP switch to LINE.

The POSITION switch

When a loudspeaker is placed in a

corner or close to a wall, the bass

level is boosted compared to the

bass level from a loudspeaker placed

in a more free-standing position.

To remove this excessive bass boost,

set the POSITION switch to ensure

that the bass level suits the

placement of the loudspeaker. The

appropriate switch setting depends

on the distance from the loud-

speaker to the walls and corners of

the room. Use the guidelines

mentioned here, when deciding

which of the three POSITION

switch settings to select – on each

loudspeaker.

The position zones, shown on the

next page, are meant as guidelines

– you may, of course, set the switch

to any of the three settings you

prefer.

CORNER

Use this setting if the loudspeaker

is placed in a corner – shown by the

dark grey areas in the illustration.

WALL

Use this setting if the loudspeaker

is placed less than 15 cm (6") from

the wall, and no closer to a corner

than 50 cm (20") – shown by the

grey areas along the walls in the

illustration.

If the loudspeaker is mounted on a

wall bracket, use this setting.

FREE

Use this setting if the loudspeaker is

placed more than 15 cm (6") from

the wall, and no closer to a corner

than 50 cm (20") – shown by the

large light grey area in the

illustration.

How to measure? The distances

referred to are measured as shown

here (the loudspeaker seen from

above).

CORNER

WALL

FREE

Position zones: The three settings

(CORNER–WALL–FREE) correspond

to the position zones marked in

different shades of grey.

Waste Electrical and Electronic

Equipment (WEEE) –

Environmental protection

Electrical and electronic equipment,

parts and batteries marked with

this symbol must not be disposed

of with normal household wastage;

all electrical and electronic equip-

ment, parts and batteries must be

collected and disposed of separately.

When disposing of electrical and

electronic equipment and batteries

by use of the collection systems

available in your country, you

protect the environment, human

health and contribute to the

prudent and rational use of natural

resources. Collecting electrical and

electronic equipment, batteries

and waste prevents the potential

contamination of nature with the

hazardous substances which may

be present in electrical and elec-

tronic products and equipment.

Your Bang & Olufsen retailer will

advise you of the correct way of

disposal in your country.

If a product is too small to be

marked with the symbol, it will

appear in the User Guide, on the

Guarantee certificate, or on the

packaging.

This product is in conformity with the provisions of the Directives

2004/108/EC and 2006/95/EC.

For the Canadian market only!

This class B digital apparatus meets

all requirements of the Canadian

Interference-Causing Equipment

Regulations.

For the US-market only!

NOTE: This equipment has been

tested and found to comply with the

limits for a class B digital device,

pursuant to part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against

harmful interference in a residential

installation.

This equipment generates, uses and

can radiate radio frequency energy

and, if not installed and used in

accordance with the instructions,

may cause harmful interference to

radio communications. However,

there is no guarantee that inter-

ference will not occur in a particular

installation. If this equipment does

cause harmful interference to radio

or television reception, which can be

determined by turning the equip-

ment off and on, the user is

encouraged to try to correct the

interference by one or more of the

following measures:

– Reorient or relocate the receiving

antenna.

– Increase the separation between

the equipment and receiver.

– Connect the equipment into an

outlet on a circuit different from

that to which the receiver is

connected.

– Consult the retailer or an

experienced radio/TV technician

for help.

Technical specifications, features

and the use thereof are subject to

change without notice!

All Bang & Olufsen products comply

with applicable environmental

legislation throughout the world.

Inhaltsverzeichnis

Andere Bang & Olufsen Sprecher Handbücher

Bang & Olufsen

Bang & Olufsen BEOLAB 8002 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 6000 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 8000 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 6000 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 3000 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 7-4 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Balance Beosound Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLink Active Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoPlay A9 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beolit 15 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 3500 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound Core Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 7-6 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 20 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 7-4 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 17 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beosound Level Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab Penta Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEOLINK VIDEO Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beolab 8 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 2 3rd Generation Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beolit 15 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 20 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 2 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung